Management Port, Console Serial Port | Nortel Networks 8100 instruction

Using the Passport 8100 Modules

Management Port

The Management port is a 10/100 Mb/s Ethernet port implemented on an RJ-45 connector wired as an MDI connection. Table A-1 shows the pin assignments for this connector.

Table A-1. Pin Assignments in the Passport 8190SM Management Port

Connector

Pin Number

Signal

12345678

8020EA

1	Output transmit data + (TX+)
2	Output transmit data - (TX-)
3	Input receive data + (RX+)
6	Input receive data - (RX-)
4, 5, 7, 8	Not used

Console Serial Port

The Console serial port is implemented as a DB-9 connector. This port can operate as a data terminal equipment (DTE) or data communication equipment (DCE) device. Use the switch to the left of the port to set the port to DTE (left) or DCE (right). Default settings for this port are 9600 bps, 8 data bits, no parity, and one stop bit.

Because the Console port expects to receive Data Set Ready (DSR) and Clear To Send (CTS) signals before transmitting, these control lines are required in the cabling. The Console port does not support any inbound flow control; that is, the port does not toggle control lines to indicate an input buffer full condition.

A-4

204515-C

Image 66

Nortel Networks 8100, 1000BASE-XD manual Management Port, Console Serial Port, Connector Pin Number Signal

Contents

Using the Passport 8100 Modules EN 55 022 Statement EC Declaration of Conformity Voluntary Control Council for Interference Vcci Statement Bureau of Standards, Metrology and Inspection Bsmi Statement 204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Preface Before You Begin Text Conventions Italic text Related Publications Xviii How to Get Help Technical Solutions Center Telephone NumberPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Switch Management Module Passport 8190SM Management Module Ethernet Management Port Serial Ports DTE/DCE SwitchReset Button Pcmcia Card Slot LEDs LEDs on the Passport 8190SM Module 10BASE-T/100BASE-TX Port Connectors Passport 8132TX 32-Port I/O Module MDA Slot Comm Port LEDs on the Passport 8132TX Module Passport 8148TX Edge Switch Module Passport 8148TX 48-Port I/O Module Passport 8108GBIC 8-Port I/O Module LEDs on the Passport 8148TX Module Redundancy Features Passport 8108GBIC Module Redundant Power Supplies Redundant Passport 8190SM Modules Power Supply Hot-Swapping Chassis Number Hot-Swap One? Modules Power Supplies Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Chassis Configuration Requirements Safety and Environmental Precautions Installing a Module Removing a Filler Panel Slide the module into the slot Figure Turning On the Chassis Power Securing the Module in the Chassis Connecting Cables Replacing Modules Routing Network Cables To replace a module Chapter Basic Switch Configuration Specifying Port Numbers Port Numbers on High-Density Modules Booting the Switch Access Levels and Default Login Values Access Level Description Default Login PasswordLogging On to the System Setting System Identification Assigning an IP Address to the Management Port Setting System Security Change CLI users and passwords using the following commands Change Web passwords using the command Switch Configuration To assign an IP address for management, use the command Specify a default gateway address/default route Page Chapter Troubleshooting Normal Power-Up Sequence Failure to Get a Login Prompt from the Console Port LED Indications of ProblemsFailure of Management Software to Recognize I/O Modules LED Indications of Problems Symptom Probable Cause Corrective Action Port Connection Problems Cabling Autonegotiation Modes Use the CLI to disable autonegotiation for the suspect port Port Interface Installation-Related Issues AddressesPage Appendix a Technical Specifications General SpecificationsStandards Supported Safety Agency Approvals Environmental SpecificationsPerformance Specifications 64-byte packets Data Rate and Encoding Passport 8190SM Switch Management Module Connector Pin Number Signal Management PortConsole Serial Port Modem Serial Port Table A-3 DTE-to-DCE Pin Assignments Cable Specifications Data Port ConnectorsConnector Type Passport 8132TX Module 450-1SR MDA, 450-1SX MDA Comm Port ConnectorMDAs 450-1LR MDA, 450-1LX MDA Port Connectors Passport 8148TX ModuleTable A-5. Passport 8148TX Port Pinouts Passport 8108GBIC Module GBICs Optical Specifications 1000BASE-SX Gbic 1000BASE-XD Gbic MDI and MDI-X Connections Figure A-1. MDI-X to MDI Cable Connections Declaration of Conformity Figure A-2. MDI-X to MDI-X Cable ConnectionsPage Appendix B LEDs Figure B-1. LEDs on the Passport 8190SM Module Table B-1 LED Operation on the Passport 8190SM Module Label Color/State Meaning Passport 8132TX and 8148TX I/O Modules Figure B-2. LEDs on the Passport 8132TX and 8148TX Modules LED Color/State Meaning Table B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Series MDAs Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Table C-1 1000BASE-SX MDA LEDs Label Type Color/State Meaning 8100-4TX MDA Table C-2 1000BASE-LX MDA LEDs Series Fiber MDAs Table C-3 8100-4TX MDA LEDs Figure C-4 Series MDA Front Panels Table C-4 Series MDA LEDs Installing an MDA Figure C-5. Installing an MDA Using the Passport 8100 Modules Appendix D Installing GBICs Figure D-1. Types of GBICs Installing a Gbic Figure D-2. Installing a Gbic To remove an installed Gbic Page Appendix E RFCs and Standards Page Index Numbers Index-2 Index-3 Index-4