Manuals / Ricoh / Computer Equipment / Copier

Ricoh A251 manual A252 Operating Instructions

Models: A251

1 151

Download 151 pages 25.34 Kb

<>

Specifications ChangingThe Default Setting Function indicators Preset Cutting AccessTo Machine Adjusting Copy Image Density Copy Settings Weight How to Safety

Page 77

®

A252

Operating Instructions

Page 76 Page 78

Image 77

Ricoh A251 manual A252 Operating Instructions

Page 76 Page 78

Related pages Frequently asked questions for Miele G 2630 SCI Hardwired electrical connection for Miele G 5280

Contents

A251 Operating Instructions Safety During Operation Safety InformationThis manual, the following important symbols are used IntroductionPage Iii Rcaution Page Page Table of Contents Whatyour Service Representative Howto Usethis Copy Machine Getting StartedPB003 SB011 Set the Manual Pocket as shown in the figure Where IT is & What IT isCopier Exterior Toner bottle and to remove jammed paper 1a & 1b LocksThat can’t be bent, use the Rear Table see Original GuidesTop indicator lights when the paper length is being set Function indicatorsMiddle indicator lights when the lead margin is being set Operation PanelSet Paper or RF Select indicator To the right or left of the center Recommended OriginalsThermosensitive paper, aluminium foil, etc Non-recommended originalsRecommended Paper Dehumidifing Heater Toner Storage HandlingTonerUsedToner Used toner cannot be re-usedBasic Copying Copyingto Sheets CopyingPull down the Copy Paper Table Paper Length Film Copy Media Lighter Darker Page Insert the original face down from the Rear Using the RearTableCopying Onto Roll Paper Option Semi Synchro Cut SB015 Continue from of P Preset CuttingContinue from on Variable CuttingUsingthe Roll Cutting Rail Option Page Copying Onto Other Media Copy SettingsVellum 1234 Film Adjusting the Fusing Temperature ManuallyPress the Lighter or Darker key to adjust copy density Adjusting Copy Image DensityMaking Several Copies Ofthe Same Original You can set a margin at the leading edge of the copy Setting a Leading Edge MarginPartial Copying P will stay on, not blinking. The copier starts copying Make a copy, then press the Program key Programming Settingyou Often USEProgram key Recalling Settings Stored In The Program key ChangingThe Default SettingUsertools Whatyour Service Representative can Change Page Changingthetoner Bottle Maintaining Your CopierSM012 SB023 Addingtoner When Dis displayed, it is time to supply tonerTurn the old cartridge towards you Open the toner cartridge coverTake the right edge of the seal and slowly remove it Open the top and bottom covers of the Roll Feeder Loading a Roll of PaperSM029 SM033 SM037 SM038 SM039 SM027 Loading a NEW Roll Onto Paper Cutting Rail Lower the rail If Something GoesWrong If a Service Indicator Lights UpIf the original is jammed at the exit If the original is jammed in the feed-in slotIf sheet paper is jammed in the feed-in slot If sheet paper is jammed at the paper exit Table and the Copy Paper Table Open the fusing unit coverOpen the roll feeder top cover If roll paper jamsSB056 SB023 Something happens, but Set Paper or RF Select never appear OthersCreases Check that the exposure glass is cleanThingsto do Every DAY Clean the exposure glass & the platen plateCord DO’S & DON’TSMachine Environment Whereto Putyour CopierEnvironments to avoid Power connectionAccessTo Machine Copier SpecificationsOptions Weight 33kg 73lbIndex Page A252 Operating Instructions Introduction Page Iii Rcaution Page Page Setting the Number of Copies If a Service Indicator Lights Up Synchro First, the original is fed through to the Rear Table Set the Manual Pocket as shown Copies are delivered at the rear of the machineSM009 Used toner bottle and to remove jammed paper 1a. & 1b. LocksOriginal into the copier Can’t be bent, use the Rear Table seePress the Function key to cycle through them Tion is shown by the indicators Select indicatorsSet Paper and RF PaperRecommended Originals SM066 Roil Feeder Dehumidifing Heater Toner Do not use the paper which is cut obliquely Pull down the Bypass Table Synchro SM004 Copy is delivered at the back of the copier Clear/Stop key and remove the original SM058 Synchro Cutting Choose any copy settings you requireSM059 Continue from on page20 Copy Media Page Copy Settings Energy Set Saver Adjusting Copy Image Density Settingthe Number of Copies Repeated Copying Setting a LEADING/TRAILING Edge Margin Leading Edge Trailing Edge Copy Counter Synchro Cut Mode Original Bypass Table SM060 Press the Program key Input the settings you want to store Turn the main switch off Usertools Whatyour Service Representative can Change Page Page SM011 SM012 SM016 SM017 SM019 SM023 When is displayed, it is time to install a new roll of paper SM029 SM033 SM037 SM038 SM039 SM027 Troubleshooting If Jams Occur SM045 Table and the Bypass Table Open the fusing unit cover SM050 SM054 SM050 Others Creases SM040 DO’S & DON’TS Whereto Putyour Copier Power connection AccessTo Machine Original Reference Position Side Guides Copy Stacker Index