Main Menu (continued)
VIDEO CONFIG
|
|
|
|
|
|
| The underlined values are factory defaults. |
Submenu | Setting |
|
|
|
| Description | |
| GAMMA SELECT *1*2 | STANDARD | Selects gamma curve. |
|
|
|
| |
| FILM | [STANDARD] | Standard mode (power of 2.2) | ||||
| STDIO/PST | [FILM] | Film mode |
|
|
|
|
| CINEMA | [STDIO/PST] | Color emphasis mode (power of 2.35) | ||||
|
| [CINEMA] | CINEMA mode (power of 2.6) | ||||
|
| • When [FILM] is selected, the |
|
|
| mark is displayed for the operating status. | |
|
|
|
|
| |||
| FILM GAMMA | VARICAM | Selects type of FILM gamma mode. | |||||
| OTHER | [VARICAM] For VARICAM use |
|
| [OTHER] For other cameras | ||
(Gumma curve image)
Brightness | OTHER |
Video Gamma |
VARICAM
|
|
| Input Level |
|
|
| |
| COLOR TEMP. | USER 0 to 63*3 | Selects color temperature. | |
| D93 | [USER 0 to 63] Adjustable settings 0 to 63 | |
| D65 |
| (equivalent to a color temperature range of 3,000 K to 9,300 K) |
| D56 | [D93] | Equivalent to a color temperature of 9,300 K |
| VAR1 | [D65] | Equivalent to a color temperature of 6,500K |
| VAR2 | [D56] | Equivalent to a color temperature of 5,600 K |
| VAR3 | [VAR1] | WB (White Balance) adjustment mode *4 |
|
| [VAR2] | WB (White Balance) adjustment mode *4 |
|
| [VAR3] | WB (White Balance) adjustment mode *4 |
| SHARPNESS MODE *5 *6 | HIGH | Selects the width of outline correction edge. | |
| LOW | [HIGH] | Narrow edge |
|
| [LOW] | Wide edge |
| SHARPNESS H *5 *6 | 0 to 30 | Sets horizontal outline correction. The item display moves to the lower part of the | |
|
| screen during adjustment. | |
| SHARPNESS V *5 *6 | 0 to 30 | Sets vertical outline correction. The item display moves to the lower part of the | |
|
| screen during adjustment. | |
*1 When the SUB WINDOW function is used, changes are not reflected to the still image in the main window. *2 This menu is grayed out when the same item is assigned to GPI and [GPI CONTROL] is set to [ENABLE]. *3 To select [USER 0 to 63]
A Press the rotary knob <PICTURE>. ([USER] changes to blue)
B Use the rotary knob <PICTURE> to select 0 to 63 and press the rotary knob <PICTURE>. *4 Selecting [VAR1], [VAR2] or [VAR3] engages the WB adjustment mode.(→page 29)
*5 The following sharpness values
A VIDEO system input (VIDEO) (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS H/SHARPNESS V: 0)
B HD inputs other than A above (the factory defaults are SHARPNESS MODE: HIGH and SHARPNESS H/SHARPNESS V: 0).
C SD inputs other than A above (the factory defaults are SHARPNESS MODE: LOW and SHARPNESS H/SHARPNESS V: 0). are available and the settings for the selected input signal is displayed. During selection, adjustment status is displayed below the [PICTURE] (picture adjusting) menu.
*6 When HD signals are input via SDI1 and SD signals via SDI2 or SD signals via SDI1 and HD signals via SDI2 in TWO WINDOW or PICTURE ASSIST function operation, changes in the sharpness setting from the menu affect only the left screen.
(Continued on next page)
27