Samsung SMT-190Dx user manual Network Setup, Language, Dhcp

USER'S MANUAL

On the contrary, in 8 Channel mode, the data recorded in Channel 1 mode will not playback and only the data recorded in 8 Channel can be played. If you want to switch from 1 channel mode back to 8 channel mode, set 1CH RECORD SUPPORT to OFF and exit the MENU. Then, you will see a message, "SYSTEM CHANGE 8CH DVR?" asking if you want to switch the system mode. If you click OK, the system will be switched.

[ON/OFF]

8.LANGUAGE

Many language are provided and select a your language. English is the default.

[ENGLISH/FRANÇAIS/DEUTSCH/ESPAÑOL/

ITALIANO/PYCCKИЙ/SVENSKA/PORTUGUÊS/

/POLSKI/ČESKY/ /TÜRKÇE/DUTCH/

DANSK/HRVATSKI]

5-9) NETWORK SETUP

This section of the manual is intended for users who will install this security system in a network environment.

If you have difficulty setting the network,we recommend contacting your network administrator.

•Static

•DHCP

•PPPoE(ex. ADSL)

•Function: Allow users to select the STATIC

(fixed) IP, DHCP, PPPoE of Setting.

•Setting method: Move to, NETWORK SETUP MENU by using /KEY in the SETUP MENU, then press the ENTER SWITCH to display the OSD as shown in the figure below. (The figure shows the initial setting status)

	07/07/07	00:00:01
NETWORK SETTING
1. NETWORK ACCESS	STATIC...
2. HTTP PORT	00080
3. PICTURE QUALITY	NORMAL
NETWORK STATUS
IP ADDR	192.168.1.2
GATEWAY	192.168.1.65
SUBNETMASK	255.255.255.0
DNS 1	168.126.63.1
DNS 2	168.126.63.2
MAC ADDR	00:30:6f:ff:00:00

DDNS ADDR wff0000.websamsung.net

MOVE TO EACH item by using / KEY, and using / KEY to change the set value.

Static IP User

-Constituted by Static IP on the TCP/IP network 1) Move to ‘STATIC...’ by using / KEY at NETWORK

ACCESS, then press ENTER SWITCH to set

STATIC...

(STATIC : Select in case the network configuration of monitor is fixed IP (Public or Private IP)

	07/07/07	00:00:01
STATIC ACCESS
IP ADDR	192.168.1.2
GATEWAY	192.168.1.65
SUBNETMASK	255.255.255.0
DNS 1	168.126.63.1
DNS 2	168.126.63.2

2)Move to IP ADDR / GATEWAY / SUBNETMASK by using / KEY .

3)Press ENTER SWITCH and type in IP ADDR / GATEWAY / SUBNETMASK respectively.

4)DNS 1 and DNS 2 will be automatically set to DNS as shown above. Use / KEY to change it.

DHCP User

-Constituted by Dynamic IP on the cable/xDSL modem network

You can use the SMT-190DN products through the network using Dynamic IP on cable/xDSL modem. In this case, it should be connected with DDNS to support the Dynamic IP. In case of a configuration using DHCP, as the connection to SMT-190DN is made using domain names (EX : http://wff0000.websamsung.net) that are automatically registered in our DDNS server,

IP address, Subnet Mask and Gateway that are in the network tab of Admin Mode are not to be changed. The proper domain names of SMT-190DN are automatically registered to DDNS server installed in our company in case of modem connection.

The default IP type is DHCP .

1)Connect as the figure below and turn on the power of the equipment in the order shown.

  

2)After setting, move to the main screen by using the MENU button.

3)Set values will be stored shown below. It takes 30 to 35 seconds.

Eng-24