Main Menu (continued)
PIXEL TO PIXEL and PIXEL POSITIONThe PIXEL TO PIXEL function allows you to check images at their actual pixel resolution. (HD signals only)
Press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the [PIXEL TO PIXEL] function has been assigned to turn the function on. Then press the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the [PIXEL POSITION] function has been assigned to position the display of signals. Each press of the button will change the display position of the signal.
Underlined values indicate factory defaults.
| Item | Setting |
|
| Description |
| PIXEL TO PIXEL*13*14 | OFF | Sets whether to display the screen display size at the input signal size. | ||
| ON | [OFF]Not displayed | [ON] Displayed. | |
|
| Compatible formats |
| |
|
| • Only available in the left screen when a PICTURE ASSIST function is on | ||
|
| 1080/60i, 1080/59.94i, 1080/50i, 1080/60p, 1080/59.94p, 1080/50p, 1080/30p, | ||
|
| 1080/29.97p, 1080/25p, 1080/24p, 1080/23.98p, 1080/25PsF, 1080/24PsF, | ||
|
| 1080/23.98PsF |
| |
|
| • Only available in the left screen and in | ||
|
| function is on |
| |
|
| 720/60p, 720/59.94p, 720/50p | ||
PIXEL POSITION | LEFT | Positions the display of signals [PIXEL TO PIXEL] is [ON]. | ||
| CENTER | [LEFT] | Left of screen |
|
| RIGHT | [CENTER] | Center of screen | |
|
| [RIGHT] | Right of screen | |
|
| • Normally, when the input signal is 720/60p, 720/59.94p or 720/50p in the single screen | ||
|
| mode, the number of pixels of the monitor panel is greater than the number of samples | ||
|
| of the input signal. Although the image can be set, it will be displayed at CENTER | ||
|
| (screen center) and cannot be displayed at any other position. | ||
*13The following settings are disabled when [PIXEL TO PIXEL] is ON.
•Setting [ANAMO] to [ON], and setting [SCAN] to [UNDER] in [VIDEO CONFIG]
•Any [HV DELAY] setting in [FUNCTION]
•[MARKER] display
*14Enabled during [SDI1], [SDI2], [HDMI], [YPBPR] and
PIXEL POSITION: → → → .....
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LEFT |
|
| CENTER |
|
|
| RIGHT | ||||
The CROSS HATCH function displays markers at regular vertical and horizontal intervals to facilitate composition and other tasks. The marker line width is 1 dot per line and the interval is 120 dots/120 lines or 60 dots/60 lines depending on the [SIZE] setting in the [MARKER] menu (→page 24).
Each press of the <FUNCTION1> to <FUNCTION5> (→page 12) button to which the CROSS HATCH has been assigned changes the display.
Each press of the <FUNCTION> button to which the CROSS HATCH function is assigned changes the display as shown. HD/SD (16:9) mode
|
|
| Press the |
|
|
|
|
|
|
|
|
|
|
| Press the |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
| same button |
|
|
|
|
|
|
|
|
|
|
| same button |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
| again |
|
|
|
|
|
|
|
|
|
|
|
| again |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SD (4:3) mode |
|
|
|
| Dim cross hatch |
|
|
| Bright cross hatch | |||||||||||||
|
|
|
|
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Press the same button again (to return to the original image without cross hatch)
42