Pioneer DJM-2000 operating instructions REV ROLL1, Send Return

REV ROLL1 2

Original

Effect turned on

1/1 reverse roll

Reversed and repeated

This function records the input sound at the point at which the [ON/OFF] but- ton is pressed, reverses the recorded sound and repeats it according to the beat button’s fraction.

Beat buttons (parameter 1)	These set the cycle for moving the phaser effect by 1/8 to 4/1
	with respect to the time of one BPM beat.
TIME (parameter 2)	This sets the cycle by which the phaser effect is moved.	English
	10 to 32000 (ms)
	The further the control is turned clockwise, the more the effect
LEVEL/DEPTH (param-	is stressed.
eter 3)	When turned all the way counterclockwise, only the original
	sound is output.
EFFECT FREQUENCY	Use these to set the balance between the original sound and
(parameter 4)	the effect sound for the different bands.

GATE1

Beat buttons (parameter 1)	The effect time is set from 1/8 to 4/1 with respect to 1 beat of
	BPM time.
TIME (parameter 2)	Use this to set the effect time.
	10 to 4000 (ms)
LEVEL/DEPTH (param-	Use this to set the balance between the original sound and
eter 3)	ROLL.
EFFECT FREQUENCY	Use these to set the balance between the original sound and
(parameter 4)	the ROLL for the different bands.

FILTER1

Level

MIN MAX

MIN MAX

MIN MAX

EFFECT FREQUENCY

Threshold

Time

Threshold

Threshold

Frequency

This function changes the filter’s cut-off frequency according to the beat button’s fraction.

Beat buttons (parameter 1)	These set the cycle for moving the cut-off frequency from 1/8 to
	4/1 with respect to 1 beat of BPM time.
	Use this to set the cycle at which the cut-off frequency is
TIME (parameter 2)	moved.
	10 to 32000 (ms)
LEVEL/DEPTH (param-	The further the control is turned clockwise, the more the effect
eter 3)	is stressed.
EFFECT FREQUENCY	These set the balance between the original sound and the
(parameter 4)	effect sound for the different bands.

TRANS1

MIN MAX

1/1 beat Time

	Cut	Cut
MIN	MAX

	Cut	Cut
MIN	MAX

EFFECT FREQUENCY

This function cuts the sound according to the beat button’s fraction.

The amount of the sound to be cut can be changed at [EFFECT FREQUENCY].

Beat buttons (parameter 1)	These set the 1/8 to 4/1 cut time with respect to 1 beat of BPM
	time.
TIME (parameter 2)	Use this to set the effect time.
	10 to 16000 (ms)
LEVEL/DEPTH (param-	Sets the balance between the original sound and the effect
eter 3)	sound.
EFFECT FREQUENCY	This sets the amount of the original sound to be cut for the
(parameter 4)	different bands.

This function outputs the input sound that has a level above the threshold level, cutting the input sound that has a level below the threshold level.

The threshold level can be changed at [EFFECT FREQUENCY].

Beat buttons (parameter 1) This sets the release time between 1 and 100 %.

TIME (parameter 2)	This sets the release time.
	1 to 100 (%)
LEVEL/DEPTH (param-	Sets the threshold level.
	The further the control is turned clockwise, the more the effect
eter 3)
	is stressed and the sound is cut.
EFFECT FREQUENCY	Use these to set the threshold levels for the different bands.
(parameter 4)

SEND/RETURN1

SEND

RETURN

Effector

DJM-2000

Connect an external effector, etc., here.

[EFFECT FREQUENCY] can be used as an isolator.

Beat buttons (parameter 1) —

TIME (parameter 2)	—
LEVEL/DEPTH (param-	This adjusts the sound level input to the [RETURN] terminal.
eter 3)
EFFECT FREQUENCY	This sets the audio output level of the RETURN sound for the
(parameter 4)	different bands.

1When “A”, “B” or “M” is selected with the [CH SELECT] buttons, the effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT) unless the sound for the channel you want to monitor is being output from [MASTER] channel.

2When BEAT EFFECT is off, the effect sound cannot be monitored by pressing [CUE] (BEAT EFFECT).

PHASER1

Phase shift

Time

Cycle

The phaser effect changes according to the beat button fraction.

En 23