CHECKING THE SIZE OF A PLACED ORIGINAL

If the placed original is a standard size, the size will be automatically detected (automatic original detection function) and displayed in the touch panel. Make sure that the correct size has been detected.

(A):The original size is displayed.

(B):[AUTO] appears when the automatic original detection function is operating.

If you have loaded a non-standard size original or wish to change the scanning size, you can follow the steps below to manually set the original scanning size. (For the standard sizes, see "Original size detection function" on page 4-3.)

0

81/2x11 AUTO ORIGINAL

AUTO

EXPOSURE

(A)(B)

NOTE

If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed, or the original size may not appear at all.

If "CANCEL DETECTION AT DOCUMENT GLASS" is enabled in the key operator programs (see page 11 of the key operator’s guide), automatic original detection at the document glass will not operate. In this case, follow the steps below to manually set the original scanning size.

Manually setting the scanning size

4

If you load an original that is not a standard size (such as an AB size), or if the size is not detected correctly, you must

 

touch the [ORIGINAL] key and set the original size manually. Perform the following steps after placing the document

 

in the automatic document feeder or on the document glass.

 

1Touch the [ORIGINAL] key.

AUTO

If a non-standard size original is placed in the document feeder or on the document glass, touch the [SIZE INPUT] tab and then enter the X (width) and Y (length) dimensions of the original.

ORIGINAL

AUTO

EXPOSURE

2Touch the desired original size key.

 

X

 

 

 

 

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Y

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X

 

 

17

 

(2 1/2 17)

 

 

 

 

 

 

 

 

inch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Y

 

 

11 5/8

 

(2 1/2 11 5/8)

 

 

 

 

 

 

 

inch

 

 

 

 

 

 

 

 

 

 

STANDARD SIZE

 

SIZE INPUT

X is initially selected. Enter the X dimension (width) and then touch the Y( ) key and enter the Y dimension (length). X can be from 2-1/2 to 17 inch, and Y can be from 2-1/2 to 11-5/8 inch.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[AUTO]

is

no

longer

 

 

 

 

 

 

 

 

 

 

 

 

OK

 

 

 

 

51/2X81/2

 

 

 

81/2X13

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

highlighted.

[MANUAL]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

51/2X81/2R

 

 

 

81/2X14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AB

and the original size key

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

81/2X11

 

 

 

11X17

 

 

 

 

 

 

 

 

you

touched

are

 

 

 

 

 

INCH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

81/2X11R

 

 

 

 

 

 

 

 

 

 

 

 

 

highlighted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDARD SIZE

 

 

SIZE INPUT

 

 

 

 

If you frequently use originals that are the same non-standard size, you can store the size as explained in "STORING, DELETING, AND USING ORIGINAL SIZES" on the following page. This will save you the trouble of manually entering the size each time you use that original size.

If you wish to select an AB size, touch the [AB/INCH] key and then touch the desired original size key.

 

 

A5

 

A4

 

 

 

OK

 

[AB]

is highlighted and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AB

size keys

are

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A5R

 

A4R

 

 

 

 

 

 

 

 

 

 

 

 

 

AB

 

 

 

 

 

 

 

 

 

displayed. To return to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B5

 

 

 

B4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INCH

 

the

inch palette,

touch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B5R

 

 

A3

 

 

 

 

 

 

 

 

the [AB/INCH] key once

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

again.

 

 

 

STANDARD SIZE

 

 

 

 

 

 

 

 

 

 

 

 

 

SIZE INPUT

 

3Touch the [OK] key.

You will return to the initial screen.

4The selected original size appears in the top half of the [ORIGINAL] key.

A4

ORIGINAL

AUTO

EXPOSURE

4-5