Peripheral Devices and Supplies | Olivetti 2301, 2701 manual

6	Chapter 6
	PERIPHERAL DEVICES AND SUPPLIES

Optional equipments and supplies are explained in this chapter. To purchase optional equipment and supplies contact your authorised service representative.

PERIPHERAL DEVICES

FINISHER (AR-FN5N) See page 77.

500-SHEET PAPER FEED UNIT (AR-D21) See page 78.

2x 500-SHEET PAPER FEED UNIT (AR-D22) See page 78.

DOCUMENT COVER (AR-VR6)

REVERSING SINGLE PASS FEEDER (AR-RP7) See page 79.

SADDLE STITCH FINISHER (AR-F14) See page 79a

JOB SEPARATOR TRAY KIT (AR-TR3)

This enables separation of output locations by mode (copy, printer, etc.).

PRINTER EXPANSION KIT (AR-P17)

This allows the machine to be used as a network printer.

PRINT SERVER CARD (AR-NC5J)*1

This optional expansion kit adds the network printer function (10/100 BASE-TX).

PS3 EXPANSION KIT (AR-PK1)*1

This kit offers PostScript 3 compatibility.

BARCODE FONT KIT (AR-PF1)*1

This font set adds barcode printing capability.

NETWORK SCANNER EXPANSION KIT (AR-NS2)*2

This allows the machine to be used as a network scanner.

FACSIMILE EXPANSION KIT (AR-FX7)

This allows the machine can be used as a facsimile machine.

8MB FAX MEMORY (AR-MM9)

Image memory can be expanded by installing the optional fax expansion memory.

256MB EXPANSION MEMORY BOARD (AR-SM5) 512MB EXPANSION MEMORY BOARD (AR-SM6)

Additional memory can be installed in the machine. There are two DIMM slots in this machine, and the memory can be expanded to a maximum of 1056 MB.

*1Requires installation of the PRINTER EXPANSION KIT (AR-P17).

*2Requires installation of the PRINTER EXPANSION KIT (AR-P17), and 128MB or more of memory must be extended.

• A commercial 64/128/256/512MB (the 168 pin SDRAM DIMM) memory module can be used to expand

Note memory in this unit. For more information, consult your authorised service representative.

• Some options may not be available in some countries and regions.

76

Image 80

Olivetti 2301, 2701 operation manual Peripheral Devices and Supplies

Contents

Copia 2301 d-Copia Publication Issued by Contents When a finisher AR-FN5N is installed 500-SHEET Paper Feed Unit Important Points When Selecting AN Installation Site Do not install your machine in areas that areChanges, e.g., near an Air conditioner or Trademark acknowledgements Do not touch the photoconductive drum green portion Using the Manual Software setup guide for printerKey operators guide/software setup guide Environmental Information Meaning of R in Original and Paper Size Indications Conventions Used in this ManualExplanation of words and illustration Pass Feeder as the Rspf Main Features Part Names and Functions Interior Operation Panel Example Using the touch panel Selecting a functionTouch Panel Mode switching keys Display switching keysJob list Print JOB key Power on and OFF Power onPower OFF Turn the power switch to the on position Initial Settings Power Save ModesPreheat mode Auto power shut-off mode Upper paper tray*1 Plain paper A5 to A3 56 g/m2 to 105 g/m2 Tray Paper tray type Paper type Size Weight CapacityLoading Paper Follow these guidelines when using special papers Special papersEnvelopes Letterhead paper Loading Paper Loading the paper in the paper tray Set the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading paper in the bypass tray Select the tray in which you loaded paper Changing a TRAY’S Paper Type and Paper Size SettingsTouch the Tray Settings key Setting the paper type in the bypass tray Main Screen of Copy Mode How to place the original Normal CopyingCopying from the Document Glass Close the document cover/RSPF Adjust the original guides to the size of the original Stream feeding modeCopying from the Rspf Copying a large number of originals Points to Note When Making Copies Document glass and RspfOriginals that can be used in the Rspf Removing the document cover Select the MIX Size Original Feeding Mode checkbox Copying originals of mixed length Mixed feedingAutomatic copy image rotation rotation copying Touch the Special Modes key Shifting the starting position of copying Set the type of paper thatYou loaded in the bypass Tray. p.20 Using the Document Glass Automatic TWO-SIDED CopyingTouch the One-sided to two-sided copy key Original → Paper Using the Rspf Touch the desired copy modeTo cancel automatic two-sided copying, press the Clear key Original for the front side is scanned Exposure Adjustment Touch the Exposure key Manually adjust the copy exposureSelecting the original image type Exposure value guidelines Original type setting Original position Selectable ratios REDUCTION/ENLARGEMENT/ZOOMAutomatic Ratio Selection Place the originals. p.22, p.23 Manual Ratio Selection Place the originals. p.22, p.23 Touch the Copy Ratio key Touch the XY Zoom key Copy ratio in the vertical Y direction Zoom keys To changeCopy ratio in the horizontal Direction Replace only the originals that have not yet been scanned Interrupting a Copy RUNPress the Interrupt key to interrupt the copy run Copy Finishing Functions Sort CopyGroup Copy Offset Function When using the Rspf When using the document glassTouch the Output key Touch the Sort or Group key Using the Rspf Using the document glass Staple SortOrientation of the Original and Stapling Positions Insert the originals face up Place each original face down Copying will start after all originals have been scanned Place the originals. p.22, p.23 Touch the Output keyTouch the Staple Sort key Special Modes Example Selecting the margin shift function General Procedure for Using the Special FunctionsTouch the key of the desired special mode Adjust the shift width as needed and touch the OK key Margin Shift CopyTouch the Margin Shift key in the special modes screen Select the shift direction Select the desired erase mode Adjust the erase width as needed and touch the OK keyErase Copy Touch the Erase key in the special modes screen When copying book originals Dual page CopyTouch the Dual page Copy key in the special modes screen Place the originals on the document glass. p.22 Specify whether 1-sided or 2-sided originals will be copied Function is enabledPamphlet Copy Touch the READ-END key JOB Build ModeTouch the JOB Build key in the special modes menu screen Multi Shot Copy Original Size Touch the Manual keySelect the original size Touch the inside OK key Not copying onto a cover Cover CopyCopying onto a cover Touch the OK key in the cover setting screen Select the covers that you wish to addLoad the cover paper to be used into the bypass tray Specify whether or not the front cover is to be copied on Reverse Copy 50a Touch the outer OK key 50b Place the original on the document glassFront side of the card is scanned Back side of the card is scanned and copying begins Custom Settings This is used to print a setting list or a font list. p.53Continuous printing. p.53 Programmed General Procedure for Custom Settings Custom Settings Settings JOB Program Memory Storing a JOB ProgramPress the key Touch the STORE/DELETE key Executing a JOB Program Deleting a Stored JOB ProgramTouch the program number key of the desired program Touch the STORE/DELETE key Touch the Delete key Auditing Mode Copying When Auditing Mode is EnabledWhen the copy job is finished, press the ACC.#-C key Enter your account number 5 digits with the numeric keys Image quality problems Trouble Problems related to machine operationPaper feeding problems Message Cause and solution Display Messages Contact your authorised service representative Staples are jammed in the finisher or the staple case is not Troubleshooting Problems related to machine operation Automatically, or copying does not Original is not a standard sizeCopy, print job, or received fax is being printed Originals were being scanned Paper feeding problems Image quality problems First, locate the misfeed Misfeed RemovalMisfeed Removal Guidance Misfeed in the Rspf Remove the misfed originalSection C Section a Misfeed in the Bypass Tray Misfeed in the MachineMisfeed in the paper feed area Misfed paper. Doing so may cause a Misfeed in the fusing area Close the front cover and side coverTurn the roller rotating knob in the direction of the arrow Make sure that the misfeed message is cleared Replace the upper paper tray Misfeed in the Centre TrayMisfeed in the Upper Paper Tray Misfeed in the Lower Paper Tray Open the lower side cover Remove the misfed paperReplace the lower paper tray Close the lower side cover Gently pull the misfed paper out Misfeed in the Upper Exit AreaMisfeed in AN Output Tray Troubleshooting and Maintenance Replacing the Toner Cartridge Close the front cover Staple Cartridge Replacement Checking the total output count and toner quantity Checking the Toner Quantity and Total Output CountStaple JAM Removal Cleaning the Machine Document Glass and Document COVER/RSPFBypass Tray Paper Feed Roller Surface of document glass Underside of document cover/RSPF Peripheral Devices Peripheral Devices and Supplies Part names SpecificationsFinisher AR-FN5N Capacity Lower tray Sheet Paper Feed UnitPaper Upper tray Storage of Supplies Reversing Single Pass FeederProper Storage Store the supplies in a location that is 79a Saddle Stitch FinisherParts of the Saddle Stitch Finisher Specifications 79b Functions of the Saddle Stitch Finisher 79c Punch function only when a punch unit is installed 79d 79e Using the Saddle Stitch Finisher FunctionsUsing the saddle stitch finisher functions in copy mode PCL printer driver on the Windows XP as an example Using the saddle stitch finisher functions in printer mode79f Select the staple position Using the Rspf Using the document glass79g Place the original p.6 Touch the Output key 79h Replacing the staple cartridgePull the stapler section forward Push in the staple box 79i Removing a staple jamRemove the paper from the stapler compiler Open the saddle stitch section cover Remove the staple box Discarding punch waste when a punch unit is installed 79lRaise the lever on the front edge of the staple box Push the staple box all the way in until you hear a click Removing Paper Misfeeds 79mMisfeed in the relay path Close the center cover 79n Misfeed in the saddle stitch finisherRemove the paper Gently, taking care not to 79o Remove any misfed paper from the saddle stitch tray 79p Troubleshooting Related to Saddle Stitch FinisherWhen an optional punch unit is installed Using the KEY Operator Programs 79q Specifications Resolution Power consumptionOverall dimensions Developer system 50a SymbolsIndex How to place the original Important points when inserting paperImportant points when selecting an installation site Job program Points to note when making copies Power save modesSetting the paper type in the bypass tray 15, 19 Using convenient copy functions Troubleshooting and maintenancePreparations Making copies Class Laser Product Laser Klasse For users in the USA Information