Contents | Omega CN1166 manual

161 -DIN RAMP/SOAK PROFILE CONTROLLER

PRODUCT MANUAL

VOLUME I

INSTALLATION & CONFIGURATION

INSTRUCTIONS

The procedures described in this Volume must be undertaken only by technically-competent servicing personnel.

CONTENTS

1	INSTALLATION	1-1
1.1	UNPACKING PROCEDURE	1-1
1.2	PANEL-MOUNTING THE CONTROLLER	1-1
1.3	CONNECTIONS AND WIRING	1-2
2	INTERNAL LINKS AND SWITCHES	2-1
2.1	REMOVING THE PROFILE CONTROLLER FROM ITS HOUSING	2-1

2.2REMOVING/REPLACING THE OUTPUT 2/OUTPUT 3 OPTION PCBs 2-3

2.3REMOVING/REPLACING THE RS485 COMMUNICATIONS

	OPTION PCB OR REMOTE RUN/HOLD OPTION PCB	2-3
2.4	REPLACING THE INSTRUMENT IN ITS HOUSING	2-3
2.5	SELECTION OF INPUT TYPE AND OUTPUT 1 TYPE	2-4
2.6	OUTPUT 2 TYPE/OUTPUT 3 TYPE	2-6
3	CONFIGURATION MODE	3-1
3.1	ENTRY INTO CONFIGURATION MODE	3-1
3.2	HARDWARE DEFINITION CODE	3-1
3.3	OPTION SELECTION	3-3
3.4	CONFIGURATION MODE PARAMETERS	3-4
3.5	EXIT FROM CONFIGURATION MODE	3-9

PM077-V1

Volume I

(i)

Image 5

Omega CN1166 manual Contents

Contents

Page Page RAMP/SOAK Profile Volume Operating Instructions Volume Installation & Configuration Instructions Contents PANEL-MOUNTING the Controller Unpacking Procedure Connections and Wiring Rear Terminal Connections 2 24V Nominal AC/DC Supply Mains Line InputThermocouple Input RTD Inputs Remote Run/Hold Input Linear InputsRelay Outputs SSR Drive Outputs 11 RS485 Serial Communications Link DC Outputs Removing the Profile Controller from ITS Housing Internal Links and Switches Removing the Output 2/Output 3 Option PCBs REMOVING/REPLACING the Output 2/OUTPUT 3 Option PCBs Replacing the Instrument in ITS Housing Input Type Selection of Input Type and Output 1 Type CPU PCB Relay/SSR Drive/Solid State Output Primary Output Output 1 Type Output 2 TYPE/OUTPUT 3 Type Hardware Definition Code Entry Into Configuration Mode Wit h Hardw are Definit ion Code displayed Configurat ion Mode Hardware Definition Code Input/Output Type Selection Option Selection Wit h Hardw are Definit ion Code displayed Configuration Mode Parameters Parameter AL1 OFF, AL2 OFF Parameter Page Exit from Configuration Mode Base Mode Program Definition Mode CREATING/EDITING a Program Controller SET-UP ModeModbus Communications Alphabetic Index Display Sequence no Program Running Base Mode Putting a Program in Hold Starting a ProgramReleasing a Program from Hold Aborting a Program Read Only whilst Program is running/held Display Sequence Program Running PRE-TUNE Feature RaPID Control Feature Indication of PRE-TUNE and RaPID Status Engaging Both PRE-TUNE and RaPID Features RaPID Status when Hardware Definition Code has the following significance Viewing the Hardware Definition Code Press till front panel shows Press or to change display to Manual Control Controller SET-UP Mode Lower display = Parameter Details Parameter Function Adjustment Range Default Value ON/OFF Parameter Function Adjustment Range Default Value Power Alarm Operation Deviation When this display shows Exit from Controller SET-UP Mode Entry Program Definition Mode CREATING/EDITING a Program Basic Guidelines Creating a Program To make a Soak segment Defining Segments Rate Mode Defining Segments Time Mode Program Options T p o i n t Guaranteed Soak Band Segment Event Status Press key To display Exit from Program Define Mode Default Values and Adjustment Ranges Message Formats IntroductionModbus Functions Supported CRC16 Read Coil Status Read n Bits 01/02 Force Single Coil Write 1 Bit Read Holding Registers Read n Words 03/04 Preset Multiple Registers Write n Words 16 B Preset Single Register Write 1 Word 06 BLoopback Diagnostic Test CRC16 Calculation Error and Exception Responses Reversed BIT Order Used Bit Parameters Controller Status Byte Parameter Numbers Controller Parameters Word Parameters Instrument ID Parameters Volume O077-4 Profiler Status Byte Profiler Commands General Universal Input Input Range Remote RUN/HOLD Input Option Relay OutputSSR Drive/TTL Solid State Types Available Relay, SSR drive, solid state and DC Solid State SSR Drive/TTL Loop Control Alarm Control Performance Under Reference Conditions PerformanceReference Conditions S077-A Volume Physical EnvironmentalSee Performance Appendix B Summary of Displays Program Define Mode Parameters Configuration Mode Parameters AppendixC RaPID Control Feature AT OFF Alphabetical Index S077-IDX Volume Making a Soak Segment S077-IDX Volume Unpacking Procedure Word Parameters II/4-8