Segment Event Status | Omega CN1166 specification

3.2.6Segment Event Status

For every segment in a program there is an event indicator. This may be set ON or OFF for that segment. The status for the segments in the currently-selected program appears in the following form in the upper display:

DISPLAY 1

ON

OFF

ON

OFF

Segment1

Segment2

Segment3

Segment4

Segment5

Segment6

Segment7

Segment8

DISPLAY 2

ON

OFF

ON

OFF

Segment9

Segment10

Segment11

Segment12

Segment13

Segment14

Segment15

Segment16

The first display shows the current event status for Segments 1 - 8 and the second display shows the current event status for Segments 9 - 16. Each event marker may be set ON (Up key) or OFF (Down key) in order of segment number. Only the event indicators for the segments in the program are displayed. If the program has less than 16 segments (including the End Segment), the non-applicable display positions are blank; if the program has eight segments or less, the second display is not included.. The lower display shows the current segment number. Thus, the key sequence to define the event markers for Segments 1 - 8 could be:

3-7

Volume II

O077-3

Image 52

Omega CN1166 manual Segment Event Status

Contents

Page Page RAMP/SOAK Profile Volume Installation & Configuration Instructions Volume Operating Instructions Contents Unpacking Procedure PANEL-MOUNTING the Controller Connections and Wiring Rear Terminal Connections Mains Line Input 2 24V Nominal AC/DC SupplyThermocouple Input RTD Inputs Linear Inputs Remote Run/Hold InputRelay Outputs SSR Drive Outputs DC Outputs 11 RS485 Serial Communications Link Internal Links and Switches Removing the Profile Controller from ITS Housing Removing the Output 2/Output 3 Option PCBs Replacing the Instrument in ITS Housing REMOVING/REPLACING the Output 2/OUTPUT 3 Option PCBs Selection of Input Type and Output 1 Type Input Type Primary Output Output 1 Type CPU PCB Relay/SSR Drive/Solid State Output Output 2 TYPE/OUTPUT 3 Type Entry Into Configuration Mode Hardware Definition Code Configurat ion Mode Wit h Hardw are Definit ion Code displayed Option Selection Hardware Definition Code Input/Output Type Selection Configuration Mode Parameters Wit h Hardw are Definit ion Code displayed Parameter AL1 OFF, AL2 OFF Parameter Page Exit from Configuration Mode Base Mode Controller SET-UP Mode Program Definition Mode CREATING/EDITING a ProgramModbus Communications Alphabetic Index Base Mode Display Sequence no Program Running Starting a Program Putting a Program in HoldReleasing a Program from Hold Aborting a Program Display Sequence Program Running Read Only whilst Program is running/held RaPID Control Feature PRE-TUNE Feature Engaging Both PRE-TUNE and RaPID Features Indication of PRE-TUNE and RaPID Status RaPID Status when Viewing the Hardware Definition Code Hardware Definition Code has the following significance Manual Control Press till front panel shows Press or to change display to Controller SET-UP Mode Lower display = Parameter Function Adjustment Range Default Value Parameter Details ON/OFF Parameter Function Adjustment Range Default Value Power Alarm Operation Deviation Exit from Controller SET-UP Mode When this display shows Program Definition Mode CREATING/EDITING a Program Entry Creating a Program Basic Guidelines Defining Segments Rate Mode To make a Soak segment Defining Segments Time Mode Program Options Guaranteed Soak Band T p o i n t Segment Event Status Press key To display Default Values and Adjustment Ranges Exit from Program Define Mode Modbus Functions Supported IntroductionMessage Formats Read Coil Status Read n Bits 01/02 CRC16 Read Holding Registers Read n Words 03/04 Force Single Coil Write 1 Bit Loopback Diagnostic Test Preset Single Register Write 1 Word 06 BPreset Multiple Registers Write n Words 16 B Error and Exception Responses CRC16 Calculation Reversed BIT Order Used Parameter Numbers Bit Parameters Controller Status Byte Word Parameters Controller Parameters Instrument ID Parameters Volume O077-4 Profiler Commands Profiler Status Byte Universal Input General Input Range Remote RUN/HOLD Input Option Output RelaySSR Drive/TTL Solid State Types Available Relay, SSR drive, solid state and DC Solid State SSR Drive/TTL Alarm Control Loop Control Reference Conditions PerformancePerformance Under Reference Conditions S077-A Volume See Performance EnvironmentalPhysical Appendix B Summary of Displays Program Define Mode Parameters Configuration Mode Parameters AppendixC RaPID Control Feature AT OFF Alphabetical Index S077-IDX Volume Making a Soak Segment S077-IDX Volume Unpacking Procedure Word Parameters II/4-8