Power on and OFF, Power OFF | Olivetti 2701, 2301 manual

POWER ON AND OFF

The power switch is located on the left side of the machine.

Note When the power switch is turned on, the machine starts up in the previously used mode. The following explanations assume that the previously used mode was copy mode.

POWER ON

Turn the power switch to the "ON" position.

ON

•When the power switch is turned to the "ON" position, the message "WARMING UP. A COPYING JOB CAN BE SET NOW." will appear in the message display and the machine will start warming up. When "READY TO COPY." appears, the machine is ready to copy. Copy settings can be selected during warm-up.

•If auditing mode is enabled, "ENTER YOUR ACCOUNT NUMBER." will appear. When a valid account number is entered, the account status will appear on the main screen for several seconds. Then copying can be performed. (See "Key operator's guide".)

POWER OFF

When the machine is not used for a long time, be sure to turn it off.

Make sure that the machine is not in operation 1 and then turn the power switch to the "OFF" position.

OFF

If the power switch is turned off while the machine is in operation, a misfeed may occur and the job that was in progress will be cancelled.

Note	If the fax option is installed, be sure to keep the power turned on. Faxes cannot be received when the power is
	turned off.

13

Image 15

Olivetti 2701, 2301 operation manual Power on and OFF, Power OFF, Turn the power switch to the on position

Contents

Copia 2301 d-Copia Publication Issued by Contents 500-SHEET Paper Feed Unit When a finisher AR-FN5N is installed Air conditioner or Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Changes, e.g., near an Do not touch the photoconductive drum green portion Trademark acknowledgements Environmental Information Using the ManualSoftware setup guide for printer Key operators guide/software setup guide Pass Feeder as the Rspf Meaning of R in Original and Paper Size IndicationsConventions Used in this Manual Explanation of words and illustration Main Features Part Names and Functions Interior Operation Panel Using the touch panel Selecting a function Touch PanelExample Print JOB key Mode switching keysDisplay switching keys Job list Turn the power switch to the on position Power on and OFFPower on Power OFF Auto power shut-off mode Initial SettingsPower Save Modes Preheat mode Tray Paper tray type Paper type Size Weight Capacity Loading PaperUpper paper tray*1 Plain paper A5 to A3 56 g/m2 to 105 g/m2 Letterhead paper Follow these guidelines when using special papersSpecial papers Envelopes Loading the paper in the paper tray Loading Paper Important points when inserting paper in the bypass tray Loading paper in the bypass traySet the paper guides to the copy paper width Changing a TRAY’S Paper Type and Paper Size Settings Touch the Tray Settings keySelect the tray in which you loaded paper Setting the paper type in the bypass tray Main Screen of Copy Mode Close the document cover/RSPF How to place the originalNormal Copying Copying from the Document Glass Copying a large number of originals Adjust the original guides to the size of the originalStream feeding mode Copying from the Rspf Removing the document cover Points to Note When Making CopiesDocument glass and Rspf Originals that can be used in the Rspf Touch the Special Modes key Select the MIX Size Original Feeding Mode checkboxCopying originals of mixed length Mixed feeding Automatic copy image rotation rotation copying Tray. p.20 Shifting the starting position of copyingSet the type of paper that You loaded in the bypass Original → Paper Using the Document GlassAutomatic TWO-SIDED Copying Touch the One-sided to two-sided copy key Original for the front side is scanned Using the RspfTouch the desired copy mode To cancel automatic two-sided copying, press the Clear key Exposure value guidelines Exposure AdjustmentTouch the Exposure key Manually adjust the copy exposure Selecting the original image type Place the originals. p.22, p.23 Original type setting Original position Selectable ratiosREDUCTION/ENLARGEMENT/ZOOM Automatic Ratio Selection Place the originals. p.22, p.23 Touch the Copy Ratio key Manual Ratio Selection Touch the XY Zoom key Direction Copy ratio in the vertical Y directionZoom keys To change Copy ratio in the horizontal Interrupting a Copy RUN Press the Interrupt key to interrupt the copy runReplace only the originals that have not yet been scanned Offset Function Copy Finishing FunctionsSort Copy Group Copy Touch the Sort or Group key When using the RspfWhen using the document glass Touch the Output key Insert the originals face up Place each original face down Using the Rspf Using the document glassStaple Sort Orientation of the Original and Stapling Positions Place the originals. p.22, p.23 Touch the Output key Touch the Staple Sort keyCopying will start after all originals have been scanned Special Modes General Procedure for Using the Special Functions Touch the key of the desired special modeExample Selecting the margin shift function Select the shift direction Adjust the shift width as needed and touch the OK keyMargin Shift Copy Touch the Margin Shift key in the special modes screen Touch the Erase key in the special modes screen Select the desired erase modeAdjust the erase width as needed and touch the OK key Erase Copy Place the originals on the document glass. p.22 When copying book originalsDual page Copy Touch the Dual page Copy key in the special modes screen Function is enabled Pamphlet CopySpecify whether 1-sided or 2-sided originals will be copied JOB Build Mode Touch the JOB Build key in the special modes menu screenTouch the READ-END key Multi Shot Copy Touch the inside OK key Original SizeTouch the Manual key Select the original size Cover Copy Copying onto a coverNot copying onto a cover Specify whether or not the front cover is to be copied on Touch the OK key in the cover setting screenSelect the covers that you wish to add Load the cover paper to be used into the bypass tray Reverse Copy Touch the outer OK key 50a Back side of the card is scanned and copying begins 50bPlace the original on the document glass Front side of the card is scanned Programmed Custom SettingsThis is used to print a setting list or a font list. p.53 Continuous printing. p.53 Custom Settings General Procedure for Custom Settings Settings Touch the STORE/DELETE key JOB Program MemoryStoring a JOB Program Press the key Touch the STORE/DELETE key Touch the Delete key Executing a JOB ProgramDeleting a Stored JOB Program Touch the program number key of the desired program Enter your account number 5 digits with the numeric keys Auditing ModeCopying When Auditing Mode is Enabled When the copy job is finished, press the ACC.#-C key Trouble Problems related to machine operation Paper feeding problemsImage quality problems Display Messages Message Cause and solution Staples are jammed in the finisher or the staple case is not Contact your authorised service representative Problems related to machine operation Troubleshooting Originals were being scanned Automatically, or copying does notOriginal is not a standard size Copy, print job, or received fax is being printed Paper feeding problems Image quality problems Misfeed Removal Misfeed Removal GuidanceFirst, locate the misfeed Section a Misfeed in the RspfRemove the misfed original Section C Misfed paper. Doing so may cause a Misfeed in the Bypass TrayMisfeed in the Machine Misfeed in the paper feed area Make sure that the misfeed message is cleared Misfeed in the fusing areaClose the front cover and side cover Turn the roller rotating knob in the direction of the arrow Misfeed in the Centre Tray Misfeed in the Upper Paper TrayReplace the upper paper tray Close the lower side cover Misfeed in the Lower Paper TrayOpen the lower side cover Remove the misfed paper Replace the lower paper tray Misfeed in the Upper Exit Area Misfeed in AN Output TrayGently pull the misfed paper out Troubleshooting and Maintenance Close the front cover Replacing the Toner Cartridge Staple Cartridge Replacement Checking the Toner Quantity and Total Output Count Staple JAM RemovalChecking the total output count and toner quantity Surface of document glass Underside of document cover/RSPF Cleaning the MachineDocument Glass and Document COVER/RSPF Bypass Tray Paper Feed Roller Peripheral Devices and Supplies Peripheral Devices Specifications Finisher AR-FN5NPart names Sheet Paper Feed Unit Paper Upper trayCapacity Lower tray Store the supplies in a location that is Storage of SuppliesReversing Single Pass Feeder Proper Storage Saddle Stitch Finisher Parts of the Saddle Stitch Finisher79a 79b Specifications 79c Functions of the Saddle Stitch Finisher 79d Punch function only when a punch unit is installed Using the Saddle Stitch Finisher Functions Using the saddle stitch finisher functions in copy mode79e Using the saddle stitch finisher functions in printer mode 79fPCL printer driver on the Windows XP as an example Place the original p.6 Touch the Output key Select the staple position Using the RspfUsing the document glass 79g Push in the staple box 79hReplacing the staple cartridge Pull the stapler section forward Open the saddle stitch section cover Remove the staple box 79iRemoving a staple jam Remove the paper from the stapler compiler Push the staple box all the way in until you hear a click Discarding punch waste when a punch unit is installed79l Raise the lever on the front edge of the staple box Close the center cover Removing Paper Misfeeds79m Misfeed in the relay path Gently, taking care not to 79nMisfeed in the saddle stitch finisher Remove the paper Remove any misfed paper from the saddle stitch tray 79o Troubleshooting Related to Saddle Stitch Finisher When an optional punch unit is installed79p 79q Using the KEY Operator Programs Specifications Developer system ResolutionPower consumption Overall dimensions Symbols Index50a Job program How to place the originalImportant points when inserting paper Important points when selecting an installation site 15, 19 Points to note when making copiesPower save modes Setting the paper type in the bypass tray Making copies Using convenient copy functionsTroubleshooting and maintenance Preparations Class Laser Product Laser Klasse For users in the USA Information