Lincoln Electric SVM170-A service manual Procedure for Changing, Drive and Idle Roll Sets

Section TOC

Master TOC

B-5	OPERATION		B-5
PROCEDURE FOR CHANGING	5.	Rotate the spindle and adapter so the retaining spring is
DRIVE AND IDLE ROLL SETS		at the 12 o'clock position.
1. Turn off the power source.	6.	Position the Readi-Reel so that it will rotate in a direction
		when feeding so as to be de- reeled from top of the coil.

Return to

Return to Section TOC

Return to Section TOC

Return to

Return to Master TOC

Return to Master TOC

2.Release the pressure on the idle roll by swinging the adjustable pressure arm down toward the back of the machine. Lift the cast idle roll assembly and allow it to sit in an upright position.

3.Remove the outside wire guide retaining plate by loosening the two large knurled screws.

4.Twist the drive roll retaining mechanism to the unlocked position as shown below and remove the drive roll. (See Figure B.2)

FIGURE B.2

5.Remove the inside wire guide plate.

6.Replace the drive and idle rolls and inside wire guide with a set marked for the new wire size. NOTE: Be sure that the gun liner and contact tip are also sized to match the selected wire size.

7.Manually feed the wire from the wire reel, over the drive roll groove and through the wire guide and then into the brass bushing of the gun and cable assembly.

8.Replace the outside wire guide retaining plate by tightening the two large knurled screws. Reposition the adjustable pressure arm to its original position to apply pressure. Adjust pressure as necessary.

7.Set one of the Readi-Reel inside cage wires on the slot in the retaining spring tab.

8.Lower the Readi-Reel to depress the retaining spring and align the other inside cage wires with the grooves in the molded adapter.

9.Slide cage all the way onto the adapter until the retaining spring "pops up" fully.

WARNING

CHECK TO BE SURE THE RETAINING SPRING HAS FULLY RETURNED TO THE LOCKING POSITION AND HAS SECURELY LOCKED THE READI-REEL CAGE IN PLACE. RETAINING SPRING MUST REST ON THE CAGE, NOT THE WELDING ELECTRODE.

---------------------------------------------------------------

10.To remove Readi-Reel from Adapter, depress retaining spring tab with thumb while pulling the Readi-Reel cage from the molded adapter with both hands. Do not remove adapter from spindle.

2 IN. O.D. ADAPTER

SPINDLE RETAINING SPRING

RETAINING

COLLAR

BRAKE

HOLDING

PIN GROOVES

READI-REEL

INSIDE

CAGE RELEASE

WIRES BAR

To Mount 10 to 44 Lb. (4.5-20 kg) Spools (12"/300 mm Diameter) or 14Lb.(6 Kg) Innershield Coils:

Return to Section TOC

Return to Master TOC

WIRE REEL LOADING - READI REELS, SPOOLS OR COILS

To Mount a 30 Lb. (14 kg) Readi-Reel Package (Using the Molded Plastic K363-P Readi-Reel Adapter:)

1.Open the Wire Drive Compartment Door

2.Depress the Release Bar on the Retaining Collar and remove it from the spindle.

3.Place the Optional Adapter on the spindle

4.Re-install the Retaining Collar. Make sure that the Release Bar "pops up" and that the collar retainers fully engage the retaining ring groove on the spindle.

(For 13-14 lb. (6 Kg) Innershield coils, a K435 Coil Adapter must be used).

(For 10 lb.(4.5 Kg) 8 inch(203mm) diameter spools, a K468 spindle adapter must be used).

1.Open the Wire Drive Compartment Door

2.Depress the Release Bar on the Retaining Collar and remove it from the spindle.

3.Place the spool on the spindle making certain the spindle brake pin enters one of the holes in the back side of the spool (Note: an arrow mark on the spin- dle lines up with the brake holding pin to assist in lin- ing up a hole). Be certain the wire comes off the reel in a direction so as to de-reel from the top of the coil.

4.Re-install the Retaining Collar. Make sure that the Release Bar "pops up" and that the collar retainers fully engage the retaining ring groove on the spindle.

POWER MIG 255C