Call Type Number of Required UDP Ports | LG Electronics AVS2400

38Installation

3

Installation

H.323 two-way call required ports:

	Call Type		Number of Required UDP and TCP Ports

		• 8 UDP ports (6 if presentations are disabled)
		•	2 TCP ports
	Video	•	TCP port 1720
		• Each additional video participant added requires 8 UDP ports and 2 TCP ports per H.323
			participant.

		•	2 UDP ports
	Voice	•	2 TCP ports
	Voice	•	TCP port 1720
		•	TCP port 1720
		• Each additional audio participant added requires 2 UDP ports and 2 TCP ports.

SIP two-way call required ports:

Call Type		Number of Required UDP Ports

	•	6 UDP ports
Video	•	UDP port 5060
	• Each additional video participant added requires 6 UDP ports per SIP participant.

	•	2 UDP ports
Voice	•	UDP port 5060
	• Each additional audio participant added requires 2 UDP ports.

Configuring Quality of Service

You can specify network Quality of Service (QoS) settings in the Administrator Preferences : Network : Network QoS preferences.

Set these preferences according to the settings used in your network.

NOTE

Network QoS preferences are supported with IPv4 addressing only. If you enable IPv6 addressing on your LifeSize system, QoS preferences are ignored for IPv6 calls. For more information about IPv6 addressing, refer to “Enabling IPv6 Addressing” on page 36.

You can specify DiffServ (differentiated services) or IntServ (integrated services) values for audio, video, and data packets. You can also set the IntServ Type of Service (ToS) preference.

Configuring LifeSize Transit Preferences

If you are using LifeSize Transit with your system, refer to your LifeSize Transit documentation for information about how to configure preferences in Administrator Preferences : Network : LifeSize Transit.

Image 38

LG Electronics AVS2400 owner manual Call Type Number of Required UDP and TCP Ports, Call Type Number of Required UDP Ports

Contents

Video Conference Monitor Safety Information Regulatory Information FCC Part Lamps Contain Mercury, Dispose Properly Disposal of your old applianceEEE Compliance with Directive. for Turkey only Or moisture, does not operate normally, or has been dropped On Safety On Installation On Disposal On CleaningOn Repacking Lifting and moving the VCS Contents Mode settings Customizing OSD settingsMenu settings Specifications Features Introduction VCS Body Remote control and batteries Unpacking Overview Front of the VCS OSD lock / unlock function Power cord Inlet AC in Connects the power plugRear of the VCS Remote Control Battery Installation Connections Attaching the stand Using the Kensington security system optional Disassembling the stand Audio Connecting to a PCVideo Hdmi connection SUB connection Connecting Network Connecting Power Connecting Headphones Connecting a Microphone Adjusting the angle of the Monitor and camera Attaching the back cover Initial settings for VCS Default administrator password is 1 2 3 Set the options of the Identification menu and press Set the options of the Network menu and press button Installation Main screen overview Icon Accessing the System Menu User Preferences setup Access User Preferences from which you can do the following Administration Using the Remote Control Administrator PreferencesAccessing Administrative Features Administration from a Web Browser Installation Configuring Call Preferences Admission Control Configuring Security PreferencesControlling Remote Administration Changing the Administrator Password Setting the User Password Configuring Audio Codec Order Viewing Recent Configuration ChangesConfiguring Audio Behaviors Adjusting Audio Levels Administrator Preferences AudioTesting Primary Audio Output Selecting the Active Microphone Specifying the Hostname and Domain Name Service DNS Servers Configuring Network UsageSpecifying a Locally Configured IP Address Specifying Network Speed Enabling IPv6 Addressing Specifying a Vlan TagSpecifying an NTP Server Enabling Network Address Translation NAT Restricting Reserved Ports Call Type Number of Required UDP and TCP Ports Configuring Quality of ServiceConfiguring LifeSize Transit Preferences Call Type Number of Required UDP Ports Disabling Access to the Local Directory Populating the Corporate Directory Reading from an Ldap Server Ldap preferences are not configuredConfiguring Auto Discovery Server and receive data was successful Configuring Communications Preferences Enabling Telepresence Receiving Presentations Configuring Dialing OptionsSpecifying H.323 Settings Virtual Link Data Sharing Configuring SIP Settings Enabling H.460 Support for H.323 Calls Configuring Appearance Preferences Video Layout Preferences Locking the Camera Presets Configuring Video BehaviorsConfiguring Display Preferences Controlling the Camera Use by Far End Users Adjusting the MTU of Video Packets Configuring System SettingsAdjusting Video Encoder Quality Selecting Priority of Quality Metrics for Source Video Navigate to Administrator Preferences System License Keys Rebooting the System automaticallyManually Setting System Date and Time Identifying the System Hours to complete Installing a License Key ManuallyNavigate to Preferences System License Keys Using Diagnostics Preferences and Tools Restoring Default Settings Rebooting the System Using Camera Diagnostic PreferencesUsing Network Utilities Do Not Disturb Saving and Restoring a System Configuration Exclusive Web Administration FeaturesUsing Advanced Directory Features Upgrading System Software Copying Screen Text to the ClipboardDownloading Call History Upgrading your System Software Managing Calls from the Web Administration InterfaceTroubleshooting Upgrade Failures Upgrade Error Codes Placing a Call from the Redial List Near End Video QualityPlacing a Call To place a call from the directory, follow these steps Placing a Call from the DirectoryManually Dialing a Number from the Main Screen Manually Dialing a Video Number Answering or Rejecting a Call Manually Dialing a Voice Number Call Status Using System Do Not DisturbManaging a Call Caller ID Managing PIP Hiding or Showing User Interface ElementsManaging Audio Managing Video Layout Far End Video Near End Video Screen Layout Far End VideoNear End Video Far End Video Near End Video During a Ending a Call from the Call Manager Viewing Call StatisticsEnding a Call To hang up a call, press OK again to end the call Removing an Entry from the Redial List Managing the Redial ListLocking and Unlocking Entries in the Redial List Adding a Redial List Entry to the Directory Copying an Entry from the Corporate to the Local Directory Managing the DirectoryAdding an Entry to the Local Directory Removing an Entry from the Local Directory Editing an Entry in the Local Directory Adding an Entry to the Meetings Directory Navigation button overview Customizing OSD settingsMenu settings Supported Input Description Mode settings Please contact the service center Check the power cable is connected correctlyCheck the main power switch is turned on Check the input voltage is correct You can not make a call Configure your display againConnected. Check the signal cable and try again Appears on the screen Specifications Diagnostic logging 280 x720p @ 25 to 30 fps ResolutionDo Not Disturb mode Directory Service H.350 Admin and User level password Save, Lock, Remove Redial List featuresBackup and Restore capability Ability to disable HTTP, SSH and Telnet services Warranty Card Appendix