Required Information, Hardware Address | Lantronix 900-653-R

3: Installation of xDirect

4.For non-PoE xDirect unit, supply power to your unit using the power supply that was included in the packaging.

Note: The provided power supply is 5 VDC 1A. For all xDirect units power can also be supplied via pin 9 (+) and pin 5 (-) on the DB9F connector (voltage range = 5 VDC to 15 VDC). The xDirect will draw 1.3W max power.

Required Information

Before configuring the xDirect, have the following information available:

Hardware Address

Take note of the unit’s hardware address (also known as the Ethernet or MAC address). It is on the product label, in the format: 00-80-A3-XX-XX-XX, where the XXs are unique numbers assigned to the product (see Product Information Label).

Hardware Address: _____-_____-_____-_____-_____-_____

IP Address

The xDirect must have a unique IP address on your network. This address references the specific unit. By default, the unit is DHCP-enabled and automatically assigned an IP address on DHCP- enabled networks. If you are assigning a static IP address, the systems administrator generally provides the IP address, subnet mask, and gateway.

Note: The factory default IP address is 0.0.0.0 to enable DHCP, BOOTP, and AutoIP. When the units boots, it sends a DHCP broadcast to try and get an IP address. If it receives no reply from a DHCP server, the xDirect tries BOOTP. If the xDirect does not receive a response from BOOTP, it reverts to an AutoIP address.

IP Address:	_______	_______	_______	_______
Subnet Mask:	_______	_______	_______	_______
Gateway:	_______	_______	_______	_______

You have several options for assigning an IP address and related network settings to your unit. This chapter provides information about using the DeviceInstaller (graphical user interface) and serial port login (command line interface) methods.

Note: For information about other methods of assigning the IP address, such as DHCP,

AutoIP, ARP, and Telnet, see Appendix D: Alternative Ways to Assign an IP Address.

xDirect User Guide

17

Image 17

Lantronix 900-653-R manual Required Information, Hardware Address, IP Address

Contents

User Guide Copyright & Trademark WarrantyContacts Disclaimer Using this Guide Table of ContentsInstallation of xDirect Using DeviceInstaller Configuration Via Telnet or Serial Port Setup Mode Configuration Using Web Manager Setup Mode Channel Configuration Setup Mode Server Configuration Monitor Mode Setup Mode Advanced SettingsFirmware Upgrades Appendix B Connections and Pinouts Appendix a Troubleshooting and Contact InfoAppendix E Binary to Hexadecimal Conversions Appendix F Compliance Serial Tunneling Example List of Figures List of Tables Chapter Summary Using this GuidePurpose and Audience Document Description Additional Documentation Applications Key FeaturesIntroduction Introduction Protocol Support Additional FeaturesConfiguration Methods Product Label Product Information Label Installing the xDirect Installation of xDirectPackage Contents IP Address Required InformationHardware Address Installing DeviceInstaller Using DeviceInstallerTo install DeviceInstaller Assigning an IP Address Viewing the Current Configuration Accessing the xDirect Using DeviceInstallerTo view the units current settings XDirect Configuration in DeviceInstaller Comments Supports Configurable PinsDevice Family Type Next Step Assigning the IP Address Serial Port Login Accessing xDirect Using DeviceInstaller Configuration Using Web Manager Configuration Using Web Manager Network Mode Network ConfigurationAutomatic IP Address Configuration To assign an IP address automatically Ethernet Configuration Static IP Address ConfigurationSelect Use the following IP configuration To assign an IP address manually To configure the xDirect device server settings Server Configuration CPU Performance Mode Monitor Mode @ BootupConfig Server Port Timeout ms To configure the host list Host List ConfigurationRetry Timeout Retry Counter To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Baud Rate Enable PackingData Bits Parity Accept Incoming Connection Settings TCPTo configure a channel’s TCP settings Modem Mode Password RequiredModem Escape Sequence Pass Through To configure a channel’s UDP settings Connection Settings UDP Device Address Table Datagram TypeUse Broadcast Apply Defaults Apply Settings Accessing Setup Mode Configuration Via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connection Password Press Enter for Setup Mode Serial Port Connection Exiting Setup ModeTwo options through which to exit setup mode Server Configuration Option Setup Mode Server ConfigurationBootP/DHCP/AutoIP options IP Address Netmask Number of Bits for Host Part Set Gateway IP AddressSet DNS Server IP Address Standard IP Network Netmasks Dhcp Name Change Telnet Configuration Password Baudrate Setup Mode Channel ConfigurationChannel 1 Option Interface Mode Options Interface ModeCommon Interface Mode Settings Flow Port Number Connect ModeFlow Control Options Reserved Port Numbers Incoming Connection Connect Mode OptionsConnect Mode Option Manual Connection Address Example ResponseActive Startup C0.0.0.0/0 Host List Option HostlistAutostart Automatic Connection To enable the hostlist Modem ModeDatagram Type Directed UDP Message Meaning Modem Mode Messages 10 Modem Mode Commands Send the Escape Sequence +++ in Modem ModeModem Mode Function Command Show IP Address after Ring Auto Increment Source Port Disconnect Mode DisConnModeRemote IP Address Remote Port 12 Flush Mode Options Flush Mode Buffer Flushing11 Disconnect Mode Options Packing Interval Pack ControlTrailing Characters Send Characters Channel Port Password DisConnTime Inactivity TimeoutSend Characters Telnet Terminal Type Expert Settings Option Setup Mode Advanced SettingsARP Cache Timeout In Seconds TCP Keepalive Time In Seconds Security Settings Option Snmp Community Name Disable SnmpDisable Telnet Setup Disable Port 77FE Hex Disable Tftp Firmware UpdateDisable Web Server Disable Web Setup Enable Enhanced Password Default Settings Option Expert Settings Defaults Channel 1 Configuration DefaultsSecurity Settings Defaults Setup Mode Advanced Settings Using Tftp Graphical User Interface Firmware UpgradesObtaining Firmware Reloading Firmware Firmware Files To recover firmware Using Tftp Command Line Interface Firmware Upgrades Entering Monitor Mode Using the Serial Port Monitor ModeEntering Monitor Mode Using the Network Port To enter Monitor Mode locally Monitor Mode Commands Monitor Mode CommandsCommand Command Name Function G0, G1, ....,Ge, Gf Response Meaning Command Response Codes LEDs Appendix a Troubleshooting and Contact InfoStatus LED Table A-2 Status LED RJ45 Ethernet LED Problems and Error MessagesSerial LEDs Using DeviceInstaller Serial Settings on page 29 or Europe, Middle East and Africa Technical SupportUnited States Serial Port Pinouts Appendix B Connections and Pinouts Table B-6 Ethernet RJ45 Connector Pin-Outs Ethernet Connector Pinouts Power Jack Mini USB-B Category Description Appendix C Technical SpecificationsTable C-1 xDirect Technical Specifications Appendix C Technical Specifications AutoIP Appendix D Alternative Ways to Assign an IP Address To assign a temporary IP address ARP and Telnet Converting Binary to Hexadecimal Appendix E Binary to Hexadecimal ConversionsConversion Table Scientific Calculator Appendix E Binary to Hexadecimal Conversions Appendix F Compliance SafetyManufacturer’s Name & Address Electromagnetic Emissions RoHS Notice Appendix F Compliance