Serial Interface, Front of XPress DR+

Chapter 3: Installation and Hardware

Figure 3-2. Front of XPress DR+

Serial Interface

The XPress DR+ supports RS-232 via RJ45 connectors. It also supports RS-422/485 via screw terminals (Serial Port 2 only).

Note: Serial Port 2 supports RS232, RS422, and RS485, but only one mode at a time. This means you can use either the RJ45 connector or the terminal block, not both.

The RJ45 serial connectors only support RS232, up to 230400 bits per second.

XPress DR+ User Guide

Page 20

Image 20

Lantronix manual Serial Interface, Front of XPress DR+

Contents

XPress DR+ User Guide Date Rev Comments Lantronix Corporate HeadquartersTechnical Support Sales Offices Contents Contents Using DeviceInstallerConfiguration Using Web Manager Setup Mode Channel Configuration Configuration Using Telnet or Serial Port Setup ModeSetup Mode Server Configuration Setup Mode Advanced Settings Expert Settings Option 5 Firmware Upgrades Monitor ModeTroubleshooting and Technical Support Appendix D Binary to Hexadecimal Conversions 108 Appendix F Warranty 115 Index 116 Figures Tables Using This Guide Purpose and AudienceSummary of Chapters Chapter Description Using This Guide Additional Documentation Introduction Product Description Introduction XPress DR+ Front Industrial Automation Protocols Network Protocols Serial Tunneling XPress DR+ Application Examples Example of Serial Tunneling Addresses and Port Numbers Hardware AddressIP Address Port Numbers Configuration Methods Lantronix Web Manager. See Configuration Using Web Manager Installation and Hardware Physically Connecting the XPress DR+Whats in the Box? What Must the User Provide? Installation and Hardware XPress DR+ Front Panel Serial Interface Front of XPress DR+ Screw Terminal Serial Connectors RJ45 Serial Connector PinoutsSerial Screw Terminal Pinout for RS422 4-Wire Serial Screw Terminal Pinout for RS485 2-Wire Pin RS-232 to Serial RJ45 Cable P/N DTE, 9-Pin XPress DR+ Female Serial RJ45 Ethernet Interface Ethernet Interface SignalsTypical RJ45 Connector Multi-Drop Ethernet Connections Power RequirementsReset Switch Ethernet Activity LED LEDsRXD Activity LED TXD Activity LED Ethernet Link LED XPress DR+ LED Functions DimensionsStatus Meaning Wall Mount Bracket Product Information Label Serial Tunneling Network XPress DR+WApplication Examples XPress DR+W Ad Hoc NetworkSerial Tunneling Infrastructure Physically Connecting the XPress DR+W Ad Hoc XPress DR+W Connection Typical XPress DR+W Configuration Front Panel Description Required Information for Initial Configuration XPress DR+W LED Functions Installing the XPress DR+W for Initial Configuration Server Configuration OptionWlan Settings IP Address Subnet Mask Gateway Network Mode XPress DR+W only BootP/DHCP/AutoIP optionsSet Gateway IP Address Options Bit Wlan Configuration Option Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Change Dhcp Device Name Adhoc Network Channel TopologyNetwork Name Ssid Passphrase Key Type Encryption KeyHex WPA WPA2/802.11i Fixed or Automatic Data Rate Next Steps Transmission Data Rate Using DeviceInstaller Installing DeviceInstallerTo install DeviceInstaller Assigning an IP Address Accessing the XPress DR+ Using DeviceInstaller Viewing the Current ConfigurationUsing DeviceInstaller To view the units current settings Setting Description Supports Configurable PinsSupports Http Setup Supports Dynamic IP Configuration Using Web Manager Configuration Using Web ManagerAccessing XPress DR+ Using DeviceInstaller Network Configuration Lantronix Web Manager Automatic IP Address Configuration To assign an IP address automaticallyAutoIP Dhcp Host Name Server Configuration Static IP Address ConfigurationDefault Gateway To assign an IP address manually Advanced Server ConfigurationTo configure the units device server settings 0x77FE Server Port MTU Size Host List ConfigurationTo configure the units host list Channel Configuration Serial SettingsRetry Settings To configure the channel’s serial settings Port Settings Channel Flush Output Buffer Network to Serial Pack ControlFlush Input Buffer Serial to Network Connection Settings TCP To configure a channel’s TCP settings Connect Mode Passive Connection Connect Mode Active ConnectionEndpoint Configuration Connect Protocol Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Common Options Datagram Mode Datagram Type Wlan Configuration XPress DR+W only Device Address Table To configure the XPress DR+W’s Wlan settings Wlan Settings Ad Hoc Network Type Wireless Network Configuration Network Name SsidNetwork Type Channel WPA Options Wireless Network SecurityWEP Options Applying Settings Applying Factory DefaultsAdvanced Settings WPA2/802.11i Options Configuration Using Telnet or Serial Port Setup Mode Accessing Setup Mode To establish a Telnet connection Configuration Using Telnet or Serial Port Setup ModeSerial Port Connection Exiting Setup Mode To exit setup mode Setup Mode Server Configuration Setup Mode Server Configuration Dhcp Name Baudrate Setup Mode Channel ConfigurationChannel 1 Option 1 and Channel 2 Option Interface Mode Setup Mode Channel ConfigurationMode Option Common I/F Mode Setting Binary Hex Flow Port NumberFlow Control Option Hex Port Numbers Reserved for Connect Mode Connect Mode Option Active Startup Incoming ConnectionResponse Hostlist Autostart AutomaticConnection Modem Mode To enable the hostlistDatagram Type Directed UDP Message Meaning Modem Mode Function Command Modem Mode Commands Remote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Disconnect Mode Option Disconnect Mode OptionsRemote Port DisConnMode Option Flush Mode Buffer FlushingPack Control DisConnTime Inactivity Timeout Packing IntervalTrailing Characters Send Characters Channel Port Password Wlan Settings XPress DR+W OnlySend Characters Telnet Terminal Type Topology 0=Infrastructure, 1=Adhoc 0 ? WEP WEP64 or 13 WEP128 bytes and limits the number of key TX Data rate 0=fixed, 1=auto fallback 1 ? Enable Power Management Setup Mode Advanced Settings Expert Settings OptionARP Cache timeout in seconds Disable Monitor Mode at bootup Security Settings Option Enable alternate MACSetup Mode Advanced Settings Http Port Number Disable Snmp Disable Telnet SetupDisable Tftp Firmware Upgrade Disable Port 77FE Hex Default Settings Option Expert Settings Security SettingsWlan Settings XPress DR+W only Topology AdHoc Network Name Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM File To recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Firmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode Commands Monitor Mode Command Command Name FunctionMonitor Mode Commands G0, G1, ....,Ge, Gf Command Response Codes Response Meaning Troubleshooting and Technical Support Problems and Error MessagesProblem/Message Reason Solution Problems and Error Messages Troubleshooting and Technical Support XPress DR+ User Guide 101 Technical Support Technical Support Europe, Middle East, and Africa Appendix a Technical Specifications XPress DR+ and XPress DR+W Specifications Category Ieee 802.11b/g Appendix a Technical SpecificationsXPress DR+W Wireless Specifications Applications Appendix B Lantronix Cables and AdaptersLantronix P/N Description Appendix C Alternative Methods of Assigning an IP Address AutoIP To assign a temporary IP address ARP and TelnetAppendix C Alternative Methods of Assigning an IP Address Appendix D Binary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific Calculator Appendix D Binary to Hexadecimal Conversions Appendix E Compliance Information Declaration of ConformityElectromagnetic Emissions and Immunity XPress DR+ Emissions Immunity Electromagnetic Emissions and Immunity XPress DR+W Appendix E Compliance InformationRadio Canada Industry Canada Notice XPress DR+W Regulatory InformationUSA Federal Communications Commission FCC Notice Exposure of Humans to RF Fields Europe R&TTE Directive 99/5/EC, Wireless NoticeAntenna Notice Australia & New Zealand Wireless Notice Appendix F Warranty Index