Passport 8132TX 32-Port I/O Module | Nortel Networks 8100 specs

Using the Passport 8100 Modules

Passport 8132TX 32-Port I/O Module

The Passport 8132TX module (Figure 1-3) is a single-slot I/O module for the Passport 8000 Series chassis. It has 32 autosensing 10BASE-T/100BASE-TX switched ports with RJ-45 connectors. The ports have integrated LEDs to indicate port operation, and the module has three additional LEDs to indicate system operation. An expansion slot allows you to install an MDA to provide additional port types. You can add 10/100BASE-T, 100BASE-FX, or Gigabit Ethernet ports by installing an optional MDA in the Passport 8132TX module. Inserter/extractor levers and captive retaining screws are at each end of the module.

9155EA

Figure 1-3. Passport 8132TX Edge Switch Module

10BASE-T/100BASE-TX Port Connectors

The Passport 8132TX module provides 32 10/100 Mb/s autosensing ports that support the IEEE 802.3u autonegotiation standard. Each port can operate in full- or half-duplex mode. When a port is connected to another device that also supports the IEEE 802.3u standard, the two devices negotiate the best speed and duplex mode of operation.

The port connectors are 8-pin modular RJ-45 connectors configured as MDI-X (media-dependent interface-crossover) connections. You can connect these ports to an MDI port (for example, a workstation or server) using a straight-through cable. If you are connecting to a device that does not have an MDI port, use a crossover cable (see “MDI and MDI-X Connections” on page A-12).

Note: For 10 Mb/s connections, you can use Category 3, 4, or 5 copper unshielded twisted pair (UTP) cable. Use only Category 5 UTP cable to connect ports that will operate at 100 Mb/s.

Refer to Appendix A, “Technical Specifications,” for more information about the RJ-45 port connectors.

1-8

204515-C

Image 28

Nortel Networks 8100, 1000BASE-XD manual Passport 8132TX 32-Port I/O Module, 10BASE-T/100BASE-TX Port Connectors

Contents

Using the Passport 8100 Modules EN 55 022 Statement EC Declaration of Conformity Voluntary Control Council for Interference Vcci Statement Bureau of Standards, Metrology and Inspection Bsmi Statement 204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Preface Before You Begin Text Conventions Italic text Related Publications Xviii How to Get Help Technical Solutions Center Telephone NumberPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Switch Management Module Passport 8190SM Management Module Ethernet Management Port DTE/DCE Switch Reset ButtonSerial Ports Pcmcia Card Slot LEDs LEDs on the Passport 8190SM Module 10BASE-T/100BASE-TX Port Connectors Passport 8132TX 32-Port I/O Module MDA Slot Comm Port LEDs on the Passport 8132TX Module Passport 8148TX Edge Switch Module Passport 8148TX 48-Port I/O Module Passport 8108GBIC 8-Port I/O Module LEDs on the Passport 8148TX Module Redundancy Features Passport 8108GBIC Module Redundant Power Supplies Redundant Passport 8190SM Modules Power Supply Hot-Swapping Chassis Number Hot-Swap One? Modules Power Supplies Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Chassis Configuration Requirements Safety and Environmental Precautions Installing a Module Removing a Filler Panel Slide the module into the slot Figure Turning On the Chassis Power Securing the Module in the Chassis Connecting Cables Replacing Modules Routing Network Cables To replace a module Chapter Basic Switch Configuration Specifying Port Numbers Port Numbers on High-Density Modules Booting the Switch Access Level Description Default Login Password Access Levels and Default Login ValuesLogging On to the System Setting System Identification Assigning an IP Address to the Management Port Setting System Security Change CLI users and passwords using the following commands Change Web passwords using the command Switch Configuration To assign an IP address for management, use the command Specify a default gateway address/default route Page Chapter Troubleshooting Normal Power-Up Sequence LED Indications of Problems Failure to Get a Login Prompt from the Console PortFailure of Management Software to Recognize I/O Modules LED Indications of Problems Symptom Probable Cause Corrective Action Port Connection Problems Cabling Autonegotiation Modes Use the CLI to disable autonegotiation for the suspect port Port Interface Installation-Related Issues AddressesPage General Specifications Appendix a Technical SpecificationsStandards Supported Environmental Specifications Performance Specifications 64-byte packetsSafety Agency Approvals Data Rate and Encoding Passport 8190SM Switch Management Module Management Port Connector Pin Number SignalConsole Serial Port Modem Serial Port Table A-3 DTE-to-DCE Pin Assignments Data Port Connectors Connector TypeCable Specifications Passport 8132TX Module Comm Port Connector MDAs450-1SR MDA, 450-1SX MDA 450-1LR MDA, 450-1LX MDA Passport 8148TX Module Port ConnectorsTable A-5. Passport 8148TX Port Pinouts Passport 8108GBIC Module GBICs Optical Specifications 1000BASE-SX Gbic 1000BASE-XD Gbic MDI and MDI-X Connections Figure A-1. MDI-X to MDI Cable Connections Declaration of Conformity Figure A-2. MDI-X to MDI-X Cable ConnectionsPage Appendix B LEDs Figure B-1. LEDs on the Passport 8190SM Module Table B-1 LED Operation on the Passport 8190SM Module Label Color/State Meaning Passport 8132TX and 8148TX I/O Modules Figure B-2. LEDs on the Passport 8132TX and 8148TX Modules LED Color/State Meaning Table B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Series MDAs Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Table C-1 1000BASE-SX MDA LEDs Label Type Color/State Meaning 8100-4TX MDA Table C-2 1000BASE-LX MDA LEDs Series Fiber MDAs Table C-3 8100-4TX MDA LEDs Figure C-4 Series MDA Front Panels Table C-4 Series MDA LEDs Installing an MDA Figure C-5. Installing an MDA Using the Passport 8100 Modules Appendix D Installing GBICs Figure D-1. Types of GBICs Installing a Gbic Figure D-2. Installing a Gbic To remove an installed Gbic Page Appendix E RFCs and Standards Page Index Numbers Index-2 Index-3 Index-4