Multi-Tech Systems MMV1600 owner manual Remote Site

2.8 Configuration 7

Configuration 7 is the data/voice/fax configuration with two MultiMux MMV1608C/56/V multiplexers with single composite link connecting a minicomputer and a PBX E&M trunk at the local site to a group of remote terminals and printer on the data part of the network and a telephone and/or fax machine on the remote voice/fax channels. The E&M to FXS configuration is shown in Figure 2-7. In this configuration the data communications is set up per configuration 1.

This configuration has the MV2 Voice/Fax board installed in the MMV1608/56/V multiplexers for the voice over data communications. The local site has the MV2 Voice/Fax board connecting VOICE/FAX CHANNEL 1and/or 2 E&M connector(s) on the back panel of the local multiplexer to a PBX E&M trunk. At the remote site the MV2 Voice/Fax board is connecting VOICE/FAX CHANNEL 1 and/or 2 FXS connector(s) on the back panel of the remote multiplexer to a telephone and/or a fax machine on the second channel.

Terminal

Terminal	Printer	Asynchronous			Asynchronous
		Channel
			PDN		Channel
	Modem			MultiTech
				MultiMux 16
		MultiTech	Composite Link
		MultiMux 16
Terminal				Multiplexer
		Multiplexer			Minicomputer
	PC			Voice/Fax
Voice/Fax		Voice/Fax Channel 2 FXS		Channel 1 E&M	Voice/Fax
Channel 1					Channel 2 E&M
FXS

PSTN

Telephone Fax

Remote Site

(Node 2)

Trunk

Trunk

Trunk

Station

Station

PBX

Telephone

Local Site

(Node 1)

Figure 2-7. Configuration 7 (E&M I-V to FXS)

The local site is configured for an E&M configuration on both voice/fax channels using the V1LIE&M2D4 command for channel 1 and V2LIE&M2D4) command for channel 2 and setting the Remote Interface type for an FXS configuration using the V1RIFXS and or V2RIFXS commands depending on whether one or both of the remote voice/fax channels are used. The parameters for the local and remote voice/fax channels can be displayed using the VL (List the voice/ fax channel parameters) command. The voice/fax channel parameters are shown in Configuration 7 Voice/Fax Channel Parameters. The voice/fax channel parameters are described in Chapter 5 Commands of this manual.

LOCAL VOICE/FAX PARAMETERS CHANNEL1		LOCAL VOICE/FAX PARAMTERS CHANNEL 2
PARAMETER	STATUS	PARAMETER	STATUS
DESTINATION CHANNEL:	01	DESTINATION CHANNEL:	02
DESTINATION NODE:	02	DESTINATION NODE:	02
LINK A/B/D:	A	LINK A/B/D:	A
DIGITIZING RATE:	16000	DIGITIZING RATE:	16000
OUTPUT LEVEL ATTEN.:	14	OUTPUT LEVEL ATTEN.:	14
INPUT LEVEL GAIN:	05	INPUT LEVEL GAIN:	05
SILENCE SUPPRESSION:	00	SILENCE SUPPRESSION:	00
LOCAL INTERFACE TYPE:	E&M 2	LOCAL INTERFACE TYPE:	E&M 2
GROUND/LOOP START (FXS):	N/A	GROUND/LOOP START (FXS):	N/A
2 OR 4 WIRE (E&M):	4 WIRE	2 OR 4 WIRE (E&M):	4 WIRE
DIALTONE/WINK (E&M):	DIAL	DIALTONE/WINK (E&M):	DIAL
WINK TIMER (E&M)	N/A	WINK TIMER (E&M)	N/A
REMOTE INTERFACE TYPE:	FXS	REMOTE INTERFACE TYPE:	FXS
GROUND/LOOP START (FXS):	LOOP	GROUND/LOOP START (FXS):	LOOP
2 OR 4 WIRE (E&M):	2 WIRE	2 OR 4 WIRE (E&M):	2 WIRE
DIALTONE/WINK (E&M):	N/A	DIALTONE/WINK (E&M):	N/A