Replacing Modules | Nortel Networks 1000BASE-XD, 8100 specs

Installing a Passport 8100 Module

Nortel Networks recommends that you route all network cables through the supplied cable management brackets (Figure 2-6).

9573FA

Figure 2-6. Routing Network Cables

Replacing Modules

Any of the Passport 8100 modules can be removed from an operating switch chassis without turning off the chassis power.

If you insert a module into the same slot and chassis where the same type of module was previously installed, the previous configuration is maintained for that module in that slot. In all other cases, a module inserted into a Passport 8000 series chassis is reset to factory defaults.

If you remove the switch management module (for example, to replace it), the switch continues switching for up to 2 minutes. Then it reboots using the configuration settings on the backup switch management module, if one is present. If no backup switch management is present, after 2 minutes all ports go to blocking mode.

204515-C

2-7

Image 43

Nortel Networks 1000BASE-XD, 8100 manual Replacing Modules, Routing Network Cables

Contents

Using the Passport 8100 Modules EC Declaration of Conformity EN 55 022 Statement Bureau of Standards, Metrology and Inspection Bsmi Statement Voluntary Control Council for Interference Vcci Statement 204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Before You Begin Preface Italic text Text Conventions Related Publications Xviii Technical Solutions Center Telephone Number How to Get HelpPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Management Module Passport 8190SM Switch Management Module Ethernet Management Port Pcmcia Card Slot DTE/DCE SwitchReset Button Serial Ports LEDs on the Passport 8190SM Module LEDs Passport 8132TX 32-Port I/O Module 10BASE-T/100BASE-TX Port Connectors Comm Port MDA Slot LEDs on the Passport 8132TX Module Passport 8148TX 48-Port I/O Module Passport 8148TX Edge Switch Module LEDs on the Passport 8148TX Module Passport 8108GBIC 8-Port I/O Module Passport 8108GBIC Module Redundancy Features Redundant Passport 8190SM Modules Redundant Power Supplies Chassis Number Hot-Swap One? Modules Power Supplies Power Supply Hot-Swapping Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Safety and Environmental Precautions Chassis Configuration Requirements Removing a Filler Panel Installing a Module Slide the module into the slot Figure Securing the Module in the Chassis Turning On the Chassis Power Connecting Cables Routing Network Cables Replacing Modules To replace a module Chapter Basic Switch Configuration Port Numbers on High-Density Modules Specifying Port Numbers Booting the Switch Access Level Description Default Login Password Access Levels and Default Login ValuesLogging On to the System Assigning an IP Address to the Management Port Setting System Identification Change CLI users and passwords using the following commands Setting System Security Change Web passwords using the command To assign an IP address for management, use the command Switch Configuration Specify a default gateway address/default route Page Normal Power-Up Sequence Chapter Troubleshooting LED Indications of Problems Failure to Get a Login Prompt from the Console PortFailure of Management Software to Recognize I/O Modules Symptom Probable Cause Corrective Action LED Indications of Problems Cabling Port Connection Problems Autonegotiation Modes Port Interface Use the CLI to disable autonegotiation for the suspect port Addresses Installation-Related IssuesPage General Specifications Appendix a Technical SpecificationsStandards Supported Data Rate and Encoding Environmental SpecificationsPerformance Specifications 64-byte packets Safety Agency Approvals Passport 8190SM Switch Management Module Management Port Connector Pin Number SignalConsole Serial Port Table A-3 DTE-to-DCE Pin Assignments Modem Serial Port Passport 8132TX Module Data Port ConnectorsConnector Type Cable Specifications 450-1LR MDA, 450-1LX MDA Comm Port ConnectorMDAs 450-1SR MDA, 450-1SX MDA Passport 8148TX Module Port ConnectorsTable A-5. Passport 8148TX Port Pinouts GBICs Passport 8108GBIC Module 1000BASE-SX Gbic Optical Specifications 1000BASE-XD Gbic Figure A-1. MDI-X to MDI Cable Connections MDI and MDI-X Connections Figure A-2. MDI-X to MDI-X Cable Connections Declaration of ConformityPage Figure B-1. LEDs on the Passport 8190SM Module Appendix B LEDs Label Color/State Meaning Table B-1 LED Operation on the Passport 8190SM Module Figure B-2. LEDs on the Passport 8132TX and 8148TX Modules Passport 8132TX and 8148TX I/O Modules Color/State Meaning LED Table B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Series MDAs Label Type Color/State Meaning Table C-1 1000BASE-SX MDA LEDs Table C-2 1000BASE-LX MDA LEDs 8100-4TX MDA Table C-3 8100-4TX MDA LEDs Series Fiber MDAs Table C-4 Series MDA LEDs Figure C-4 Series MDA Front Panels Figure C-5. Installing an MDA Installing an MDA Using the Passport 8100 Modules Figure D-1. Types of GBICs Appendix D Installing GBICs Figure D-2. Installing a Gbic Installing a Gbic To remove an installed Gbic Page Appendix E RFCs and Standards Page Numbers Index Index-2 Index-3 Index-4