Connections to, CinemaWall, Connecting Source | Runco XP-65, XP-50

Installation

3.4	Proceed as follows to connect the CinemaWall to your video sources, external controller(s)
Connections to the	– if present – and AC power.
CinemaWall	When connecting your equipment:
	• Turn off all equipment before making any connections.
	• Use the correct signal cables (sold separately) for each source.
	• Ensure that the cables are securely connected. Tighten the thumbscrews on
	connectors that have them.
Connecting Source ➤	Connect your video sources to the CinemaWall as shown and described in the sections
Components to the	that follow.
CinemaWall	HDMI Connections: The CinemaWall has four (4) HDMI video inputs for connecting a

	BD/DVD player, DTV decoder or any other device with a DVI or HDMI output. Connect
	such devices as shown in Figure 3-2.
	Tip	Use the HDMI inputs whenever possible. This ensures the highest
		video quality because the signal is carried in the digital domain
		throughout the entire signal path, from source component output
		into the display.

SLOT1

SLOT2

RAUDIO L PR/CR/R PB/CB/B Y/G

COMPONENT/RGB IN

SLOT3PC

HDMI

HDMI

HDMI

HDMI

AV OUT

AV OUT

AV OUT

AV OUT

HDMI sources (BD, DVD, DTV Set-Top Box etc.)

Figure 3-2. HDMI Source Connections

16	CinemaWall XP-50/XP-65 Installation/Operation Manual

Image 30

Runco XP-65, XP-50 operation manual Connections to, CinemaWall, Connecting Source, Components to

Contents

XP-50 XP-65 Page RuncoCare Standard Two Year Limited Warranty RuncoCare Standard Features RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of Conformity FCC Part Page Table of Contents Appendix A. Default Settings Maintenance and TroubleshootingSpecifications Operation List of Figures List of Figures Xiv Introduction About This Manual Significance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunction Description, Features and Benefits Key Features and Benefits Optional Accessories XP-50 Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand Connectors XP-506 XP-65 Power Input CinemaWall Remote Control Surround button Controls and Functions Installation Remote ControlOther surfaces Quick Setup Installation specialistStep Procedure For Details, refer to Installation Considerations Ambient Light Ventilation Other Considerations CinemaWall Connecting SourceConnections to Components to RCA-BNC adapter plug Analog RGB Connections RS-232 Controller Connecting External Speakers OptionalConnector Pin Assignments Connection AC Power Connection Turning on the Power Changing the OSD Language Setting the Day and TimeOperation Setting the Computer Display Properties Selecting an Input Source Changing the Aspect Ratio Aspect ratio selection is saved independently for each input 169 149 Played at the left and right 43 431 linearly scalesSource image horizon Edges of the screen Using Picture-In-Picture PIP Activating PIP Swapping the Main PIP Images Screen or Input Source Using the On-Screen MenusSelecting a PIP Target Changing the PIP Window Position POS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness CinemaWall memorizes position and size settings separately POS./SIZE Options menu refer to page 50 is set to On Frequency is 108 MHz or greater Or 1080p and the Aspect Ratio is set to 169 refer to Sound SET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Refer to Changing the OSD Language on Order to activate multi-display mode, you must first set On hides joints between displays C D Transparency cannot be used when Insert is set to on Insert cannot be used when Transparency is set to on Command Timer refer to Present Time Setup Refer to Setting the Day and Time on DVD3 Operation Return Change Refer to Level see below Currently active MULTI-DISPLAY is active When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when Picture menu is set to Warm Using Digital Zoom During the delay period, the power indicator flashes greenOn page 21, the Clock Display setting has no effect Operation Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Cleaning the Screen Troubleshooting Tips Symptom Possible Causes Solution Serial Communications Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Examples Serial Commands Hex Description Dwaovlon OSPSCR0 Specifications CinemaWall Specifications CinemaWall Dimensions CinemaWall Model XP-50 Dimensions with Optional Table Stand CinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Appendix A. Default Settings Table A-1. Runco Factory Default Settings for CinemaWall Default Settings Page 020-0970-00 Rev. B March