Operation, Setting the Day and Time | Runco XP-50, XP-65 manual

4. Operation

1.Turn on your source components.

2.Press the main power switch on the CinemaWall (see Figure 2-1or Figure 2-2). The standby/on indicator lights green.

3.After a brief warm-up period (approximately five seconds), the CinemaWall will display an image.

4.Press the POWER button on the remote control to put the CinemaWall into standby

mode. The power indicator lights solid red.

5. Press the POWER button again to return to normal operation.

The CinemaWall OSD language is initially set to English, but can also display the menus in Russian, German, French, Italian or Spanish. To change the OSD language:

1.Press SET UP on the remote control unit.

2.Press repeatedly until OSD LANGUAGE is highlighted.

3.Press or to select the desired language. The change takes effect immediately.

4.1

Turning on the Power

4.2

Changing the OSD Language

You can program the CinemaWall to perform various actions, such as turning on or off, at specific times of the day and days of the week. In order to take advantage of this capability, the CinemaWall internal clock must be set correctly. To do this:

1.Press SET UP on the remote control unit.

2.Press or repeatedly until PRESENT TIME SETUP is highlighted.

3.Press the ACTION () button.

4.	Press	or	repeatedly to highlight DAY
4.	Press	or	repeatedly to highlight DAY		PRESENT TIME SETUP
	in the menu.					PRESENT TIME OF DAY MON 99:99
5.	Press	or	to select the current day of			PRESENT TIME OF DAY MON 99:99

					SET
	the week.				DAY				TUE
	the week.				PRESENT TIME OF DAY				10:00
					PRESENT TIME OF DAY				10:00
6.	Repeat Steps 4 and 5 to set the current							RETURN
	time of day.					SELECT		SET
	time of day.

7.Press or repeatedly to highlight SET

in the menu, then press the ACTION () button.

4.3

Setting the Day and Time

CinemaWall XP-50/XP-65 Installation/Operation Manual

21

Image 35

Runco XP-50, XP-65 operation manual Operation, Turning on the Power Changing the OSD Language, Setting the Day and Time

Contents

XP-50 XP-65 Page RuncoCare Standard Features RuncoCare Standard Two Year Limited Warranty RuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance Information FCC Part Page Table of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. Default Settings List of Figures List of Figures Xiv About This Manual Introduction Degrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental information Key Features and Benefits Description, Features and Benefits Optional Accessories XP-50 CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand XP-506 XP-65 Connectors Power Input Surround button CinemaWall Remote Control Controls and Functions Other surfaces InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation specialist Installation Considerations Ventilation Ambient Light Other Considerations Components to Connecting SourceConnections to CinemaWall RCA-BNC adapter plug Analog RGB Connections Connection Connecting External Speakers OptionalConnector Pin Assignments RS-232 Controller AC Power Connection Operation Turning on the Power Changing the OSD LanguageSetting the Day and Time Setting the Computer Display Properties Aspect ratio selection is saved independently for each input Selecting an Input Source Changing the Aspect Ratio 149 169 Edges of the screen 43 431 linearly scalesSource image horizon Played at the left and right Activating PIP Swapping the Main PIP Images Using Picture-In-Picture PIP Changing the PIP Window Position Using the On-Screen MenusSelecting a PIP Target Screen or Input Source POS./SIZE Options Picture This control is not available when Picture Menu is set to Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness POS./SIZE CinemaWall memorizes position and size settings separately Frequency is 108 MHz or greater Options menu refer to page 50 is set to On Sound Or 1080p and the Aspect Ratio is set to 169 refer to SET UP Signal Screensaver Is active On the remote control unit, or cycle power to the CinemaWall Order to activate multi-display mode, you must first set Refer to Changing the OSD Language on On hides joints between displays C D Insert cannot be used when Transparency is set to on Transparency cannot be used when Insert is set to on Present Time Setup Refer to Setting the Day and Time on Command Timer refer to DVD3 Operation Refer to Return Change Currently active Level see below Picture menu is set to Warm When using multiple displays such as in a video wall RuncoSome cases, power is transmitted to the slot when MULTI-DISPLAY is active On page 21, the Clock Display setting has no effect Using Digital ZoomDuring the delay period, the power indicator flashes green Operation Cleaning the Screen Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote Control Symptom Possible Causes Solution Troubleshooting Tips Examples Command 3 bytes Parameter 3 bytesCommand 3 bytes Parameter 6 bytes Serial Communications Hex Description Serial Commands Dwaovlon OSPSCR0 CinemaWall Specifications Specifications CinemaWall Model XP-50 Dimensions with Optional Table Stand CinemaWall Dimensions CinemaWall Model XP-65 Dimensions with Optional Table Stand Supported Timings Supported Signal Timings by Input Specifications Table A-1. Runco Factory Default Settings for CinemaWall Appendix A. Default Settings Default Settings Page 020-0970-00 Rev. B March