Return to Section TOC
Return to Master TOC
INSTALLATION | ||||
GUN AND CABLE INSTALLATION |
| WARNING | ||
|
|
| ||
The Magnum 250L gun and cable provided with the |
| CYLINDER may explode if | ||
POWER MIG 255C is factory installed with a liner for |
| |||
| damaged. | |||
| ||||
| • Gas under pressure is explosive. Always keep | |||
in. (0.9 mm) contact tip. Install the 0.045 tip (also pro- |
| |||
| gas cylinders in an upright position and always | |||
vided) if this wire size is being used. |
|
| ||
|
| keep chained to undercarriage or stationary | ||
|
|
| support. See American National Standard Z- | |
WARNING |
|
| 49.1, “Safety in Welding and Cutting” pub- | |
|
| lished by the American Welding Society. | ||
Turn the welder power switch off before installing | ||||
3. Stand to one side away from the outlet and open | ||||
gun and cable. |
| |||
| the cylinder valve for an instant. This blows away | |||
any dust or dirt which may have accumulated in | ||||
|
| |||
1. Lay the cable out straight. |
| the valve outlet. | ||
|
|
| ||
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
2.Unscrew knurled screw on the drive unit front end (inside wire feed compartment) until tip of screw no longer protrudes into gun opening as seen from front of machine.
3.Insert the male end of gun cable into the female casting through opening in front panel. Make sure connector is fully inserted and tighten knurled screw.
4.Connect the gun trigger connector from the gun and cable to the mating receptacle inside the compartment located above the gun connection made in item 3 above. Make sure that the key- ways are aligned, insert and tighten retaining ring.
SHIELDING GAS
(For Gas Metal Arc Welding Processes)
Customer must provide cylinder of appropriate type shielding gas for the process being used.
A gas flow regulator, for CO2 or Argon blend gas, and an inlet gas hose are factory provided with the POWER MIG 255C. Install the shielding gas supply as follows:
1.Set gas cylinder on rear platform of POWER MIG 255C. Hook chain in place to secure cylinder to rear of welder.
2.Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. Remove dust and dirt with a clean cloth.
DO NOT ATTACH THE REGULATOR IF OIL, GREASE OR DAMAGE IS PRESENT! Inform your gas supplier of this condition. Oil or grease in the presence of high pressure oxygen is explosive.
WARNING
Be sure to keep your face away from the valve out- let when “cracking” the valve.
4.Attach the flow regulator to the cylinder valve and tighten the union nut(s) securely with a wrench.
NOTE: If connecting to 100% CO2 cylinder, insert regulator adapter between regulator and cylinder valve. If adapter is equipped with a plastic washer, be sure it is seated for connection to the CO2 cylinder.
5.Attach one end of the inlet gas hose to the outlet fitting of the flow regulator, the other end to the POWER MIG 255C rear fitting, and tighten the union nuts securely with a wrench.
6.Before opening the cylinder valve, turn the regu- lator adjusting knob counterclockwise until the adjusting spring pressure is released.
7.Standing to one side, open the cylinder valve slowly a fraction of a turn. When the cylinder pres- sure gauge pointer stops moving, open the valve fully.
WARNING
Never stand directly in front of or behind the flow regulator when opening the cylinder valve. Always stand to one side.
8.The flow regulator is adjustable. Adjust it to the flow rate recommended for the procedure and process being used before making the weld.
AUXILIARY POWER RECEPTACLES
(For 208/230V Models only)
This machine is equipped with 15Amp 120V receptacle with 15Amp Circuit Breaker. The receptacle is UL and CSA approved.
POWER MIG 255C
