Manuals / Ricoh / Computer Equipment / Copier

Ricoh A251 manual SB011

Models: A251

1 151

Download 151 pages 25.34 Kb

1213

Specification ChangingThe Default Setting Function indicators Preset Cutting AccessTo Machine Adjusting Copy Image Density Copy Settings Weight How to Safety

Page 12

Notes

❐If you want to catch copies the back of the machine, change the copy delivery directions as shown in the figure.

SB011

3

Page 11 Page 13

Image 12

Ricoh A251 manual SB011

Page 11 Page 13

Related pages Troubleshooting for Samsung HT-D5200/XE Specifications for Targus PAUM30U / 400-0110-001C Fault Codes for Norcold 1200XX Boom Hose Schematic 17 FT Boom ARM for Alamo 02968915P How to measure range with the cursor for Furuno CH-250 Automatic installation for Philips FTR9964/69S Instructions Parts List for Graco 965129 If there are more than one code listed for your brand for JVC RX-8000VBK Table C-1 SO-DIMM0 connector 200-pin 1/3 for Toshiba S4 Troubleshooting and error code for Samsung MG23F301TCS/LI What are the power requirements for the Sanyo MBR-704GR refrigerator?

Contents

A251 Operating Instructions Safety Information Safety During OperationThis manual, the following important symbols are used IntroductionPage Iii Rcaution Page Page Table of Contents Whatyour Service Representative Getting Started Howto Usethis Copy Machine PB003 SB011 Where IT is & What IT is Copier ExteriorSet the Manual Pocket as shown in the figure 1a & 1b Locks Toner bottle and to remove jammed paperThat can’t be bent, use the Rear Table see Original Guides Function indicators Top indicator lights when the paper length is being setMiddle indicator lights when the lead margin is being set Operation Panel Set Paper or RF Select indicator Recommended Originals To the right or left of the center Non-recommended originals Thermosensitive paper, aluminium foil, etc Recommended Paper Dehumidifing Heater HandlingToner Toner StorageUsedToner Used toner cannot be re-used Copying Basic Copying Copyingto Sheets Pull down the Copy Paper Table Paper Length Film Copy Media Lighter Darker Page Using the RearTable Insert the original face down from the Rear Copying Onto Roll Paper Option Semi Synchro Cut SB015 Preset Cutting Continue from of P Variable Cutting Continue from on Usingthe Roll Cutting Rail Option Page Copy Settings Copying Onto Other Media Adjusting the Fusing Temperature Manually Vellum 1234 Film Adjusting Copy Image Density Press the Lighter or Darker key to adjust copy density Making Several Copies Ofthe Same Original Setting a Leading Edge Margin You can set a margin at the leading edge of the copy Partial Copying P will stay on, not blinking. The copier starts copying Programming Settingyou Often USE Program keyMake a copy, then press the Program key ChangingThe Default Setting Recalling Settings Stored In The Program key Usertools Whatyour Service Representative can Change Page Maintaining Your Copier Changingthetoner Bottle SM012 SB023 When Dis displayed, it is time to supply toner Addingtoner Open the toner cartridge cover Turn the old cartridge towards you Take the right edge of the seal and slowly remove it Loading a Roll of Paper Open the top and bottom covers of the Roll Feeder SM029 SM033 SM037 SM038 SM039 SM027 Loading a NEW Roll Onto Paper Cutting Rail Lower the rail If a Service Indicator Lights Up If Something GoesWrong If the original is jammed in the feed-in slot If the original is jammed at the exit If sheet paper is jammed in the feed-in slot Table and the Copy Paper Table Open the fusing unit cover If sheet paper is jammed at the paper exit If roll paper jams Open the roll feeder top cover SB056 SB023 Others Something happens, but Set Paper or RF Select never appear Check that the exposure glass is clean Creases Clean the exposure glass & the platen plate Thingsto do Every DAY DO’S & DON’TS Cord Whereto Putyour Copier Machine Environment Power connection Environments to avoid AccessTo Machine Specifications Copier Weight 33kg 73lb Options Index Page A252 Operating Instructions Introduction Page Iii Rcaution Page Page Setting the Number of Copies If a Service Indicator Lights Up Synchro First, the original is fed through to the Rear Table Copies are delivered at the rear of the machine Set the Manual Pocket as shown SM009 1a. & 1b. Locks Used toner bottle and to remove jammed paperOriginal into the copier Can’t be bent, use the Rear Table see Press the Function key to cycle through them Select indicators Tion is shown by the indicatorsSet Paper and RF Paper Recommended Originals SM066 Roil Feeder Dehumidifing Heater Toner Do not use the paper which is cut obliquely Pull down the Bypass Table Synchro SM004 Copy is delivered at the back of the copier Clear/Stop key and remove the original SM058 Choose any copy settings you require Synchro Cutting SM059 Continue from on page20 Copy Media Page Copy Settings Energy Set Saver Adjusting Copy Image Density Settingthe Number of Copies Repeated Copying Setting a LEADING/TRAILING Edge Margin Leading Edge Trailing Edge Copy Counter Synchro Cut Mode Original Bypass Table SM060 Press the Program key Input the settings you want to store Turn the main switch off Usertools Whatyour Service Representative can Change Page Page SM011 SM012 SM016 SM017 SM019 SM023 When is displayed, it is time to install a new roll of paper SM029 SM033 SM037 SM038 SM039 SM027 Troubleshooting If Jams Occur SM045 Table and the Bypass Table Open the fusing unit cover SM050 SM054 SM050 Others Creases SM040 DO’S & DON’TS Whereto Putyour Copier Power connection AccessTo Machine Original Reference Position Side Guides Copy Stacker Index

Top Page Image Contents