Base Mode | Omega CN1166 specification

161 -DIN RAMP/SOAK PROFILE CONTROLLER

PRODUCT MANUAL

VOLUME II

OPERATING INSTRUCTIONS

In normal operation, the operator must not remove the Ramp/Soak Profile Controller from its housing or have unrestricted access to the rear terminals, as this would provide potential contact with hazardous live parts.

Installation and configuration must be undertaken only by technically-competent servicing personnel. This is covered in Volume I of this manual.

CONTENTS

1	BASE MODE	1-1
1.1	DISPLAY SEQUENCE - NO PROGRAM RUNNING	1-1
1.2	STARTING A PROGRAM	1-2
1.3	PUTTING A PROGRAM IN HOLD	1-2
1.4	RELEASING A PROGRAM FROM HOLD	1-2
1.5	ABORTING A PROGRAM	1-2
1.6	DISPLAY SEQUENCE - PROGRAM RUNNING	1-3
1.7	RaPID CONTROL FEATURE	1-4
1.8	PRE-TUNE FEATURE	1-4
1.9	ENGAGING BOTH PRE-TUNE AND RaPID FEATURES	1-5
1.10	INDICATION OF PRE-TUNE AND RaPID STATUS	1-5
1.11	VIEWING THE HARDWARE DEFINITION CODE	1-6
1.12	MANUAL CONTROL	1-7

PM077-V2

Volume II

(i)

Image 27

Omega CN1166 manual Base Mode

Contents

Page Page RAMP/SOAK Profile Volume Operating Instructions Volume Installation & Configuration Instructions Contents PANEL-MOUNTING the Controller Unpacking Procedure Connections and Wiring Rear Terminal Connections RTD Inputs Mains Line Input2 24V Nominal AC/DC Supply Thermocouple Input SSR Drive Outputs Linear InputsRemote Run/Hold Input Relay Outputs 11 RS485 Serial Communications Link DC Outputs Removing the Profile Controller from ITS Housing Internal Links and Switches Removing the Output 2/Output 3 Option PCBs REMOVING/REPLACING the Output 2/OUTPUT 3 Option PCBs Replacing the Instrument in ITS Housing Input Type Selection of Input Type and Output 1 Type CPU PCB Relay/SSR Drive/Solid State Output Primary Output Output 1 Type Output 2 TYPE/OUTPUT 3 Type Hardware Definition Code Entry Into Configuration Mode Wit h Hardw are Definit ion Code displayed Configurat ion Mode Hardware Definition Code Input/Output Type Selection Option Selection Wit h Hardw are Definit ion Code displayed Configuration Mode Parameters Parameter AL1 OFF, AL2 OFF Parameter Page Exit from Configuration Mode Base Mode Alphabetic Index Controller SET-UP ModeProgram Definition Mode CREATING/EDITING a Program Modbus Communications Display Sequence no Program Running Base Mode Aborting a Program Starting a ProgramPutting a Program in Hold Releasing a Program from Hold Read Only whilst Program is running/held Display Sequence Program Running PRE-TUNE Feature RaPID Control Feature Indication of PRE-TUNE and RaPID Status Engaging Both PRE-TUNE and RaPID Features RaPID Status when Hardware Definition Code has the following significance Viewing the Hardware Definition Code Press till front panel shows Press or to change display to Manual Control Controller SET-UP Mode Lower display = Parameter Details Parameter Function Adjustment Range Default Value ON/OFF Parameter Function Adjustment Range Default Value Power Alarm Operation Deviation When this display shows Exit from Controller SET-UP Mode Entry Program Definition Mode CREATING/EDITING a Program Basic Guidelines Creating a Program To make a Soak segment Defining Segments Rate Mode Defining Segments Time Mode Program Options T p o i n t Guaranteed Soak Band Segment Event Status Press key To display Exit from Program Define Mode Default Values and Adjustment Ranges Introduction Modbus Functions SupportedMessage Formats CRC16 Read Coil Status Read n Bits 01/02 Force Single Coil Write 1 Bit Read Holding Registers Read n Words 03/04 Preset Single Register Write 1 Word 06 B Loopback Diagnostic TestPreset Multiple Registers Write n Words 16 B CRC16 Calculation Error and Exception Responses Reversed BIT Order Used Bit Parameters Controller Status Byte Parameter Numbers Controller Parameters Word Parameters Instrument ID Parameters Volume O077-4 Profiler Status Byte Profiler Commands General Universal Input Input Range Remote RUN/HOLD Input Option Solid State OutputRelay SSR Drive/TTL Types Available Relay, SSR drive, solid state and DC Solid State SSR Drive/TTL Loop Control Alarm Control Performance Reference ConditionsPerformance Under Reference Conditions S077-A Volume Environmental See PerformancePhysical Appendix B Summary of Displays Program Define Mode Parameters Configuration Mode Parameters AppendixC RaPID Control Feature AT OFF Alphabetical Index S077-IDX Volume Making a Soak Segment S077-IDX Volume Unpacking Procedure Word Parameters II/4-8