Configuring network protocol via the machine
You can set up TCP/IP network parameters, follow the steps listed below.
1.Make sure your machine is connected to the network with an
2.Make sure you have turned on the machine.
3.Press Menu on the control panel, until you see Network on the bottom line of the display.
4.Press OK to access the menu.
5.Press the left/right arrow until TCP/IP displays.
6.Press OK.
7.Press the left/right arrow until Static displays.
8.Press OK.
9.Press the left/right arrow until IP Address displays.
10.Press OK.
Enter a byte between 0 and 255 using the number keypad and press the left/right arrow to move between bytes.
Repeat this to complete the address from the 1st byte to the 4th byte.
11.When you have finished, press OK.
Repeat steps 9 and 10 to configure the other TCP/IP parameters: subnet mask and gateway address.
Contact the network administrator if you are not sure how to configure.
You can also set up the network settings through the network administration programs.
•SyncThru™ Web Admin Service:
internet access. Download this program from http:// solution.samsungprinter.com.
•SyncThru™ Web Service: Web server embedded on your network print server, which allows you to:
-Configure the network parameters necessary for the machine to connect to various network environments.
-Customize machine settings.
•SetIP: Utility program allowing you to select a network interface and manually configure the IP addresses for use with the TCP/IP protocol.
Using the SetIP program
This program is for the network IP setting using the MAC address which is the hardware serial number of the network printer card or interface. Especially, it is for the network administrator to set several network IPs at the same time.
Installing the program
1.Insert the driver CD provided along with your machine. When the driver CD runs automatically, close the window.
2.Start Windows Explorer and open the X drive. (X represents your CD- ROM drive.)
3.Double click Application > SetIP.
4.Open the folder of the language you plan to use.
5.Double click Setup.exe to install this program.
6.Follow the instructions in the window and complete the installation.
Starting the program
1.From the Windows Start menu, select All Programs > Samsung Network Printer Utilities > SetIP.
2.Select the name of your printer and click 
.
If you cannot find your printer name, click 
to refresh the list.
3.Enter the network card's MAC address, IP address, subnet mask, default gateway, and then click Apply.
If you do not know the network card's MAC address, print the machine's network information report. (See "Printing reports" on page 61.)
4.Click OK to confirm the settings.
5.Click Exit to close the SetIP program.
SYSTEM REQUIREMENTS
Before you begin, ensure that your system meets the following requirements:
Windows
Your machine supports the following Windows operating systems.
OPERATING | REQUIREMENT (RECOMMENDED) | ||
|
|
| |
SYSTEM | CPU | RAM | FREE HDD |
| SPACE | ||
|
|
| |
Windows 2000 | Pentium II 400 MHz | 64 MB | 600 MB |
| (Pentium III 933 MHz) | (128 MB) |
|
Windows XP | Pentium III 933 MHz | 128 MB | 1.5 GB |
| (Pentium IV 1 GHz) | (256 MB) |
|
Windows 2003 | Pentium III 933 MHz | 128 MB | 1.25 GB to |
Server | (Pentium IV 1 GHz) | (512 MB) | 2 GB |
Windows Vista | Pentium IV 3 GHz | 512 MB | 15 GB |
|
| (1024 |
|
|
| MB) |
|
|
|
|
|
• Internet Explorer 5.0 or higher is the minimum requirement for all Windows operating systems.
•Users who have an administrator right can install the software.
Macintosh
OPERATING |
| REQUIREMENT (RECOMMENDED) | ||
|
|
|
| |
SYSTEM |
| CPU | RAM | FREE HDD |
|
| SPACE | ||
|
|
|
| |
Mac OS X | • | Intel Processor | • 128 MB for a | 1 GB |
10.3 ~ 10.4 | • | Power PC G4 / |
| |
|
| G5 | based Mac (512 |
|
|
|
| MB). |
|
|
|
| • 512 MB for an |
|
|
|
|
| |
|
|
| (1 GB) |
|
|
|
|
|
|
Mac OS X 10.5 | • | Intel Processor | 512 MB (1 GB) | 1 GB |
| • | 867 MHz or |
|
|
|
| faster Power |
|
|
|
| PC G4 /G5 |
|
|
|
|
|
|
|
26 _Getting started
