Chapter Basic Switch Configuration | Nortel Networks 1000BASE-XD

Chapter 3

Basic Switch Configuration

This chapter describes how to use the command line interface (CLI) for basic switch configuration. The chapter includes the following information:

•Port numbering (page 3-2)

•Booting the switch (page 3-3)

•Logging on to the system (page 3-4)

•Assigning an IP address to the Management port (page 3-5)

•Setting system identification (page 3-5)

•Setting system security (page 3-6)

•Sample configuration (page 3-8)

For information about more advanced configuration topics, refer to the following publications:

•Networking Concepts for the Passport 8000 Series Switch

•Reference for the Passport 8000 Series Management Software Switching Operations

•Reference for the Passport 8000 Series Command Line Interface Switching Operations

Note: To perform configuration procedures, you must log on to the switch with Read-Write privileges.

204515-C

3-1

Image 45

Nortel Networks 1000BASE-XD, 8100 manual Chapter Basic Switch Configuration

Contents

Using the Passport 8100 Modules EC Declaration of Conformity EN 55 022 Statement Bureau of Standards, Metrology and Inspection Bsmi Statement Voluntary Control Council for Interference Vcci Statement 204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Before You Begin Preface Italic text Text Conventions Related Publications Xviii Technical Solutions Center Telephone Number How to Get HelpPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Management Module Passport 8190SM Switch Management Module Ethernet Management Port Reset Button DTE/DCE SwitchSerial Ports Pcmcia Card Slot LEDs on the Passport 8190SM Module LEDs Passport 8132TX 32-Port I/O Module 10BASE-T/100BASE-TX Port Connectors Comm Port MDA Slot LEDs on the Passport 8132TX Module Passport 8148TX 48-Port I/O Module Passport 8148TX Edge Switch Module LEDs on the Passport 8148TX Module Passport 8108GBIC 8-Port I/O Module Passport 8108GBIC Module Redundancy Features Redundant Passport 8190SM Modules Redundant Power Supplies Chassis Number Hot-Swap One? Modules Power Supplies Power Supply Hot-Swapping Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Safety and Environmental Precautions Chassis Configuration Requirements Removing a Filler Panel Installing a Module Slide the module into the slot Figure Securing the Module in the Chassis Turning On the Chassis Power Connecting Cables Routing Network Cables Replacing Modules To replace a module Chapter Basic Switch Configuration Port Numbers on High-Density Modules Specifying Port Numbers Booting the Switch Access Levels and Default Login Values Access Level Description Default Login PasswordLogging On to the System Assigning an IP Address to the Management Port Setting System Identification Change CLI users and passwords using the following commands Setting System Security Change Web passwords using the command To assign an IP address for management, use the command Switch Configuration Specify a default gateway address/default route Page Normal Power-Up Sequence Chapter Troubleshooting Failure to Get a Login Prompt from the Console Port LED Indications of ProblemsFailure of Management Software to Recognize I/O Modules Symptom Probable Cause Corrective Action LED Indications of Problems Cabling Port Connection Problems Autonegotiation Modes Port Interface Use the CLI to disable autonegotiation for the suspect port Addresses Installation-Related IssuesPage Appendix a Technical Specifications General SpecificationsStandards Supported Performance Specifications 64-byte packets Environmental SpecificationsSafety Agency Approvals Data Rate and Encoding Passport 8190SM Switch Management Module Connector Pin Number Signal Management PortConsole Serial Port Table A-3 DTE-to-DCE Pin Assignments Modem Serial Port Connector Type Data Port ConnectorsCable Specifications Passport 8132TX Module MDAs Comm Port Connector450-1SR MDA, 450-1SX MDA 450-1LR MDA, 450-1LX MDA Port Connectors Passport 8148TX ModuleTable A-5. Passport 8148TX Port Pinouts GBICs Passport 8108GBIC Module 1000BASE-SX Gbic Optical Specifications 1000BASE-XD Gbic Figure A-1. MDI-X to MDI Cable Connections MDI and MDI-X Connections Figure A-2. MDI-X to MDI-X Cable Connections Declaration of ConformityPage Figure B-1. LEDs on the Passport 8190SM Module Appendix B LEDs Label Color/State Meaning Table B-1 LED Operation on the Passport 8190SM Module Figure B-2. LEDs on the Passport 8132TX and 8148TX Modules Passport 8132TX and 8148TX I/O Modules Color/State Meaning LED Table B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Series MDAs Label Type Color/State Meaning Table C-1 1000BASE-SX MDA LEDs Table C-2 1000BASE-LX MDA LEDs 8100-4TX MDA Table C-3 8100-4TX MDA LEDs Series Fiber MDAs Table C-4 Series MDA LEDs Figure C-4 Series MDA Front Panels Figure C-5. Installing an MDA Installing an MDA Using the Passport 8100 Modules Figure D-1. Types of GBICs Appendix D Installing GBICs Figure D-2. Installing a Gbic Installing a Gbic To remove an installed Gbic Page Appendix E RFCs and Standards Page Numbers Index Index-2 Index-3 Index-4