Manuals / Nortel Networks / Computer Equipment / Switch

Nortel Networks Using the Passport 8100 Modules, Figure C-4. 8100 Series MDA Front Panels

Models: 1000BASE-XD 8100

1 100

Download 100 pages 29.82 Kb

Page 88

Figure C-4. 8100 Series MDA Front Panels

Using the Passport 8100 Modules

8100-2FX MDA (2-port SC connectors)

100BASE-FX		100BASE-FX
				Link
				F Dx
				Activity
TX	RX	TX	RX	8100-2FX MDA
				8100-2FX MDA

8100-4FX MDA

(4-port MT-RJ connectors)

Link

F Dx

Activity

8100-4FX MDA

2

1

2

1

9214EB

1 = LEDs

2 = 100BASE-FX SC Port Connectors

Figure C-4. 8100 Series MDA Front Panels

Table C-4 describes the 8100 Series MDA LEDs.

Table C-4.		8100 Series MDA LEDs

Label	Type		Color/State	Meaning

Link	Communication		Green/On	A valid communication link is established.
	Link LEDs		Green/	The corresponding port is management disabled.
			Green/	The corresponding port is management disabled.
			Blinking
			Off	The communication link connection is bad, or there is no
				connection to this port.

F Dx	Full-duplex port		Green/On	The corresponding port is in full-duplex mode.
	status LEDs		Green/Off	The corresponding port is in half-duplex mode.
			Green/Off	The corresponding port is in half-duplex mode.

Activity	Port activity		Green/	Indicates the network activity level for the corresponding port.
	LEDs		Blinking	A high level of network activity can cause LEDs to appear to be on
				continuously.

C-6

204515-C

Image 88

Nortel Networks Using the Passport 8100 Modules, Figure C-4. 8100 Series MDA Front Panels, Table C-4, Series MDA LEDs

Contents

Using the Passport 8100 Modules Part No. 204515-C April 4401 Great America Parkway Santa Clara, CACopyright 2000 Nortel Networks TrademarksStatement of Conditions USA Requirements OnlyJapan/Nippon Requirements Only Taiwan RequirementsCanada Requirements Only Nortel Networks NA Inc. Software License Agreement2. Restrictions on use reservation of rights. The Software and user manuals are protected under copyright laws. Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including any revisions made by Nortel Networks or its licensors. The copyright notice must be reproduced and included with any copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble, use for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user manuals or any copy, in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or transfer the Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’ and its licensors’ confidential and proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise disclose to any third party the Software, or any information about the operation, design, performance, or implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors however, Licensee may grant permission to its consultants, subcontractors, and agents to use the Software at Licensee’s facility, provided they have agreed to use the Software only in accordance with the terms of this license Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such intended examination of the Software and may procure support and assistance from Nortel Networks 204515-C Contents PrefaceChapter About the Passport 8100 ModulesChapter Installing a Passport 8100 Module Basic Switch ConfigurationTroubleshooting ChapterAppendix B Appendix A Technical SpecificationsLEDs Installing GBICs Appendix C Media Dependent AdaptersAppendix D Appendix E RFCs and Standards IndexFigures Figure C-1. 1000BASE-SX Shortwave Gigabit MDA Front Panels Tables 204515-C Preface Before You BeginText Conventions italic textRelated Publications arguments. Enter only one of the choices. Do not type theInstalling the Passport 8001PS AC Power Supply part number 204519-B Technical Solutions Center How to Get HelpTelephone Number Page Chapter About the Passport 8100 Modules Features IEEE 802.1Q port-based virtual LANs VLANs IEEE 802.1p prioritization Passport 8190SM Management Module Ethernet Management Port DTE/DCE Switch Reset ButtonSerial Ports PCMCIA Card SlotLEDs Figure 1-2. LEDs on the Passport 8190SM Module10BASE-T/100BASE-TX Port Connectors Passport 8132TX 32-Port I/O ModuleMDA Slot Comm PortFigure 1-4. LEDs on the Passport 8132TX Module LEDs1 = Module LEDs 2 = Port Speed LEDs 3 = Port Link/Activity LEDs Passport 8148TX 48-Port I/O Module Figure 1-5. Passport 8148TX Edge Switch ModulePassport 8108GBIC 8-Port I/O Module LEDsRedundancy Features LEDsFigure 1-7. Passport 8108GBIC Module Figure 1-8. LEDs on the Passport 8108GB ModuleRedundant Power Supplies Redundant Passport 8190SM ModulesFailure of the power supply module Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Chassis Configuration Requirements Safety and Environmental PrecautionsInstalling a Module To install a module in a Passport 8000 Series chassisUsing the Passport 8100 Modules Figure 2-4. Seating the Backplane ConnectorsFigure 2-3. Inserting a Module 204515-CTurning On the Chassis Power Connecting Cables Using the Passport 8100 ModulesConnector ModuleReplacing Modules Figure 2-6. Routing Network Cables1. Disconnect all network cables from the module to be removed Chapter Basic Switch Configuration Specifying Port Numbers Booting the Switch Basic Switch ConfigurationLogging On to the System Access Levels and Default Login ValuesSetting System Identification Assigning an IP Address to the Management PortUse the following command 1. Specify the system name using the commandSetting System Security 1. Change CLI users and passwords using the following commands2. Change SNMP community strings using the command 3. Enable or disable Web access using the commands4. Change Web passwords using the command 2. Enable or disable Telnet access using the command1. Confirm that all ports are in the default VLAN using the command Switch Configuration2. To assign an IP address for management, use the command 3. Specify a default gateway address/default route 4. To save the configuration, enterPage Chapter Troubleshooting Normal Power-Up SequenceFailure to Get a Login Prompt from the Console Port LED Indications of ProblemsFailure of Management Software to Recognize I/O Modules Figure 4-1. DCE/DTE Switch on the Passport 8190SM ModuleTroubleshooting Table 4-1. LED Indications of ProblemsSymptom Probable CausePort Connection Problems CablingAutonegotiation Modes Port Interface Installation-Related Issues AddressesPage Appendix A Technical Specifications General SpecificationsUsing the Passport 8100 Modules Environmental SpecificationsPerformance Specifications 64-byte packets Safety Agency ApprovalsPassport 8190SM Switch Management Module Technical SpecificationsPhysical Specifications Electrical SpecificationsConsole Serial Port Management PortTable A-1. Pin Assignments in the Passport 8190SM Management Port Modem Serial Port Table A-2. Pin Assignments in the Passport 8190SM Console PortTable A-3 DTE-to-DCE Pin AssignmentsData Port Connectors Passport 8132TX ModuleUsing the Passport 8100 Modules Physical SpecificationsComm Port Connector MDAs450-1SR MDA, 450-1SX MDA 450-1LR MDA, 450-1LX MDAPort Connectors Passport 8148TX ModuleUsing the Passport 8100 Modules Physical SpecificationsPassport 8108GBIC Module GBICsTechnical Specifications Physical Specifications1000BASE-SX GBIC 1000BASE-LX GBICUsing the Passport 8100 Modules Cable Specifications1000BASE-XD GBIC 1000BASE-ZX GBICTechnical Specifications Cable SpecificationsMDI and MDI-X Connections Figure A-1. MDI-X to MDI Cable ConnectionsDeclaration of Conformity Figure A-2. MDI-X to MDI-X Cable ConnectionsPage Appendix B LEDs Passport 8190SM Switch Management ModulePassport 8190SM Switch Management Module this page Passport 8132TX and 8148TX I/O Modules page B-3Using the Passport 8100 Modules Table B-1LED Operation on the Passport 8190SM Module LabelPassport 8132TX and 8148TX I/O Modules Figure B-2. LEDs on the Passport 8132TX and 8148TX ModulesPassport 8108GBIC Module Table B-2. Module LEDs on the Passport 8132TX and 8148TX ModulesTable B-3 Port LEDs on the Passport 8132TX and 8148TX ModulesLEDs Figure B-3. LEDs on the Passport 8108GBIC ModuleTable B-4 Module LEDs on the Passport 8108GBIC ModulePage Appendix C Media Dependent Adapters 450 Series MDAs Media Dependent Adapters Figure C-2. 1000BASE-LX Longwave Gigabit MDA Front PanelsTable C-1 1000BASE-SX MDA LEDs8100-4TX MDA Using the Passport 8100 ModulesTable C-2 1000BASE-LX MDA LEDs8100 Series Fiber MDAs Using the Passport 8100 Modules Figure C-4. 8100 Series MDA Front PanelsTable C-4 8100 Series MDA LEDsInstalling an MDA 8. Tighten the module retaining screws Appendix D Installing GBICs Installing a GBIC 1. Remove the GBIC from its protective packaging2. Insert the GBIC into the slot on the module Figure D-2 3. Press on the front of the GBIC until it snaps into placeTo remove an installed GBIC Figure D-3. Removing a GBICPage Appendix E RFCs and Standards Page Numbers IndexIndex-1 Index-2 Index-3 Index-4