Manuals / Nikon / Computer Equipment / Scanner

Nikon LS-2000 manual SCSI connection checklist, Setup, Safety Precautions

Models: LS-2000

1 47

Download 47 pages 52.86 Kb

Page 23

✔SCSI connection checklist

3. Setup

✔SCSI connection checklist

• Turn off the computer, the LS-2000, and all SCSI devices before connecting the scanner.

•Be sure that the devices at both ends of the SCSI chain are terminated. If the host computer is a Macintosh, the chain will already be terminated at the computer end. In the case of IBM PC/AT compatibles in a chain which contains external devices only, the chain should be terminated at the SCSI board. In the case of a chain which includes internal devices, you may need to remove termination from the board and terminate the last internal device.

•The maximum number of SCSI devices that can be connected in a single chain is eight, including the computer and any internal SCSI devices such as hard disks or CD-ROM drives.

•The total length of cabling in the SCSI chain should be no more than six meters (twenty feet). The longer the cabling, the less reliable the connection.

Safety Precautions

•Do not damage the SCSI cabling’s protective insulation. Do not forcibly tug or bend SCSI cables, place cables under heavy objects or expose them to heat or flame. When disconnecting cables, handle the cable by the connector, not by the cable itself. Should the insulation be damaged or the internal wiring exposed, replace the cable immediately.

•Do not handle SCSI cables or devices when your hands are wet.

Nikon LS-2000 35 mm Film Scanner User’s Guide

13

Image 23

Nikon LS-2000 manual SCSI connection checklist, Setup, Safety Precautions

Contents

Page Page 35 mm Film Scanner LS-2000Users Guide Symbol SymbolCautions Trademark InformationModifications CAUTIONSNotice for customers in Canada Notice for customers in European countriesDo not modify Safety PrecautionsKeep clean Do not disassembleDo not place foreign objects inside the scanner When not using for an extended periodWhen performing routine maintenance Nikon LS-200035 mm Film Scanner User’s Guide When transporting the scannerComply with copyright notices Cautions on certain copies and reproductionsSetup ContentsContents Parts and Accessories1. Overview 1. Overview1. Overview The chapters that follow provide a step-by-stepguide to installing your scanner and using Nikon Scan to scan 35 mm slides or strip film. The next chapter, Parts and Accessories, lists the things you should find packaged with your LS-2000and names the parts of the scanner. This is followed by “ Setup,” which guides you through the process of connecting your scanner to a computer and installing Nikon Scan. “ Scanning” outlines the steps involved in using Nikon Scan to scan slides and strip film. A separate reference section lists the controls available in Nikon Scan. We hope that you find this manual useful2.1What’s in the Box 2.Parts and Accessories2.Parts and Accessories 2.Parts and Accessories 2.2Parts of the LS-2000Step 1-Choosea location for the scanner 3. Setup3.1Setting up the LS-2000 3. Setup3. Setup When installing the scanner on its base3. Setup When installing the scanner on its sideStep 2-Removethe transport locking screws At voltages of AC 125V or less Step 3-Connectthe power cableSafety Precautions At voltages of more than ACDo not plug the power cord into 3. Setup3. Setup Step 4-Connectthe SCSI cableScanner last of several external devices When the scanner is the last device in the chain3. Setup Scanner only external device in chain3. Setup When the scanner is between other devicesSafety Precautions SCSI connection checklist3. Setup Nikon LS-200035 mm Film Scanner User’s Guide Step 5-Setthe scanner’s SCSI ID3. Setup Nikon LS-200035 mm Film Scanner User’s Guide 3. Setup3. Setup 3.2Software InstallationStep 1-Reviewthe system requirements MacintoshWindows Step 2-InstallAdobe Acrobat ReaderWindows 3. SetupMacintosh Step 3-InstallNikon Scan3. Setup Windows from disk provided by hardware3. Setup After turning on your computer, place the Nikon Scan CD in the CD-ROMdrive. The folder shown below will open on the desktop 3. SetupMacintosh Step 2-StartNikon Scan 4. Scanning4. Scanning Step 1-Turnon your computerInserting the MA-20SLIDE Step 3-Insertan adapter in the scanner4. Scanning Inserting the SA-20STRIP FILM Cautions4. Scanning 4. Scanning Step 4-InsertfilmCautions Step 5—Choosea film typeStep 6-Choosea color space 4. Scanning4. Scanning Step 7—Choosea thumbnail SA-20Step 8-Performa preview scan 4. Scanning Step 10-Autocontrast adjustmentStep 9-Selecta crop 4. Scanning Step 11-Removedust and scratches4. Scanning Step 13-Scanthe selected cropStep 14-Scanadditional images Once the scan window has been re-opened,the current slide or film strip can be previewed and a new crop selected as outlined in steps 5 through 12, or the current film can be ejected and new film inserted and previewed. To eject a slide from the slide-mountadapter, press the eject button and then pull the slide the rest of the way out with your fingers 4. ScanningAppendix Nikon Scan Controls Appendix Nikon Scan ControlsMenus, Tabs, and Information Displays Appendix Nikon Scan Controls ButtonsAppendix Nikon Scan Controls Control DrawersThe Scan-SizeDrawer The Scanner Extras DrawerAppendix Nikon Scan Controls The Curves-and-LevelsDrawerThe Color-BalanceDrawer Color management PreferencesAppendix Nikon Scan Controls GammaERKLÄRUNG ÜBER EG-NORMENGERECHTHEIT EC DECLARATION OF CONFORMITYDECLARATION DE CONFORMITÉ DE LA CEE DECLARACIÓN DE CONFORMIDAD DE LA CEE