Panasonic BT-LH2170E, BT-LH2170P 69

REMOTE Specifications (continued)

No	Command parameter		Description				Response data
64	QMC	IN	MONITOR	DISPLAY	0: CMD (RS-485 setting)		1: WHITE	2: BLUE
		CHAR. COLOR			3:GREEN	4:YELLOW	5:CYAN	6:RED
					7:GRAY	8:MAGENTA
65	QMV	IN	MONITOR	DISPLAY	0:Ver3.1	1:Ver4.0
		VERSION
66	QAI	INPUT SELECT			0:AUTO	1:ANALOG
67	QGS	GROUP SELECT			0:1 to 8	1:9 to 16
68	QSL	SELECT L			0:1ch/9ch	1:2ch/10ch	2:3ch/11ch	3:4ch/12ch	4:5ch/13ch
					5:6ch/14ch	6:7ch/15ch	7:8ch/16ch
69	QSR	SELECT R			0:1ch/9ch	1:2ch/10ch	2:3ch/11ch	3:4ch/12ch	4:5ch/13ch
					5:6ch/14ch	6:7ch/15ch	7:8ch/16ch
70	QMT	AUDIO MUTE			0:OFF	1:ON
71	QOS	AUDIO OUT SEL.			0:SDI1	1:SDI2
72	QID	MODEL CHECK			BT-LH2170

Contents

Model No ENGLISH Read this first ! (for BT-LH2170P) IMPORTANT SAFETY INSTRUCTIONS Read this first ! (for BT-LH2170E) Read this first ! (for BT-LH2170E) (continued) FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY FOR CONTINENTAL EUROPE, ETC FOR U.K. ONLY Not to be used in the U.K EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS 1.Applicable standards and operating environment 2.Pre-requisiteconditions to achieving compliance with the above standards 3.Performance level Transportation precautions About this instruction manual Precautions for Use Table of Contents Standard accessories · Optional units Outline Dimensions Controls and Their Functions Controls and Their Functions (continued) Front panel 1POWER <8> switch 2INPUT SELECT buttons 3FUNCTION button FUNCTION1 to FUNCTION5: Rear panel 1SDI terminal *1Daisy-chain: 2 VIDEO terminal (BNC) *2*3 3DVI-Iterminal Power supply Detaching and Attaching the Stand On-screenDisplay On-screenDisplay (continued) 3.To close a menu, press <MENU Picture adjusting (PICTURE) menu display 1.Press rotary knob <PICTURE> when no menu is dis- played 2.To close a menu, press <MENU Audio volume bar meter display Display color Time code (TC) display In LTC and VITC display mode In LUB and VUB display modes Closed caption (CC) display notes IMD (in monitor display) display How to Use the On Screen Menu How to Use the On Screen Menu (continued) Picture adjusting (PICTURE) menu Adjustable range Name Function User Data Main Menu Main Menu (continued) 2D/3D ASSIST Setting Description 3D ASSIST CENTER*2 CROSS GPI MARKER1 *5 GPI MARKER2 *5 MARKER TYPE *7 MARKER types „„16:9 marker „„4:3 marker VISTA marker, 2:1 marker, CNSCO marker Area marker VIDEO CONFIG GAMMA SELECT *1*2 FILM GAMMA COLOR TEMP SHARPNESS MODE *5 *6 I-PMODE *7 MONO *2 ANAMO *8 SD ASPECT *2 SCAN *2*8 „„WB (WHITE BALANCE) adjustment mode COLOR TEMP.*10 GAIN BIAS „„Direct adjustment mode SYSTEM CONFIG MENU POSITION STATUS DISPLAY INPUT NAME SETUP „„INPUT NAME SETUP 3.Turn the rotary knob <PICTURE> to select the characters you want to change*7 and press the rotary knob <PIC TURE> to confirm them „„CALIBRATION „„Equipment required for CALIBRATION Pin RS-232Cinput (9 pins) Performing AUTO CALIBRATION 3.Select [YES] and press the rotary knob <PICTURE>. This starts calibration 4.Turn the power off and then on after performing auto calibration RESET operation FUNCTION FUNCTION1 FUNCTION5 FUNCTION DISPLAY *8 „„FUNCTION setting restrictions Inoperable Condition or Mode ZEBRA LEVEL „„Functions displayed during FUNCTION button operation Display AUDIO MUTE 2D/3D ASSIST „„FUNCTION skip function 3.Press <RETURN/VOLUME „„HV DELAY „„SUB WINDOW •FULL Note on FULL/PART selection „„WFM/VECTOR Press the <FUNCTION> button to (Y→R→G→B) which the WFM/VECTOR function „„ZEBRA „„Y MAP „„TWO WINDOW •When two screens are displayed, the left screen is the sync reference •When a signal is input only to one screen, that signal is the sync reference „„PICTURE ASSIST The signal selected with [INPUT] is displayed on a single screen „„PIXEL TO PIXEL and PIXEL POSITION Item PIXEL TO PIXEL*13*14 „„PIXEL POSITION display position sequence „„CROSS HATCH „„FOCUS-IN-RED Press the <FUNCTION> button to which the FOCUS-IN-REDfunction has been assigned GPI GPI CONTROL INPUT SELECT NTSC SETUP COMPONENT LEVEL „„RGB-COMP AUDIO INPUT SELECT GROUP SELECT SELECT L *1 *2 *3 *4 SELECT R *1 *4 *5 *6 DISPLAY SETUP VECTOR MODE VECTOR SCALE FONT SIZE MODE SELECT CAPTION SERVICE IN MONITOR DISPLAY CHAR. COLOR CONTROL CONTROL LOCAL ENABLE *1 PROTOCOL VER.*2 RS-485ID SETUP RS-485STX&ETX 3D Assist Mode [3D ASSIST] MIRROR SDI(L) OFF SDI(R) COMPARISON (Composition Check) [3D ASSIST] COMPARISON SBYS <Assist Point CONVERGENCE (Convergence Check) [3D ASSIST] COLOR SIZE ZOOM F-IN-R VERTICAL MARKER1 440 MARKER2 98 Lines [3D ASSIST] OVERLAY STANDARD MKR POSI 0 MKR WDTH 3% MKR POSI MKR WIDTH Setting Item Restrictions Setting Item Restrictions (continued) ü*4 „„List of Setting Item Restrictions in 3D Assist Mode (ü: Can be set) Page REMOTE Specifications REMOTE Specifications (continued) REMOTE STANDBY *4*5 Restrictions „„Priority of assigned functions RS-232Cinput terminal „„Connectors and signals RS-232Cinput terminal Connector: D-SUB 9-pin(female) number „„Command format „„Communication parameters RS-485input/output terminal External control device IN (input) OUT 3.Error response „„Setting command Send commands Command name Return Page Page „„Query commands Response data Page Page Maintenance Inspections Error and Warning Information Maintenance Specifications Specifications (continued) „„List of supported video input signal formats in 2D mode (ü: Supported) Input signal format SDI1 SDI2 „„List of Compatible 3G-SDIInput Signal Formats Input level Pixel resolution Bit SDI1/2 (SIMULTANEOUS) „„List of Signal Formats Supported in 3D Assist Mode (ü: Supported) Input Signal Format/ Status displays „„Closed Caption Decoding Supported Signals Composite SD-SDI HD-SDI „„INT-SG(Internal chart for adjustment) BLACK -4% BLACK +4% BLACK Index Index (continued) OVERLAY 53 Picture adjusting menu PICTURE ASSIST For business users in the European Union Information on Disposal in other Countries outside the European Union ENGLISH „„Adobe® Reader® is required to read PDF files It can be downloaded from the home page of Adobe Systems