Sun Microsystems CP3220

Chapter 1 Introduction 1-9

Note – Use only serial cables that are less than 10 meters in length.

FIGURE1-6 shows the physical relationship between the Sun Netra CP3220 blade

server,the ARTM, and the backplane in a typical ATCA system.

FigureLegend

1 Serial port

2 10/100/1000 MBASE-T management port

3 External SAS port (secondary)

4 External SAS port (primary)

5 Harddisk drives

6 RTMAlignment pin

7 Zone 3 connectors

8 OK LED

9 Out-of-service (OOS) LED

10 BlueHot Swap LED

Contents

Main Please Recycle Contents Page Page Page Page Page Figures Page Page Page Tables Page Preface How This Document Is Organized Using UNIX Commands Shell Prompts Typographic Conventions Related Documentation Page Introduction 1.1 Overview 1.2 Features 1.3 Physical Description 1.3.1 Front Panel Components Page Page Page 1.4 System Configurations 1.4.1 AMC Modules 1.4.2 Advanced Rear Transition Module Page Note Caution Page 1.5 Hot-Swap Support 1.6 System Components 1.6.1 Required Hardware Components Caution Note 1.6.2 Optional Hardware Components 1.6.3 Software Components 1.7 Technical Support and Warranty 1.7.1 Locating the Blade Server Identification Information Page Page Hardware Installation and Service 2.1 Safety and Tool Requirements 2.1.1 Equipment and Operator Safety Caution 2.1.2 Materials and Tools Required 2.2 Installing the Blade Server 2.2.1 Preparing for the Installation 2.2.1.1 Check Power, Thermal, Environmental, and Space Requirements 2.2.1.2 Local Network IP Addresses and Host Names Worksheet 2.2.1.3 Installation Procedure Summary 2.2.2 Configuring the Hardware 2.2.2.1 Verify Chassis Fan Tray Upgrade Caution 2.2.2.2 Installing Optional Components 2.2.2.3 Configuring the Advanced Rear TransitionModule Hardware 2.2.3 Installing the Sun Netra CP3220 Blade Server in an ATCA Shelf Note 2.2.3.1 Installing an Advanced Rear Transition Module Page To Install an ARTM Note Page 2.2.3.2 Installing the Blade Server Into the Shelf Note 2.2.4 Connecting External I/O Cables Rear TransitionModule, Dual HD Users Guide (820-0460) for more information. Note Note 2.2.4.1 Connecting Cables to a System Console Running the Solaris OS Page 2.2.4.2 Connecting Cables to the System Console Not Running the Solaris OS 2.2.4.3 Netinstall Boot Device Map Page 2.3 Service Procedures 2.3.1 Hot-Swapping the Sun Netra CP3220 Blade Server 2.3.2 Powering Off the Sun Netra CP3220 Blade Server 2.3.3 Removing the Sun Netra CP3220 Blade Server 2.3.4 Powering On the System 2.3.5 Automatic Power-Off Events 2.3.6 Servicing DIMMs 2.3.6.1 DIMM Requirements Page 2.3.6.2 Installing a DDR2 DIMM Caution 2.3.6.3 Removing a DDR2 DIMM Note Caution Note 2.3.7 Installing the Optional Compact Flash Card Caution Page 2.3.8 Installing Optional AMC Cards Note Page Caution 2.3.9 Adding or Replacing a TOD Clock Battery Caution 2.3.10 Changing Jumper Settings 2.3.10.1 Clearingthe CMOS Setting Using Jumper 1 Page Note 2.3.10.2 Changing the OOS LED Color 2.3.11 Changing OOS LED Behavior Page Viewing OOS LED Settings Setting OOS LED Behavior Note 2.3.12 Resetting the Sun Netra CP3220 Blade Server Caution Software Configuration 3.1 Operating Systems 3.2 Software Updates 3.3 SunVTS Software Note 3.4 Configuring Sun Netra CP3220 For 1GbE or 10GbE Switches 3.5 Configuring Alternate OOS LED Behavior Displaying Configuration of OOS LED Behavior Use the following command to display the current configuration of OOS LED behavior. Setting Configuration of OOS LED Behavior Use the following command to set the configuration of OOS LED behavior. the command with completion code 0xCC. Note Page Configuring and Using BIOS Firmware 4.1 About BIOS Settings 4.1.1 Navigating BIOS Screens 4.1.2 BIOS Considerations 4.1.2.1 BIOS Option ROMs on the Sun Netra CP3220 Blade Server 4.1.2.2 AMD PowerNow! Feature Enabled by Default 4.1.3 Description of the BIOS Screens 4.2 Changing the Configuration of a BIOS Menu Item Note 4.3 Setting the Boot Device Using BIOS Setup Screens Note Page Page Page 4.4 Changing the BIOS Continuous Boot Setting 4.5 Setting Supervisor and User Passwords Page 4.6 Resetting the System Time and System Date 4.7 Updating the BIOS 4.8 Secondary BIOS Image 4.9 Use the Secondary BIOS Image Note 4.10 Perform a Live Firmware Upgrade 4.11 Power-On Self-Test 4.12 Changing POST Options Page Page Hardware Architecture Page 5.2 The AMD Opteron Processor 5.3 Memory 5.4 Networking and I/O 5.4.1 nVidia MCP55 5.4.2 PCI Express Bus 5.4.3 Dual BIOS 5.4.4 Trusted Platform Module (TPM) 5.4.5 Broadcom 5715C Gigabit Ethernet 5.5 I/O Components 5.5.1 AMC Slots 5.5.2 EIDE/ATA for Compact Flash 5.5.3 SAS/SATA Physical Characteristics A.1 Form Factor A.2 Power and Thermal Metrics A.2.1 Processor Metrics A.2.2 PICMG Board Cooling Requirements triggered at any of the listed temperatures for the given airflow. A.2.3 PICMG ARTM Cooling Requirements A.3 Connectors and Pinouts A.3.1 Front Panel Connectors A.3.1.1 Ethernet Port 1 2 3 4 5 6 7 8 A.3.1.2 USB Ports ports. A.3.1.3 Serial Port 1 2 3 4 5 6 7 8 A.3.2 AMC Connectors A.3.3 Power Connector (Zone 1) The analog test and ring voltage pins areleft unconnected. FIGUREA-4 showsthe pin assignments. Page A.3.4 Data Transport Connector (Zone 2) A.3.5 Advanced Rear Transition Module Connector (Zone 3) J31 J32 J33 Page infrastructure signals. signals. BIOS Screens Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Index A B C D E F H I S U W