Manuals / Omega / Video Game / Controller

Omega CN1166 manual Segment Parameters - Program

Models: CN1166

1 88

Download 88 pages 37.01 Kb

Page 64

Manual background

No.	Parameter	Notes

Segment Parameters - Program 3

1300	Run Program (value = Delayed Start value)	Write only

1301	No. of Cycles Programmed	1 to 9999 plus 10000 (INF)

1302	Timebase	0	= hours/mnutes, 1 = minutes/seconds

1303	Guaranteed Soak Band value	0	(OFF), 1 to span

1304	Final Setpoint values	Segment 1 at address 1304
to	(Soak = -32768, End = -16384)
1319		Segment 16 at address 1319

1320	Rate values (Soak = -32768, End =	Segment 1 at address 1320
to	-16384)
1335		Segment 16 at address 1335

1336	Time values	Segment 1 at address 1336
to
1351		Segment 16 at address 1351

1352	Event Marker settings	Bit 0 = Event 16 Bit 15 = Event 1

Segment Parameters - Program 4

1400	Run Program (value = Delayed Start value)	Write only

1401	No. of Cycles Programmed	1 to 9999 plus 10000 (INF)

1402	Timebase	0 = hours/minutes, 1 =
		minutes/seconds

1403	Guaranteed Soak Band value	0 (OFF), 1 to span

1404	Final Setpoint values	Segment 1 at address 1404
to	(Soak = -32768, End = -16384)
1419		Segment 16 at address 1419

1420	Rate values (Soak = -32768, End =	Segment 1 at address 1420
to	-16384)
1435		Segment 16 at address 1435

1436	Time values	Segment 1 at address 1436
to
1451		Segment 16 at address 1451

Some of the parameters which do not apply to a particular instrument configuration (e.g. PB2 on a single output instrument) will accept reads & writes. Others will accept reads only, and will return an exception if an attempt is made to write values to them. The values read will in all cases be undefined. It is the user’s responsibility to make sure that values read reflect a possible state of the instrument.

4-10

Volume II

O077-4

Image 64

Omega CN1166 manual Segment Parameters - Program

Contents

Page Page 1 -DIN RAMP/SOAK PROFILECONTROLLER Product ManualHOW TO USE THIS MANUAL VOLUME INSTALLATION & CONFIGURATION INSTRUCTIONSVOLUME OPERATING INSTRUCTIONS t ra in e d , e q u ip p e d a n d a u t h o ris e d t o d o s o161 -DIN RAMP/SOAK PROFILE CONTROLLER PRODUCT MANUAL VOLUME INSTALLATION & CONFIGURATION INSTRUCTIONSCONTENTS INSTALLATION1.2 PANEL-MOUNTING THE CONTROLLER 1.1 UNPACKING PROCEDURE1 INSTALLATION 1.3 CONNECTIONS AND WIRING POWER drive,solid state orDC,alarm outputOutput 3isused eitherasalarm output POWER CONNECTION1.3.1 Mains Line Input 1.3.2 24V Nominal AC/DC Supply1.3.3 Thermocouple Input 1.3.4 RTD Inputs1.3.5 Linear Inputs 1.3.6 Remote Run/Hold Input1.3.7 Relay Outputs 1.3.8 SSR Drive Outputs1.3.10 DC Outputs 1.3.11 RS485 Serial Communications Link2 INTERNAL LINKS AND SWITCHES 2.1 REMOVING THE PROFILE CONTROLLER FROM ITS HOUSINGRS485 Com m unic a tions Op tion PC or Re m ote Run/Hold Op tion PCB Outp ut 3 Op tion PCBFigure 2-2 Removing the Output 2/Output 3 Option PCBs VolumeS077-2 2.4 REPLACING THE INSTRUMENT IN ITS HOUSING 2.2 REMOVING/REPLACING THE OUTPUT 2/OUTPUT 3 OPTION PCBsREPLACEMENT 2.5 SELECTION OF INPUT TYPE AND OUTPUT 1 TYPE2.5.1 Input Type REMOVAL2.5.2 Primary Output Output 1 Type Figure 2-4 CPU PCB Relay/SSR Drive/Solid State Output2.6 OUTPUT 2 TYPE/OUTPUT 3 TYPE 3 CONFIGURATION MODE 3.1 ENTRY INTO CONFIGURATION MODEWithin 30 secs. as 1st key action after power-up In Configurat ion ModeIn Configurat ion Mode Use these keys also to return to Configuration ModeWit h Hardw are Definit ion Code displayed Current Hardware3.3 OPTION SELECTION Wit h Hardw are Definit ion Code displayed 3.4 CONFIGURATION MODE PARAMETERSTo display One of three Parameter Page Identifier Parameter 3.5 EXIT FROM CONFIGURATION MODE SIMU LTAN EO U SLYOPERATING INSTRUCTIONS BASE MODE161 -DIN RAMP/SOAK PROFILE CONTROLLER PRODUCT MANUAL VOLUME CONTENTSAPPENDIX A PRODUCT SPECIFICATION APPENDIX B SUMMARY OF DISPLAYS APPENDIX C RAPID CONTROL FEATURE Alphabetic Index2 CONTROLLER SET-UP MODE 3 PROGRAM DEFINITION MODE1 BASE MODE 1.1 DISPLAY SEQUENCE - NO PROGRAM RUNNINGSetpoint Strategy = 1, adjustable if SP Lock is OFF Shows/enables selection of program Program Number in the range 11.2 STARTING A PROGRAM 1.3 PUTTING A PROGRAM IN HOLD1.4 RELEASING A PROGRAM FROM HOLD 1.5 ABORTING A PROGRAM1.6 DISPLAY SEQUENCE - PROGRAM RUNNING Omitted if Manual Control is disabled see SectionNOTE All displays are Read Only whilst program is running/held Omitted if No. Of Cycles = 1 i.e. No cycling1.8 PRE-TUNE FEATURE 1.7 RaPID CONTROL FEATUREPress simultaneously twice in quick succession 1.9 ENGAGING BOTH PRE-TUNE AND RaPID FEATURES 1.10 INDICATION OF PRE-TUNE AND RaPID STATUSRaPID status when Pre-Tune engagedRaPID Status when Pre-Tune disengaged1.11 VIEWING THE HARDWARE DEFINITION CODE O utput TypeInput TypePress till front panel shows Press or to change display to 1.12 MANUAL CONTROLPress till front panel shows 2 CONTROLLER SET-UP MODE To display Press simultaneously when display shows to displayNOTE Default factory-set lock code is Set upper display to Controller Define lock codeOutput 2 only Outputs 1 Lower display =Output 1 only 2.1 PARAMETER DETAILS Adjustment Range DefaultParameter FunctionAdjustment Range DefaultParameter FunctionPower OutputPowerProcess High Alarm Process High Alarmdirect-acting reverse-actingPROCESS HIGH ALARM Alarm inactiveAlarm active ALARM2.2 EXIT FROM CONTROLLER SET-UP MODE When this display showsPress simultaneously To display3.1 ENTRY 3 PROGRAM DEFINITION MODE - CREATING/EDITING A PROGRAM3.2 CREATING A PROGRAM 3.2.1 Basic Guidelines3.2.2 Defining Segments - Rate Mode To make a Soak segmentMove to next segment NOTE Ramp rate is in units/hour if3.2.3 Defining Segments - Time Mode To make a Soak segmentMove to next segment To make End segmentan3.2.4 Program Options In the range 1 to 9999 plus 1 = no cycling= cycle indefinitely till aborted/held See Subsection See Subsection See Subsection In the range 03.2.5 Guaranteed Soak Band GUARANTEED GuaranteedENABLED MANUAL GUARANTEED SOAKDISPLAY 3.2.6 Segment Event StatusDISPLAY Press key To displayInitial display Segment 1 Event Indicator = ON Segment 2 Event Indicator = OFF3.3 DEFAULT VALUES AND ADJUSTMENT RANGES 3.4 EXIT FROM PROGRAM DEFINE MODEWhen this display shows Press simultaneously4 MODBUS COMMUNICATIONS 4.1 INTRODUCTION4.2 MODBUS FUNCTIONS SUPPORTED 4.3 MESSAGE FORMATSA. Read Coil Status Read n Bits 01/02Addr. of AddrB. Read Holding Registers Read n Words 03/04 C. Force Single Coil Write 1 Bit1st Word No. of wordsD. Preset Single Register Write 1 Word E. Loopback Diagnostic TestF. Preset Multiple Registers Write n Words 16 B 06 BG. Error and Exception Responses H. CRC16 CalculationAddr. Func. Exception No CRC16Normal Bit Order Reversed Bit OrderREVERSED BIT ORDER USED Most significant byte4.4 PARAMETER NUMBERS A. Bit Parameters Controller Status ByteController Parameters B. Word ParametersProgram Parameters Instrument ID Parameters Segment Parameters - ProgramSegment Parameters - Program ParameterSegment Parameters - Program Segment Parameters - ProgramParameter 4.6 PROFILER COMMANDS 4.5 PROFILER STATUS BYTEBit Number 15 14 13 12 11APPENDIX A PRODUCT SPECIFICATION UNIVERSAL INPUT GeneralResistance Temperature Detector RTD and DC mV Ranges selectable REMOTE RUN/HOLD INPUT OPTION OUTPUT GeneralRelay SSR Drive/TTLGeneral OUTPUTRelay Solid State Relay OUTPUT GeneralSSR Drive/TTL ALARM CONTROL LOOP CONTROLPERFORMANCE Reference Conditions Performance Under Reference ConditionsDC Outputs - Accuracy See PERFORMANCE ENVIRONMENTALPHYSICAL Base Mode Parameters APPENDIX B SUMMARY OF DISPLAYSController Set-Up Mode Parameters Controller Set-Up Mode Parameters Continued Program Define Mode ParametersConfiguration Mode Parameters MiscellaneousAppendixC RaPID Control Feature START-UPDISTURBANCE SETPOINT CHANGESThe responses to RaPID being engaged are Pre-TuneResponse IndicationALPHABETICAL INDEX Page Page Page I/1-1 Unpacking ProcedureWord Parameters II/4-8