Turning On the Chassis Power | Nortel Networks 1000BASE-XD, 8100

Installing a Passport 8100 Module

5.Tighten the retaining screws to secure the module in the chassis (Figure 2-5).

9400FA

Figure 2-5. Securing the Module in the Chassis

Turning On the Chassis Power

Although you can install or replace modules in an operating chassis, in a new installation you may prefer to install all the modules before turning on the chassis power.

To turn on the chassis power:

1.Verify that all power cords are connected properly, as described in the installation instructions for the power supplies.

2.Turn all the power switches to the On position.

Note: In a chassis with two power supplies in a nonredundant power configuration, you must turn on both power supply units within 2 seconds of each other. If you wait longer to turn on the second power supply, both power supplies will shut down. To correct this condition, turn off both power supplies, wait at least 30 seconds, and then turn on both power supplies again within 2 seconds.

204515-C

2-5

Image 41

Nortel Networks 1000BASE-XD, 8100 manual Turning On the Chassis Power, Securing the Module in the Chassis

Contents

Using the Passport 8100 Modules EC Declaration of Conformity EN 55 022 Statement Bureau of Standards, Metrology and Inspection Bsmi Statement Voluntary Control Council for Interference Vcci Statement 204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Before You Begin Preface Italic text Text Conventions Related Publications Xviii Technical Solutions Center Telephone Number How to Get HelpPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Management Module Passport 8190SM Switch Management Module Ethernet Management Port Reset Button DTE/DCE SwitchSerial Ports Pcmcia Card Slot LEDs on the Passport 8190SM Module LEDs Passport 8132TX 32-Port I/O Module 10BASE-T/100BASE-TX Port Connectors Comm Port MDA Slot LEDs on the Passport 8132TX Module Passport 8148TX 48-Port I/O Module Passport 8148TX Edge Switch Module LEDs on the Passport 8148TX Module Passport 8108GBIC 8-Port I/O Module Passport 8108GBIC Module Redundancy Features Redundant Passport 8190SM Modules Redundant Power Supplies Chassis Number Hot-Swap One? Modules Power Supplies Power Supply Hot-Swapping Combining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Safety and Environmental Precautions Chassis Configuration Requirements Removing a Filler Panel Installing a Module Slide the module into the slot Figure Securing the Module in the Chassis Turning On the Chassis Power Connecting Cables Routing Network Cables Replacing Modules To replace a module Chapter Basic Switch Configuration Port Numbers on High-Density Modules Specifying Port Numbers Booting the Switch Logging On to the System Access Levels and Default Login ValuesAccess Level Description Default Login Password Assigning an IP Address to the Management Port Setting System Identification Change CLI users and passwords using the following commands Setting System Security Change Web passwords using the command To assign an IP address for management, use the command Switch Configuration Specify a default gateway address/default route Page Normal Power-Up Sequence Chapter Troubleshooting Failure of Management Software to Recognize I/O Modules Failure to Get a Login Prompt from the Console PortLED Indications of Problems Symptom Probable Cause Corrective Action LED Indications of Problems Cabling Port Connection Problems Autonegotiation Modes Port Interface Use the CLI to disable autonegotiation for the suspect port Addresses Installation-Related IssuesPage Standards Supported Appendix a Technical SpecificationsGeneral Specifications Performance Specifications 64-byte packets Environmental SpecificationsSafety Agency Approvals Data Rate and Encoding Passport 8190SM Switch Management Module Console Serial Port Connector Pin Number SignalManagement Port Table A-3 DTE-to-DCE Pin Assignments Modem Serial Port Connector Type Data Port ConnectorsCable Specifications Passport 8132TX Module MDAs Comm Port Connector450-1SR MDA, 450-1SX MDA 450-1LR MDA, 450-1LX MDA Table A-5. Passport 8148TX Port Pinouts Port ConnectorsPassport 8148TX Module GBICs Passport 8108GBIC Module 1000BASE-SX Gbic Optical Specifications 1000BASE-XD Gbic Figure A-1. MDI-X to MDI Cable Connections MDI and MDI-X Connections Figure A-2. MDI-X to MDI-X Cable Connections Declaration of ConformityPage Figure B-1. LEDs on the Passport 8190SM Module Appendix B LEDs Label Color/State Meaning Table B-1 LED Operation on the Passport 8190SM Module Figure B-2. LEDs on the Passport 8132TX and 8148TX Modules Passport 8132TX and 8148TX I/O Modules Color/State Meaning LED Table B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Series MDAs Label Type Color/State Meaning Table C-1 1000BASE-SX MDA LEDs Table C-2 1000BASE-LX MDA LEDs 8100-4TX MDA Table C-3 8100-4TX MDA LEDs Series Fiber MDAs Table C-4 Series MDA LEDs Figure C-4 Series MDA Front Panels Figure C-5. Installing an MDA Installing an MDA Using the Passport 8100 Modules Figure D-1. Types of GBICs Appendix D Installing GBICs Figure D-2. Installing a Gbic Installing a Gbic To remove an installed Gbic Page Appendix E RFCs and Standards Page Numbers Index Index-2 Index-3 Index-4