Multi-Tech Systems MMV1600 View Active, Configuration displays, User Profiles, Store Active, W0-1

	13	DATA	Command modem connected as data
modem during auto answer.
	You can also choose to completely eliminate the display of all of the					Result Codes.
This is accomplished by executing the Q command.
View Active	The View Active Configuration and User Profiles &V command					Configuration displays the
commands and S-Register settings along with the				and User Profiles	stored telephone numbers. A typical
example of active and		stored profiles and stored telephone numbers are as follows:
&V	ACTIVE PROFILE:
	B1 E1 H0 Q0 V1 X4 Y0 &G0 &P0 &T4 &Y
	S00:000 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:030					S08:002 S09:006
S10:014 S12:050 S14:AAH S16:00H S18:000				S21:00H S22:76H S23:07H S25:005 S26:001S027:40H S28:00H
	STORED PROFILE 0:
	B1 E1 H0 Q0 V1 X4 Y0 &G0 &P0 &T4
	S00:000 S14:AAH S18:000 S21:00H S22:76H S23:15H S25:005					S26:001S027:40H
S28:00H
	STORED PROFILE 1:
	B1 E1 H0 Q0 V1 X4 Y0 &G0 &P0 &T4
	S00:000 S14:AAH S18:000 S21:00H S22:76H S23:17H S25:005					S26:001S027:40H
S28:00H

TELEPHONE NUMBERS: &Z0= 18009722439 &Z1= 6127859875 &Z2=

&Z3=

Wait for Dial Tone The W command causes the command modem to wait up to a						specified time for the
dial tone to occur. The telephone number			W	is dialed immediately upon dial tone detection. The S-Register
S7 value determines the maximum wait time. If a busy signal is					detected instead of dial tone, the
command modem returns a		BUSY result code and goes On-Hook, abandoning subsequent
instructions on the command line. The factory default setting is					30 seconds
Store Active	The Store Active Profile &W command writes the storable					Profile parameters of the
active configuration to one of two profiles in				NVRAM. The current values of the following commands and
&W0-1	registers are stored:
	Commands: Bn, En, Qn, Vn, Xn, &Gn, &Pn, and &Yn
	S-Registers: S0, S14, S18, S21, S22, S23, S25, S26, S27, and S28
	The &W0 command stores the active profile in the NONVRAM					at location zero and
&W1 stores the active profile in location one.				&W0 is the factory default setting.
Result Code Set/	The Result Code Set/Call Progress (X ) command selects which					Call Progress	set of
responses and dialing functions are active in Command					mode. You can choose to have certain
responses suppressed,		X such as the speed of the connection, and whether or not dial tone					and
busy signal are detected. You can choose either the basic					result code set (i.e., the connect response with
no speed		indication of the called command modem) or the extended result
code set (i.e., connection response with speed indication) and					whether or not call progress is activated.
	The	ATX0 and ATX1 commands disable the call progress				functions (dial tone
and busy signal) and activates either the				basic or extended result codes. This call progress method is
referred to as dumb dialing where actual dial tones are not					detected, instead the command modem
relies on timed		pauses. The ATX0 enables the basic result codes while the ATX1
enables the extended result codes with call progress disabled on					both commands.
	The ATX2 through ATX4 commands determine whether or not					call progress is
activated and extended result codes are enabled				on each of these commands.
	The ATX2 command waits for a dial tone before dialing. The					connect response and
speed indication (e.g.,CONNECT xxxx			where as xxxx is the connect speed of 2400 bps) are enabled
upon detection of a dial tone. Busy signal is not detected.
	The ATX3 command causes the command modem to dial					blind(i.e., does not
wait for dial tone) and enable a BUSY result				code if a busy signal is detected.		This feature is useful because
	it allows the command modem to immediately abandon a call					rather than wait the
thrity seconds for a carrier signal that will				never come.