Rear of the VCS | LG Electronics AVS2400 instruction

Preparation 11

NOTE

OSD lock / unlock function

You can lock the current control settings, so that they cannot be inadvertently changed.

1.Press and hold the MENU button for several seconds. The message “OSD LOCKED” should appear.

2.You can unlock the OSD controls at any time by holding the MENU button for several seconds. The message “OSD UNLOCKED” should appear.

IMonitor power button: Turns the monitor on and off. The camera and system power are not turned off by the monitor power button. You can turn the camera and system power off by using the Main power switch.

Rear of the VCS

J KLM N O

2

Preparation

PQ R S

JPower cord Inlet (AC IN): Connects the power plug.

KMain power switch: Turns the unit on and off. You must turn the unit on using the main power switch after connecting the power cable. You can use this button to reset the system.

LLAN port: Connects the LAN cable for this system.

MPC (LAN) port: Connects the LAN cable between the VCS and your PC.

NHDMI port: Connects the VCS and the PC with a HDMI cable.

OD-SUB port: Connects the VCS and the PC with the D-SUB cable.

PSpeaker set: Two speakers are built-in.

QMicrophone jack: Connects an external microphone.

RHeadphone jack: Connects an external speaker device.

SLOCK: Connects the Kensington security system cable between the VCS and a large object such as a desk.

Image 11

LG Electronics AVS2400 Rear of the VCS, OSD lock / unlock function, Power cord Inlet AC in Connects the power plug

Contents

Video Conference Monitor Regulatory Information FCC Part Safety Information Or moisture, does not operate normally, or has been dropped Disposal of your old applianceEEE Compliance with Directive. for Turkey only Lamps Contain Mercury, Dispose Properly On Installation On Safety Lifting and moving the VCS On CleaningOn Repacking On Disposal Contents Specifications Customizing OSD settingsMenu settings Mode settings Introduction Features Unpacking VCS Body Remote control and batteries Front of the VCS Overview OSD lock / unlock function Power cord Inlet AC in Connects the power plugRear of the VCS Battery Installation Remote Control Attaching the stand Connections Disassembling the stand Using the Kensington security system optional Hdmi connection Connecting to a PCVideo Audio SUB connection Connecting Power Connecting Network Connecting a Microphone Connecting Headphones Attaching the back cover Adjusting the angle of the Monitor and camera Default administrator password is 1 2 3 Initial settings for VCS Set the options of the Identification menu and press Set the options of the Network menu and press button Installation Main screen overview Icon Accessing the System Menu Access User Preferences from which you can do the following User Preferences setup Administration from a Web Browser Administrator PreferencesAccessing Administrative Features Administration Using the Remote Control Installation Configuring Call Preferences Admission Control Configuring Security PreferencesControlling Remote Administration Setting the User Password Changing the Administrator Password Configuring Audio Codec Order Viewing Recent Configuration ChangesConfiguring Audio Behaviors Selecting the Active Microphone Administrator Preferences AudioTesting Primary Audio Output Adjusting Audio Levels Specifying Network Speed Configuring Network UsageSpecifying a Locally Configured IP Address Specifying the Hostname and Domain Name Service DNS Servers Enabling IPv6 Addressing Specifying a Vlan TagSpecifying an NTP Server Restricting Reserved Ports Enabling Network Address Translation NAT Call Type Number of Required UDP Ports Configuring Quality of ServiceConfiguring LifeSize Transit Preferences Call Type Number of Required UDP and TCP Ports Populating the Corporate Directory Disabling Access to the Local Directory Server and receive data was successful Ldap preferences are not configuredConfiguring Auto Discovery Reading from an Ldap Server Enabling Telepresence Configuring Communications Preferences Virtual Link Data Sharing Configuring Dialing OptionsSpecifying H.323 Settings Receiving Presentations Enabling H.460 Support for H.323 Calls Configuring SIP Settings Video Layout Preferences Configuring Appearance Preferences Controlling the Camera Use by Far End Users Configuring Video BehaviorsConfiguring Display Preferences Locking the Camera Presets Selecting Priority of Quality Metrics for Source Video Configuring System SettingsAdjusting Video Encoder Quality Adjusting the MTU of Video Packets Identifying the System Rebooting the System automaticallyManually Setting System Date and Time Navigate to Administrator Preferences System License Keys Hours to complete Installing a License Key ManuallyNavigate to Preferences System License Keys Restoring Default Settings Using Diagnostics Preferences and Tools Rebooting the System Using Camera Diagnostic PreferencesUsing Network Utilities Do Not Disturb Saving and Restoring a System Configuration Exclusive Web Administration FeaturesUsing Advanced Directory Features Upgrading System Software Copying Screen Text to the ClipboardDownloading Call History Upgrading your System Software Managing Calls from the Web Administration InterfaceTroubleshooting Upgrade Failures Upgrade Error Codes Placing a Call from the Redial List Near End Video QualityPlacing a Call Manually Dialing a Video Number Placing a Call from the DirectoryManually Dialing a Number from the Main Screen To place a call from the directory, follow these steps Manually Dialing a Voice Number Answering or Rejecting a Call Caller ID Using System Do Not DisturbManaging a Call Call Status Managing Video Layout Hiding or Showing User Interface ElementsManaging Audio Managing PIP Near End Video During a Screen Layout Far End VideoNear End Video Far End Video Far End Video Near End Video To hang up a call, press OK again to end the call Viewing Call StatisticsEnding a Call Ending a Call from the Call Manager Adding a Redial List Entry to the Directory Managing the Redial ListLocking and Unlocking Entries in the Redial List Removing an Entry from the Redial List Removing an Entry from the Local Directory Managing the DirectoryAdding an Entry to the Local Directory Copying an Entry from the Corporate to the Local Directory Adding an Entry to the Meetings Directory Editing an Entry in the Local Directory Navigation button overview Customizing OSD settingsMenu settings Supported Input Description Mode settings Check the input voltage is correct Check the power cable is connected correctlyCheck the main power switch is turned on Please contact the service center Appears on the screen Configure your display againConnected. Check the signal cable and try again You can not make a call Specifications Directory Service H.350 280 x720p @ 25 to 30 fps ResolutionDo Not Disturb mode Diagnostic logging Ability to disable HTTP, SSH and Telnet services Save, Lock, Remove Redial List featuresBackup and Restore capability Admin and User level password Warranty Card Appendix