Main Menu  (continued)

Note on FULL/PART selection

This function is designed to enable comparison of identical formats input to the same input terminal. Input of different formats via different input lines may distort the sub-window (left side, still image) or make part of the image disappear from view. However, input of an identical format signal to the input terminal during still image acquisition will display correctly.

„„WFM/VECTOR

The WFM/VECTOR function enables display of the waveform and vector display. Use [DISPLAY SETUP] in [MAIN MENU] (main menu) to select WFM and VECTOR display.(→page 46)

Press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the WFM/VECTOR function has been assigned to switch displays in the following order.

[WFM/VECTOR OFF] → [WFM Y ON] → [WFM R ON] → [WFM G ON] → [WFM B ON] → [VECTOR×1/×2S/×2/×4/×8]

•To use the WFM/VECTOR function, it must be assigned to one of the <FUNCTION1> to <FUNCTION5> buttons. “WFM” signals are displayed in the following order: Y, R, G, B.

 

Press the same button again

 

Normal screen

WFM display

VECTOR display*12

Press the <FUNCTION> button to (Y→R→G→B)

 

which the WFM/VECTOR function

Press the same

 

has been assigned.

button again

WFM (waveform

display)

*12Displayed only for SDI signal input.

• The scale display is as shown below.

VECTOR

(vector display)

These examples show 16:9 aspect ratio images.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RED

MAGENTA

100 %

 

 

 

 

 

 

 

 

 

 

 

 

109 %

 

 

 

 

 

 

 

 

 

 

I axis

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A dotted line

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLUE

50 %

 

 

 

 

 

 

 

 

 

 

 

indicates for

YELLOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

each 10 %

 

 

 

 

 

 

 

 

 

 

The frame is approx.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.5 degrees and

 

 

 

 

 

 

 

 

 

 

 

 

increase.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

approx. 2.5%.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0 %

 

 

 

 

 

 

 

 

 

 

 

 

－4 %

GREEN

 

 

 

 

 

 

 

 

 

Q axis

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CYAN

The vertical lines in the frame are color coded to simplify identification.

39