Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks 1000BASE-XD, 8100 manual Passport 8148TX 48-Port I/O Module

Models: 1000BASE-XD 8100

1 100

Download 100 pages 29.82 Kb

Page 31

Passport 8148TX 48-Port I/O Module

About the Passport 8100 Modules

Passport 8148TX 48-Port I/O Module

The Passport 8148TX module provides 48 autonegotiating 10/100 Mb/s ports

(Figure 1-5). Each port can operate in full- or half-duplex mode. Autonegotiation circuitry automatically negotiates the highest possible data rate and the duplex operation possible with the attached device, if the attached device supports IEEE 802.3u autonegotiation.

9672EA

Figure 1-5. Passport 8148TX Edge Switch Module

The port connectors are modular RJ-45 connectors with MDI-X wiring. This port can be connected to an MDI port (for example, a workstation or server) using a straight-through cable.

The Passport 8108TX module uses 10BASE-T/100BASE-TX RJ-45 port connectors to connect to 10 Mb/s or 100 Mb/s Ethernet segments or nodes.

Note: For 10 Mb/s connections, you can use Category 3, 4, or 5 copper unshielded twisted pair (UTP) cable. Use only Category 5 UTP cable to connect ports that will operate at 100 Mb/s.

Refer to Appendix A, “Technical Specifications,” for more information about the RJ-45 port connectors.

204515-C

1-11

Image 31

Nortel Networks 1000BASE-XD, 8100 manual Passport 8148TX 48-Port I/O Module, 5. Passport 8148TX Edge Switch Module

Contents

Part No. 204515-C April 4401 Great America Parkway Santa Clara, CA Using the Passport 8100 ModulesUSA Requirements Only Copyright 2000 Nortel NetworksTrademarks Statement of ConditionsNortel Networks NA Inc. Software License Agreement Japan/Nippon Requirements OnlyTaiwan Requirements Canada Requirements Only2. Restrictions on use reservation of rights. The Software and user manuals are protected under copyright laws. Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including any revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble, use for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user manuals or any copy, in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or transfer the Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’ and its licensors’ confidential and proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise disclose to any third party the Software, or any information about the operation, design, performance, or implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors however, Licensee may grant permission to its consultants, subcontractors, and agents to use the Software at Licensee’s facility, provided they have agreed to use the Software only in accordance with the terms of this license Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such intended examination of the Software and may procure support and assistance from Nortel Networks 204515-C About the Passport 8100 Modules ContentsPreface ChapterChapter Chapter Installing a Passport 8100 ModuleBasic Switch Configuration TroubleshootingAppendix B Appendix A Technical SpecificationsLEDs Appendix E RFCs and Standards Index Installing GBICsAppendix C Media Dependent Adapters Appendix DFigures Figure C-1. 1000BASE-SX Shortwave Gigabit MDA Front Panels Tables 204515-C Before You Begin Prefaceitalic text Text Conventionsarguments. Enter only one of the choices. Do not type the Related PublicationsInstalling the Passport 8001PS AC Power Supply part number 204519-B Technical Solutions Center How to Get HelpTelephone Number Page Chapter About the Passport 8100 Modules Features IEEE 802.1Q port-based virtual LANs VLANs IEEE 802.1p prioritization Passport 8190SM Management Module Ethernet Management Port PCMCIA Card Slot DTE/DCE SwitchReset Button Serial PortsFigure 1-2. LEDs on the Passport 8190SM Module LEDsPassport 8132TX 32-Port I/O Module 10BASE-T/100BASE-TX Port ConnectorsComm Port MDA SlotFigure 1-4. LEDs on the Passport 8132TX Module LEDs1 = Module LEDs 2 = Port Speed LEDs 3 = Port Link/Activity LEDs Figure 1-5. Passport 8148TX Edge Switch Module Passport 8148TX 48-Port I/O ModuleLEDs Passport 8108GBIC 8-Port I/O ModuleFigure 1-8. LEDs on the Passport 8108GB Module Redundancy FeaturesLEDs Figure 1-7. Passport 8108GBIC ModuleRedundant Passport 8190SM Modules Redundant Power SuppliesFailure of the power supply module Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Safety and Environmental Precautions Chassis Configuration RequirementsTo install a module in a Passport 8000 Series chassis Installing a Module204515-C Using the Passport 8100 ModulesFigure 2-4. Seating the Backplane Connectors Figure 2-3. Inserting a ModuleTurning On the Chassis Power Module Connecting CablesUsing the Passport 8100 Modules ConnectorFigure 2-6. Routing Network Cables Replacing Modules1. Disconnect all network cables from the module to be removed Chapter Basic Switch Configuration Specifying Port Numbers Basic Switch Configuration Booting the SwitchAccess Levels and Default Login Values Logging On to the System1. Specify the system name using the command Setting System IdentificationAssigning an IP Address to the Management Port Use the following command3. Enable or disable Web access using the commands Setting System Security1. Change CLI users and passwords using the following commands 2. Change SNMP community strings using the command2. Enable or disable Telnet access using the command 4. Change Web passwords using the command1. Confirm that all ports are in the default VLAN using the command Switch Configuration2. To assign an IP address for management, use the command 4. To save the configuration, enter 3. Specify a default gateway address/default routePage Normal Power-Up Sequence Chapter TroubleshootingFigure 4-1. DCE/DTE Switch on the Passport 8190SM Module Failure to Get a Login Prompt from the Console PortLED Indications of Problems Failure of Management Software to Recognize I/O ModulesProbable Cause TroubleshootingTable 4-1. LED Indications of Problems SymptomCabling Port Connection ProblemsAutonegotiation Modes Port Interface Addresses Installation-Related IssuesPage General Specifications Appendix A Technical SpecificationsSafety Agency Approvals Using the Passport 8100 ModulesEnvironmental Specifications Performance Specifications 64-byte packetsElectrical Specifications Passport 8190SM Switch Management ModuleTechnical Specifications Physical SpecificationsConsole Serial Port Management PortTable A-1. Pin Assignments in the Passport 8190SM Management Port DTE-to-DCE Pin Assignments Modem Serial PortTable A-2. Pin Assignments in the Passport 8190SM Console Port Table A-3Physical Specifications Data Port ConnectorsPassport 8132TX Module Using the Passport 8100 Modules450-1LR MDA, 450-1LX MDA Comm Port ConnectorMDAs 450-1SR MDA, 450-1SX MDAPhysical Specifications Port ConnectorsPassport 8148TX Module Using the Passport 8100 ModulesPhysical Specifications Passport 8108GBIC ModuleGBICs Technical SpecificationsCable Specifications 1000BASE-SX GBIC1000BASE-LX GBIC Using the Passport 8100 ModulesCable Specifications 1000BASE-XD GBIC1000BASE-ZX GBIC Technical SpecificationsFigure A-1. MDI-X to MDI Cable Connections MDI and MDI-X ConnectionsFigure A-2. MDI-X to MDI-X Cable Connections Declaration of ConformityPage Passport 8132TX and 8148TX I/O Modules page B-3 Appendix B LEDsPassport 8190SM Switch Management Module Passport 8190SM Switch Management Module this pageLabel Using the Passport 8100 ModulesTable B-1 LED Operation on the Passport 8190SM ModuleFigure B-2. LEDs on the Passport 8132TX and 8148TX Modules Passport 8132TX and 8148TX I/O ModulesPort LEDs on the Passport 8132TX and 8148TX Modules Passport 8108GBIC ModuleTable B-2. Module LEDs on the Passport 8132TX and 8148TX Modules Table B-3Module LEDs on the Passport 8108GBIC Module LEDsFigure B-3. LEDs on the Passport 8108GBIC Module Table B-4Page Appendix C Media Dependent Adapters 450 Series MDAs 1000BASE-SX MDA LEDs Media Dependent AdaptersFigure C-2. 1000BASE-LX Longwave Gigabit MDA Front Panels Table C-11000BASE-LX MDA LEDs 8100-4TX MDAUsing the Passport 8100 Modules Table C-28100 Series Fiber MDAs 8100 Series MDA LEDs Using the Passport 8100 ModulesFigure C-4. 8100 Series MDA Front Panels Table C-4Installing an MDA 8. Tighten the module retaining screws Appendix D Installing GBICs 3. Press on the front of the GBIC until it snaps into place Installing a GBIC1. Remove the GBIC from its protective packaging 2. Insert the GBIC into the slot on the module Figure D-2Figure D-3. Removing a GBIC To remove an installed GBICPage Appendix E RFCs and Standards Page Numbers IndexIndex-1 Index-2 Index-3 Index-4