Manuals / Brands / Car Audio and Video / Car Video System / Panasonic / Car Audio and Video / Car Video System

Panasonic BT-LH2170E, BT-LH2170P notes, <Note, (continued), Closed caption (CC) display, IMD (in monitor display) display

1 80

Download 80 pages, 7.67 Mb

On-screen Display (continued)

Closed caption (CC) display

Closed caption

display area

(When the specified window extends beyond the entire screen)

•This unit can display closed captions with an SDI or VIDEO signal input.

•Closed captions comply with the following standards.

•Composite Standard EIA/CEA-608 (VBI), OP-42

•SD-SDI CC Standard EIA/CEA-608 (ANC/VBI), OP-42

•HD-SDI CC Standard EIA/CEA-608 (708),

EIA/CEA-708, OP-47

•The EIA/CEA-708 Standard allows simultaneous display of closed captions at a specified location on up to eight windows.

•Closed captions are displayed on an area inside the screen that is smaller than the entire screen.

(Refer to the following notes.)

•The display settings can be configured in the menus. The menu also allow you to select closed caption type, display channel (EIA/CEA-608) and display service (EIA/CEA-708). (→page 46)

<Note>

•The specified window position is displayed at a position in the display area according to the closed caption information.

•The window may extend beyond the display area depending on the position and size of the specified window. Such a win- dow will be displayed but a window that extends beyond the entire screen will be repositioned inside the screen area.

IMD (in monitor display) display

●●Normal operating mode								• This monitor supports the TSL UMD PROTOCOL (Ver. 3.1
								and Ver. 4.0) and allows you to display text and the tally indi-

								cation on the monitor using the RS-485 interface.
								• For information on how to set IMD and communications, refer
								to pages 47, 48, 63.
								• In TWO WINDOW mode, it will display SDI1 and SDI2 in
								separate in monitor display (IMD) windows.

				CAM1

	Tally 1			Text		Tally 2
●●In TWO WINDOW mode

CAM1CAM2

19

Contents

Model No ENGLISH Read this first ! (for BT-LH2170P) IMPORTANT SAFETY INSTRUCTIONS Read this first ! (for BT-LH2170E) Read this first ! (for BT-LH2170E) (continued) FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY FOR CONTINENTAL EUROPE, ETC FOR U.K. ONLY Not to be used in the U.K EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS 1.Applicable standards and operating environment 2.Pre-requisiteconditions to achieving compliance with the above standards 3.Performance level Transportation precautions About this instruction manual Precautions for Use Table of Contents Standard accessories · Optional units Outline Dimensions Controls and Their Functions Controls and Their Functions (continued) Front panel 1POWER <8> switch 2INPUT SELECT buttons 3FUNCTION button FUNCTION1 to FUNCTION5: Rear panel 1SDI terminal *1Daisy-chain: 2 VIDEO terminal (BNC) *2*3 3DVI-Iterminal Power supply Detaching and Attaching the Stand On-screenDisplay On-screenDisplay (continued) 3.To close a menu, press <MENU Picture adjusting (PICTURE) menu display 1.Press rotary knob <PICTURE> when no menu is dis- played 2.To close a menu, press <MENU Audio volume bar meter display Display color Time code (TC) display In LTC and VITC display mode In LUB and VUB display modes Closed caption (CC) display notes IMD (in monitor display) display How to Use the On Screen Menu How to Use the On Screen Menu (continued) Picture adjusting (PICTURE) menu Adjustable range Name Function User Data Main Menu Main Menu (continued) 2D/3D ASSIST Setting Description 3D ASSIST CENTER*2 CROSS GPI MARKER1 *5 GPI MARKER2 *5 MARKER TYPE *7 MARKER types „„16:9 marker „„4:3 marker VISTA marker, 2:1 marker, CNSCO marker Area marker VIDEO CONFIG GAMMA SELECT *1*2 FILM GAMMA COLOR TEMP SHARPNESS MODE *5 *6 I-PMODE *7 MONO *2 ANAMO *8 SD ASPECT *2 SCAN *2*8 „„WB (WHITE BALANCE) adjustment mode COLOR TEMP.*10 GAIN BIAS „„Direct adjustment mode SYSTEM CONFIG MENU POSITION STATUS DISPLAY INPUT NAME SETUP „„INPUT NAME SETUP 3.Turn the rotary knob <PICTURE> to select the characters you want to change*7 and press the rotary knob <PIC TURE> to confirm them „„CALIBRATION „„Equipment required for CALIBRATION Pin RS-232Cinput (9 pins) Performing AUTO CALIBRATION 3.Select [YES] and press the rotary knob <PICTURE>. This starts calibration 4.Turn the power off and then on after performing auto calibration RESET operation FUNCTION FUNCTION1 FUNCTION5 FUNCTION DISPLAY *8 „„FUNCTION setting restrictions Inoperable Condition or Mode ZEBRA LEVEL „„Functions displayed during FUNCTION button operation Display AUDIO MUTE 2D/3D ASSIST „„FUNCTION skip function 3.Press <RETURN/VOLUME „„HV DELAY „„SUB WINDOW •FULL Note on FULL/PART selection „„WFM/VECTOR Press the <FUNCTION> button to (Y→R→G→B) which the WFM/VECTOR function „„ZEBRA „„Y MAP „„TWO WINDOW •When two screens are displayed, the left screen is the sync reference •When a signal is input only to one screen, that signal is the sync reference „„PICTURE ASSIST The signal selected with [INPUT] is displayed on a single screen „„PIXEL TO PIXEL and PIXEL POSITION Item PIXEL TO PIXEL*13*14 „„PIXEL POSITION display position sequence „„CROSS HATCH „„FOCUS-IN-RED Press the <FUNCTION> button to which the FOCUS-IN-REDfunction has been assigned GPI GPI CONTROL INPUT SELECT NTSC SETUP COMPONENT LEVEL „„RGB-COMP AUDIO INPUT SELECT GROUP SELECT SELECT L *1 *2 *3 *4 SELECT R *1 *4 *5 *6 DISPLAY SETUP VECTOR MODE VECTOR SCALE FONT SIZE MODE SELECT CAPTION SERVICE IN MONITOR DISPLAY CHAR. COLOR CONTROL CONTROL LOCAL ENABLE *1 PROTOCOL VER.*2 RS-485ID SETUP RS-485STX&ETX 3D Assist Mode [3D ASSIST] MIRROR SDI(L) OFF SDI(R) COMPARISON (Composition Check) [3D ASSIST] COMPARISON SBYS <Assist Point CONVERGENCE (Convergence Check) [3D ASSIST] COLOR SIZE ZOOM F-IN-R VERTICAL MARKER1 440 MARKER2 98 Lines [3D ASSIST] OVERLAY STANDARD MKR POSI 0 MKR WDTH 3% MKR POSI MKR WIDTH Setting Item Restrictions Setting Item Restrictions (continued) ü*4 „„List of Setting Item Restrictions in 3D Assist Mode (ü: Can be set) Page REMOTE Specifications REMOTE Specifications (continued) REMOTE STANDBY *4*5 Restrictions „„Priority of assigned functions RS-232Cinput terminal „„Connectors and signals RS-232Cinput terminal Connector: D-SUB 9-pin(female) number „„Command format „„Communication parameters RS-485input/output terminal External control device IN (input) OUT 3.Error response „„Setting command Send commands Command name Return Page Page „„Query commands Response data Page Page Maintenance Inspections Error and Warning Information Maintenance Specifications Specifications (continued) „„List of supported video input signal formats in 2D mode (ü: Supported) Input signal format SDI1 SDI2 „„List of Compatible 3G-SDIInput Signal Formats Input level Pixel resolution Bit SDI1/2 (SIMULTANEOUS) „„List of Signal Formats Supported in 3D Assist Mode (ü: Supported) Input Signal Format/ Status displays „„Closed Caption Decoding Supported Signals Composite SD-SDI HD-SDI „„INT-SG(Internal chart for adjustment) BLACK -4% BLACK +4% BLACK Index Index (continued) OVERLAY 53 Picture adjusting menu PICTURE ASSIST For business users in the European Union Information on Disposal in other Countries outside the European Union ENGLISH „„Adobe® Reader® is required to read PDF files It can be downloaded from the home page of Adobe Systems