Lincoln Electric SVM170-A Drive Roll Kits, Alternative Magnum Gmaw Gun And Cable Assemblies

Section TOC

Master TOC

C-2	ACCESSORIES	C-2
DRIVE ROLL KITS	MAGNUM GUN CONNECTION KIT
Refer to Table C.1 for various drive roll kits that are available for (Optional K466-6)

the POWER MIG. All items in Bold are supplied standard with the	Using the optional K466-6 Magnum Connection kit for
POWER MIG.
	the POWER MIG permits use of standard Magnum
	200, 300 or 400 gun and cable assemblies.

Return to

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to

Return to Master TOC

Return to Master TOC

Return to Master TOC

TABLE C.1 — AVAILABLE DRIVE ROLL KITS.

Electrode Type	Wire Size	Drive Roll Kit
Solid Steel	.023”-.030” (0.6-0.8 mm)	KP1696-030S
(Includes	.035” (0.9 mm)	KP1696-035S
	.045” (1.2 mm)	KP1696-045S
Stainless
Steel)	.035-.045 (0.9-1.2mm)	KP1696-1
	.040 (1.01)	KP1696-2
Cored	.035” (0.9 mm)	KP1697-035C
	.045” (1.2 mm)	KP1697-045C
Aluminum	3/64” (1.2 mm)	KP1695-3/64A

3/64" (1.2 mm) ALUMINUM FEEDING KIT (K1703-1)

This kit helps push feeding aluminum through standard machine feeder and gun. It provides gun and wire drive conversion parts to weld with 3/64" (1.2 mm) aluminum wire. 5356 alloy aluminum wire is recommended for best push feeding peformance.

Kit includes drive rolls and wire guide plate for the wire drive, liner and two contact tips for the gun, along with installation instructions.

K2378-1 Canvas Cover

K468 Spindle Adapter - for 8” (203.2mm) O.D. spool.

K363P READI-REEL ADAPTER

The K363P Readi-Reel Adapter mounts to the 2" spindle. It is needed to mount the 22-30 lb. Readi-Reels.

DUAL CYLINDER MOUNTING KIT (K1702-1)

Permits stable side-by-side mounting of two full size (9" dia. x 5' high) gas cylinders with "no lift" loading. Simple installa- tion and easy instructions provided. Includes upper and lower cylinder supports, wheel axles and mounting hardware.

ALTERNATIVE MAGNUM GMAW GUN AND CABLE ASSEMBLIES

The following Magnum 250L gun and cable assemblies are separately available for use with the POWER MIG 255C. Each is rated 200 amps 60% duty cycle (or 250 amps 40% duty) and is equipped with the integrated connector, twist-lock trigger connector, fixed nozzle and insulator, and includes a liner, diffuser, and contact tips for the wire sizes specified:

		English Wire	Metric Wire
Length	Part No.	Size1	Size
12' (3.6 m)	K533-7	.035 – .045"	0.9 – 1.2 mm
15' (4.5 m)	K533-3

TIMER KIT INSTALLATION (Optional K1701-1)

The timer kit adds selectable 4-step trigger interlock, spot and Run-In functions and manual adjustment of burnback time. Install as follows, or per the instructions included with the kit:

WARNING

Remove all input power to the POWER MIG 255C before proceeding.

-----------------------------------------------------------------------

1.Verify that the following items have been included in the kit:

A.Timer board/with harness and panel assembly .

B.Two screws.

2.Prepare for kit installation by turning the power switch off and disconnecting power from the machine.

3.Remove the lower cover panel from the front of the machine by removing the two screws which secure

4.Attach the black rectangular 10-pin plug connector on the timer kit wiring harness to the black mating receptacle connector located on the P.C. board. Be sure that the latch on the connec-tor is aligned with the one on the board and insert it until the latch engages.

5.Align the timer panel for installation and carefully insert the printed circuit board and wiring harness through the opening. Make sure the wiring harness is not pinched between panels or between printed circuit board and front panel cover.

6.Secure the timer assembly with either the two supplied screws or with the original screws. The installation is now complete. Refer to the following section for operating instructions.

POWER MIG 255C