As you change parameters, they will not actually be incorporated into your running system until you execute a Store New Parameters (&W) command.
Table 4-3. Configuration Procedure
Step |
|
|
|
|
| Procedure |
|
|
|
|
| |||
Async Channels |
|
|
|
|
|
|
|
|
|
|
| |||
| 14 Execute the parameter display command to display the current channel | parameter status for your local | ||||||||||||
|
|
| MultiMux by entering the following: |
|
|
|
|
|
| |||||
|
|
|
|
| ATL (hit Return) |
|
|
|
|
|
|
| ||
| The following will be displayed on your supervisory console for a MultiMux MMV1616: | |||||||||||||
|
|
|
|
|
|
| Local Channel Parameters/ Node # 00 |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| STP |
| FLOW | ENQ/ |
|
| PASS | PASS DEST DEST | LINK |
| ||
CHN SPD WD BIT PAR | CTRL | ACK | ECHO | PACE | EIA | XON | CHN NODE | A/B |
| |||||
01 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 01 | 01 | A |
|
02 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 02 | 01 | A |
|
03 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 03 | 01 | A |
|
04 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 04 | 01 | A |
|
05 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 05 | 01 | A |
|
06 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 06 | 01 | A |
|
07 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 07 | 01 | A |
|
08 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 08 | 01 | A |
|
09 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 09 | 01 | A |
|
10 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 10 | 01 | A |
|
11 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 11 | 01 | A |
|
12 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 12 | 01 | A |
|
13 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 13 | 01 | A |
|
14 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 14 | 01 | A |
|
15 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 15 | 01 | A |
|
16 | 19200 | 8 | 1 | NONE | CTS | OFF | OFF | OFF | OFF | OFF | 16 | 01 | A |
|
15Based on the listed conditions for each channel, reconfigure the parameters to match your actual channel requirements by entering commands as described in Chapter 5.
As you change operational parameters, they will not actually be incorporated into your running system until you execute a Store New Parameters (&W) command.
Table 4-3. Configuration Procedure
Step | Procedure |
Voice/Fax Channels
16To display the current Voice/Fax channel parameters, enter the following: ATVL (hit Return)
The following will be displayed on your supervisory console for the Voice/Fax channels:
LOCAL VOICE/FAX PARAMETERS CHANNEL 1 LOCAL VOICE/FAX PARAMETERS CHANNEL 2
PARAMETER | STATUS | PARAMETER | STATUS |
DESTINATION CHANNEL: | 01 | DESTINATION CHANNEL: | 02 |
DESTINATION NODE: | 02 | DESTINATION NODE: | 02 |
LINK A/B/D: | A | LINK A/B/D: | A |
DIGITIZING RATE: | 16000 | DIGITIZING RATE: | 16000 |
OUTPUT LEVEL ATTEN.: | 12 | OUTPUT LEVEL ATTEN.: | 12 |
INPUT LEVEL GAIN: | 03 | INPUT LEVEL GAIN: | 03 |
SILENCE SUPPRESSION: | 00 | SILENCE SUPPRESSION: | 00 |
LOCAL INTERFACE TYPE: | FXS | LOCAL INTERFACE TYPE: | FXS |
GROUND/LOOP START (FXS): | LOOP | GROUND/LOOP START (FXS): | LOOP |
2 OR 4 WIRE (E&M): | 2 WIRE | 2 OR 4 WIRE (E&M): | 2 WIRE |
DIALTONE/WINK (E&M): | N/A | DIALTONE/WINK (E&M): | N/A |
WINK TIMER (E&M): | N/A | WINK TIMER (E&M): | N/A |
REMOTE INTERFACE TYPE: | FXS | REMOTE INTERFACE TYPE: | FXS |
GROUND/LOOP START (FXS): | LOOP | GROUND/LOOP START (FXS): | LOOP |
2 OR 4 WIRE (E&M): | 2 WIRE | 2 OR 4 WIRE (E&M): | 2 WIRE |
DIALTONE/WINK (E&M): | N/A | DIALTONE/WINK (E&M): | N/A |
