Manuals / Brands / Communications / Telephone / SpectraLink / Communications / Telephone

SpectraLink 150 M3 MCU SpectraLink Corporation Link WTS Installation and Operation , Part Number: 72-0075-01-C-W.doc Page 52

1 63

Download 63 pages, 334.93 Kb

SpectraLink Corporation Link WTS Installation and Operation Part Number: 72-0075-01-C-W.doc Page 52

Mounting, 19

Multiple, 20

Replacing, 36

Mode Switch, 5

Modem, 10, 26

Mounting Hardware, 18

Mu-law, 41

OAI

Assigning Function Key, 49

Certification Test, 50

Connecting to MCU, 48

FCN key, 42

Gateway Connection Diagram, 48

Gateway front panel, 46

Mounting the Telephony Gateway, 46

Open Applications Interface. See OAI

PBX type, 21

Power

AC Adapter. See

Outlet strip, 6

Power jack, 5

Programming, 13

Quick Clip Fuse, 6

Remote Access via modem, 10

Replacing

Base Station, 37

MCU, 36

Wireless Telephone, 35

Site Certification, 29

Site Preparation, 6

Site Survey, 18

Spread Spectrum Sequence, 40

STEP Button, 5

Switch programming, Analog, 42

Switch type, 21

Ports, 10

Troubleshooting, 30

Unregister Wireless Telephone, 27

Walk test, 29

Wireless Telephone

Description, 4

Planning Worksheet, 38

Program, 28

Replacing, 35

Test, 28

Unregister, 27

Contents

Main NOTICE Trademark Information Note concerning the Master Control Unit: Note concerning shielded cable: Note concerning the Wireless Telephone and Base Stations: UL Information FCC Information Industry Canada (IC) Notice Notice: Warranty and Repair Service Center: DOC Spread Spectrum certification Warranty Support Program World-class support for your Wireless Telephone System Page Cleaning Tips for Wireless Telephones Table of Contents Page 1. About This Document 1.1 Questions? 1.2 Icons and Conventions !! Note these instructio ns carefully. 1.3 Installation Overview This table lists the installation steps and the person usually responsible for each step. 2. Link Wireless Telephone System Overview 2.1 System Operation Page 2.2 The Front Panel of the Link 150 M3 MCU 3. Site Preparation !! If your system has more than one MCU, the units should be mounted 3.1 Required Materials 3.2 Determine Location of MCU 4. Run Cable for System !! The customer's wire contractor is responsible for adhering to all local codes 4.1 Run Cables to Base Station Locations !! The wire length between the MCU and each Base Station may not exceed Wire Specifications !! One additional pair is required for Data. !! Remove bridge taps, multiples, or "Y" connections to the Base Station wires; 4.3 Terminate Cable at Base Station Locations !! To avoid damage to the connectors or crimps, be sure to run the wire to the 4.4 Prepare Demarc Blocks Page Page Page 4.5 Install Demarc Blocks 4.6 Assign and Program Ports 4.7 Connect Cables from Base Stations and Phone Lines to Demarc Blocks !! Up to four Base Stations can be connected on a single MCU. Each Base Page Page Page 5. Install Link Wireless Telephone System !! The Link Wireless Telephone System MUST contain only Link 150 5.1 Survey Site 5.2 Check Components 5.3 Install MCUs Mount MCUs to Wall Connect MCU to Demarc Blocks Connect Multi-Unit Systems !! No IPC cable is connected to the IN Port of the first unit. An Open Connect Power !! For installations with more than one MCU, use an outlet strip with a built Set Switch Interface Type Page 5.4 Install Base Stations Mount Base Stations on Dropped Tile Ceilings Mount Base Stations On Finished Ceilings !! The customer's wire contractor is responsible for this installation. 5.5 Install Outdoor Base Stations !! Only RCO Base Stations can be used outdoors. Wire and Connect Outdoor Base Stations 6. Connect and Register Wireless Telephones !! This internal modem uses proprietary communication software. You cannot 6.1 Set Up Diagnostic Modem !! Line 1 MCU 1 should be skipped to allow for remote access through the 6.2 Register Wireless Telephones 6.3 Unregister Wireless Telephones 6.4 Program Wireless Telephone Features 6.5 Test Wireless Telephones 7. Site Certification 8. System Administration !! Certain four-wire telephones (such as MERLIN LEGEND) use a different 8.1 Troubleshoot Error Codes 8.2 Troubleshoot Phone Features 8.3 Status LED Codes The following STATUS LEDs are displayed in combination with the ERROR LED. Page Page Wireless Telephone Status Indicator Messages 8.4 Replace a Wireless Telephone Delete Old Wireless Telephone Register New Wireless Telephone 8.5 Replace an MCU Clear Configuration on Replacement MCU Connect the Replacement MCU 8.6 Replace a Base Station 9. Wireless Telephone Planning Worksheet !! *On MCU No. 1: Reserve Port 1 for access to SpectraLink Diagnostic 10. Base Station Location Worksheet 11. Appendix A: Technical Parameters 11.1 Select Alternate Spread Spectrum Sequence 11.2 Change Companding 12. Appendix B: Program Analog Features 12.1 Defining Macros !! Do not program analog features on a digital system. Open Application Interface 12.2 Plan Programming 12.3 Program Macro Codes !! In multi-unit installations, be sure all MCUs are properly connected to one 12.4 Examples of Programming Transfer: Speed Dial: Clear or Erase A Function: 13. Appendix C: Installing the Open Applications Interface (OAI) Telephony Gateway 13.1 Before Installing the OAI Telephony Gateway 13.2 The OAI Telephony Gateways Front Panel 13.3 Mount Telephony Gateway to Wall 13.4 Initial Test 13.5 Connect the OAI Telephony Gateway to the MCU !! Do NOT stack the MCUs and OAI Telephony Gateway on top of each 13.6 Connect the OAI Telephony Gateway to the Application Server 13.7 Assign A Function Key to OAI Telephony Gateway 13.8 Certification Test SpectraLink Corporation Link WTS Installation and Operation Part Number: 72-0075-01-C-W.doc Page 51 Index SpectraLink Corporation Link WTS Installation and Operation Part Number: 72-0075-01-C-W.doc Page 52