Manuals
/
Brands
/
Communications
/
Telephone
/
SpectraLink
/
Communications
/
Telephone
SpectraLink
150 M3 MCU
- page 26
1
26
63
63
Download
63 pages, 334.93 Kb
SpectraLink Corporation
Link WTS Installation and Operation
Part Number:
72
-
0075
-
01
-
C
-
W.doc
Page
15
Two Wire Analog or Digital Demarc Block
The demarc block for the two
-
wire analog or digital interface should be wired as follows.
Contents
Main
NOTICE
Trademark Information
Note concerning the Master Control Unit:
Note concerning shielded cable:
Note concerning the Wireless Telephone and Base Stations:
UL Information
FCC Information
Industry Canada (IC) Notice
Notice:
Warranty and Repair Service Center:
DOC Spread Spectrum certification
Warranty Support Program
World-class support for your Wireless Telephone System
Page
Cleaning Tips for Wireless Telephones
Table of Contents
Page
1. About This Document
1.1 Questions?
1.2 Icons and Conventions
!! Note these instructio ns carefully.
1.3 Installation Overview
This table lists the installation steps and the person usually responsible for each step.
2. Link Wireless Telephone System Overview
2.1 System Operation
Page
2.2 The Front Panel of the Link 150 M3 MCU
3. Site Preparation
!! If your system has more than one MCU, the units should be mounted
3.1 Required Materials
3.2 Determine Location of MCU
4. Run Cable for System
!! The customer's wire contractor is responsible for adhering to all local codes
4.1 Run Cables to Base Station Locations
!! The wire length between the MCU and each Base Station may not exceed
Wire Specifications
!! One additional pair is required for Data.
!! Remove bridge taps, multiples, or "Y" connections to the Base Station wires;
4.3 Terminate Cable at Base Station Locations
!! To avoid damage to the connectors or crimps, be sure to run the wire to the
4.4 Prepare Demarc Blocks
Page
Page
Page
4.5 Install Demarc Blocks
4.6 Assign and Program Ports
4.7 Connect Cables from Base Stations and Phone Lines to Demarc Blocks
!! Up to four Base Stations can be connected on a single MCU. Each Base
Page
Page
Page
5. Install Link Wireless Telephone System
!! The Link Wireless Telephone System MUST contain only Link 150
5.1 Survey Site
5.2 Check Components
5.3 Install MCUs
Mount MCUs to Wall
Connect MCU to Demarc Blocks
Connect Multi-Unit Systems
!! No IPC cable is connected to the IN Port of the first unit. An Open
Connect Power
!! For installations with more than one MCU, use an outlet strip with a built
Set Switch Interface Type
Page
5.4 Install Base Stations
Mount Base Stations on Dropped Tile Ceilings
Mount Base Stations On Finished Ceilings
!! The customer's wire contractor is responsible for this installation.
5.5 Install Outdoor Base Stations
!! Only RCO Base Stations can be used outdoors.
Wire and Connect Outdoor Base Stations
6. Connect and Register Wireless Telephones
!! This internal modem uses proprietary communication software. You cannot
6.1 Set Up Diagnostic Modem
!! Line 1 MCU 1 should be skipped to allow for remote access through the
6.2 Register Wireless Telephones
6.3 Unregister Wireless Telephones
6.4 Program Wireless Telephone Features
6.5 Test Wireless Telephones
7. Site Certification
8. System Administration
!! Certain four-wire telephones (such as MERLIN LEGEND) use a different
8.1 Troubleshoot Error Codes
8.2 Troubleshoot Phone Features
8.3 Status LED Codes
The following STATUS LEDs are displayed in combination with the ERROR LED.
Page
Page
Wireless Telephone Status Indicator Messages
8.4 Replace a Wireless Telephone
Delete Old Wireless Telephone
Register New Wireless Telephone
8.5 Replace an MCU
Clear Configuration on Replacement MCU
Connect the Replacement MCU
8.6 Replace a Base Station
9. Wireless Telephone Planning Worksheet
!! *On MCU No. 1: Reserve Port 1 for access to SpectraLink Diagnostic
10. Base Station Location Worksheet
11. Appendix A: Technical Parameters
11.1 Select Alternate Spread Spectrum Sequence
11.2 Change Companding
12. Appendix B: Program Analog Features
12.1 Defining Macros
!! Do not program analog features on a digital system.
Open Application Interface
12.2 Plan Programming
12.3 Program Macro Codes
!! In multi-unit installations, be sure all MCUs are properly connected to one
12.4 Examples of Programming
Transfer:
Speed Dial:
Clear or Erase A Function:
13. Appendix C: Installing the Open Applications Interface (OAI) Telephony Gateway
13.1 Before Installing the OAI Telephony Gateway
13.2 The OAI Telephony Gateways Front Panel
13.3 Mount Telephony Gateway to Wall
13.4 Initial Test
13.5 Connect the OAI Telephony Gateway to the MCU
!! Do NOT stack the MCUs and OAI Telephony Gateway on top of each
13.6 Connect the OAI Telephony Gateway to the Application Server
13.7 Assign A Function Key to OAI Telephony Gateway
13.8 Certification Test
SpectraLink Corporation Link WTS Installation and Operation
Part Number: 72-0075-01-C-W.doc Page 51
Index
SpectraLink Corporation Link WTS Installation and Operation
Part Number: 72-0075-01-C-W.doc Page 52