Main Menu  (continued)

FUNCTION

 

 

Underlined values indicate factory defaults.

Submenu

Setting

Description

FUNCTION1 -

HV DELAY

Selects functions to be assigned to <FUNCTION1> - <FUNCTION5> (front panel

FUNCTION5

BLUE ONLY

buttons or the [FUNCTION] menu).

 

GAMMA SELECT

[HV DELAY] *1

 

SD ASPECT

This displays the blanking period.

 

SCAN

The display changes in the following order.

 

SUB WINDOW

[DELAY OFF] → [H DELAY] → [V DELAY] → [HV DELAY]

 

WFM/VECTOR

[BLUE ONLY] *1

 

MARKER

Cuts the red and green signals. Use this function to check phase (PHASE) and

 

WHITE BALANCE

chroma (CHROMA). This button toggles between ON and OFF.

 

PIXEL TO PIXEL

[GAMMA SELECT]  *2*3

 

PIXEL POSITION

Displays the gamma curve.

 

FOCUS-IN-RED

The display changes in the following order.

 

LEVEL METER

[GAMMA STANDARD] → [GAMMA FILM] → [GAMMA STDIO/PST] →

 

CROSS HATCH

[GAMMA CINEMA]

 

MONO

[SD ASPECT]  *2*3

 

BLACK MODE

Switches between [16:9] and [4:3].

 

TIME CODE

[SCAN]  *2*3

 

CLOSED CAPTION

Switches between [UNDER SCAN] and [NORMAL SCAN].

 

AUDIO MUTE

[SUB WINDOW] *1

 

AUDIO OUT SEL.

Sets the split-screen function.

 

ANAMO

The display changes in the following order.

 

TWO WINDOW

[SINGLE] → [FULL/PART] → [STILL]

 

Y MAP

[WFM/VECTOR] *2

 

PICTURE ASSIST

Displays waveform or vector display.

 

R COLOR

For details on the available operation items, refer to page 36.

 

G COLOR

[MARKER] *2*3*4

 

B COLOR

Display the marker.

 

ZEBRA

For details on the available operation items, refer to page 36.

 

ZEBRA LEVEL

[WHITE BALANCE]

 

2D/3D ASSIST

RGB can be directly adjusted under [GAIN]/[BIAS] in WHITE BALANCE only when

 

UNDEF

[VAR1] to [VAR3] are selected under [COLOR TEMP.].

 

 

[PIXEL TO PIXEL]

 

 

Turns the PIXEL TO PIXEL function On and Off.

 

 

[PIXEL POSITION]

 

(Factory defaults

Positions the display of signals when PIXEL TO PIXEL is on.

 

FUNCTION1:

The display changes in the following order.

 

WFM/VECTOR

[PIXEL TO PIXEL LEFT]→[PIXEL TO PIXEL CENTER]→

 

FUNCTION2:

[PIXEL TO PIXEL RIGHT]

 

TWO WINDOW

[FOCUS-IN-RED]*3*5

 

FUNCTION3:

Turns On/Off the function that highlights in red the portion of the image that is being

 

FOCUS-IN-RED

focused.

 

FUNCTION4:

[LEVEL METER] *2

 

TIME CODE

Turns the audio volume bar meter display On and Off.

 

FUNCTION5:

[CROSS HATCH] *2

 

LEVEL METER)

Displays the cross hatch grid.

 

 

The display changes in the following order.

 

 

[CROSS HATCH OFF] → [CROSS HATCH LOW] → [CROSS HATCH HIGH]

 

 

[MONO] *2*3

 

 

Switches between color and monochrome.

 

 

[BLACK MODE] *1*6

 

 

This mode is for correcting black level errors and checking the gradation of dark

 

 

areas.

 

 

The brightness of the backlight is reduced and the contrast is increased so that

 

 

up to 75 % of the input signal level has the same gamma curve as the [GAMMA

 

 

SELECT] setting. The signal level of 75% or higher is clipped.

*1 The settings are canceled when the power is turned OFF.

*2 When these settings are changed, the menu settings will also change. *3 The control settings do not operate during GPI operation.

*4 Not displayed when [16:9], [4:3] and [CENTER] are all [OFF] in the [MARKER] menu settings.

*5 During FOCUS-IN-RED operation, use the rotary knob <PICTURE> to change the detection sensitivity.

The setting range is from 1 to 30, with a higher numerical value resulting in higher detection sensitivity (the focus becomes less sharp).

*6 The bright picture is clipped. The back light and contrast cannot be adjusted.

34