Pioneer DJM-2000 Press the 2 button in the CH section, Press Effect and select Sampler

2 Press the [2] button in the [CH] section.

This selects the channel to which the effect is applied.

3 Press [EFFECT] and select [SAMPLER].

This selects the type of effect.

Effect Name	Descriptions
	Sound is created inside this unit, mixed to the sound of the channel

OSCILLATOR1 – 4 selected in the [CH] section, then output according to the [TRIGGER CH

	(SAMPLING/TRIGGER CH)] trigger.
	The sound of the channel selected at [TRIGGER CH (SAMPLING/TRIG-
SAMPLER	GER CH)] is sampled, mixed to the sound of the channel selected in the
	[CH] section, then output according to the [TRIGGER CH (SAMPLING/
	TRIGGER CH)] trigger.
	The pitch of the sound of the channel selected in the [CH] section is
PITCH	changed, mixed with the channel selected in the [CH] section, then out-
	put according to the [TRIGGER CH (SAMPLING/TRIGGER CH)] trigger.
GATE	The sound input at [CH] is output according to the [TRIGGER CH (SAM-
	PLING/TRIGGER CH)] trigger.

!It is not possible to select multiple effects simultaneously.

4 Press [TRIGGER (SAMPLING/TRIGGER)].

The [TRIGGER] menu appears.

5 At [TRIGGER CH (SAMPLING/TRIGGER CH)], select [CH3].

This selects the channel to be used as the effect trigger.

!When [SAME] is pressed, the same channel as the one selected in the [CH] section is selected as the trigger.

6 At [TRIGGER BAND], press [MID] and [HI].

This selects the frequency band set as the effect trigger.

Only [LOW] (the bass sound) is selected.

7 Press [ON/OFF].

This turns the effect on.

[ON/OFF] flashes when the effect is turned on.

8 Touch the control area.

[ ] appears at the point at which the panel was touched.

The [CH3] sound at the point in the control area that was touched is sampled. Triggered by the low frequency sound of [CH3], the sampled sound is mixed with the sound of [CH2] (which is continuing to play normally) and output from the [MASTER] terminals.

The effect changes when the position touched in the control area is changed.

!The effect turns off when [ON/OFF] is pressed again.

!The sampled sound is only valid while the control area is being touched.

!To switch from the [SIDECHAIN REMIX] to the [FREQUENCY MIX] mode, first press the [ON/OFF] button to turn the effect off, then press [MIX].

Using [HOLD]

When [HOLD] is turned on, effect’s parameter information is held even if the effect is turned off. The parameter information is cleared when [HOLD] is turned off.

!The parameter information and sampled sound are cleared when the effect is switched.

LIVE SAMPLER

The sound input to the [MIC] terminal or the sound output from the [MASTER] terminals can be sampled and played on a PRO DJ LINK–compatible Pioneer DJ player.

Connect this unit and PRO DJ LINK-compatible Pioneer DJ player in advance. For instructions on connections, see Connecting input terminals on page 7.

			1
			2
			3
			4
		5
			6
		7
			8
			9
1	SOURCE SELECT	Select the source to be sampled here.
2	REC VOLUME	Use these to adjust the volume for recording.
		The volume can be adjusted in the range –9 dB to +9 dB.
3	Status indicator	This indicates this unit’s status and whether or not sam-
		pling data is available.
4	Waveform display	This displays the sound as a waveform.
5	Playing address display	This displays the sound as a bar graph.
		This is only displayed when previewing the sound.

		The sound is played from the position at which the touch
6	Slider	panel was touched.
		This is only displayed when previewing the sound.
7	PRE-REC SAVE	The sound is sampled from a point 8 seconds before the
		button was pressed.
8	REC (REC STOP)	The sound is sampled for up to 8 seconds from the point at
		which the button is pressed.
9	PREVIEW (STOP)	Use this to preview the sampled sound over the head-
		phones.

Sampling the sound being played

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [REC (REC STOP)].

The sound of the channel selected at step 2 is sampled from the point at which [REC (REC STOP)] was pressed.

!Sampling is possible for up to 8 seconds.

!Sampling stops automatically once 8 seconds have elapsed after [REC (REC STOP)] was pressed.

4 Press [REC (REC STOP)].

Sampling stops. The sample saving screen is displayed.

Sampling the sound from the point 8 seconds before

1 Press [LIVE SAMPLER].

The [LIVE SAMPLER] screen appears on the touch panel.

2 Press [MIC] or [MASTER] in the [SOURCE SELECT].

This selects the channel to be sampled.

3 Press [PRE-REC SAVE].

The sound for the channel selected in step 2 is sampled from the point 8 seconds before [PRE-REC SAVE] was pressed.

!Sampling is possible for up to 8 seconds.

Previewing the sampled sound

1Press the [CUE] button to the left of the touch panel.

2Press [PREVIEW (STOP)].

The position being played is displayed at the playing address and slider displays.

!When the touch panel’s slider is touched, the sampled sound is played from that position.

Playing the sampled sound on the DJ player

Use PRO DJ LINK to access this unit from the DJ player.

The sampled sound (audio file) can be loaded and played on the DJ player.

INST FX

This effect changes in association with the [FILTER] controls for the individual channels.

1 Press one of the [INST FX] buttons.

This selects the type of effect.

The button that was pressed flashes.

!The same effect is set for [CH1] to [CH4].

2 Turn the [FILTER] control.

The effect is applied to the channel(s) for which the control(s) was (were) pressed.

Effect Name	Descriptions	FILTER (parameter 1)	PARAMETER
			(parameter 2)
	White noise generated	Sets the cut-off
	inside this unit is mixed
NOISE		frequency for the	Sets the volume of the
	in to the sound of the	filter through which the	white noise.
	channel via the filter
		white noise passes.
	and output.
	Lowers the pitch of the	Sets the amount of	Sets the balance
			between the original
ZIP	channel’s sound for	pitch shifting for lower-
			sound and the effect
	output.	ing the pitch.
			sound.
	Changes the channel’s	Sets the degree by	The further the control
			is turned clockwise,
CRUSH	sound to a crushed	which the input sound
			the more the effect is
	sound for output.	is crushed.
			stressed.
			The further the control
JET	Adds a flanger effect for	Sets the flanger effect.	is turned clockwise,
	output.		the more the effect is
			stressed.

English

En 15