Discard Changes, Save Changes | SUPER MICRO Computer 6014P-82R

SUPERSERVER 6014P-8/6014P-8R/6014P-82R/6014P-82 User's Manual

Discard Changes

Highlight this item and hit <Enter> to discard (cancel) any changes you made. You will remain in the Setup utility.

Save Changes

Highlight this item and hit <Enter> to save any changes you made. You will remain in the Setup utility.

7-22

Image 96

SUPER MICRO Computer 6014P-82R, 6014P-8R user manual Discard Changes, Save Changes

Contents

Super Page Preface About This ManualManual Organization System Safety Advanced Serverboard SetupAdvanced Chassis Setup Bios Preface Table of Contents Advanced Serverboard Setup HDD LED NIC1/NIC2 LED Advanced Chassis Setup Bios Appendices Page Chapter Introduction Overview Serverboard Features Processors MemoryOnboard Scsi Onboard Controllers/Ports Server Chassis Features Other FeaturesSystem Power ATI Graphics Controller PCI Expansion Slots Front Control PanelBackplane Cooling System Intel E7520 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-Pacific Chapter Server Installation Preparing for SetupUnpacking the System Choosing a Setup Location Rack PrecautionsServer Precautions Rack Mounting Considerations Installing the System into a Rack Identifying the Rack SectionsChassis Rails Installing the Rack Rails Locking Tabs Installing the Server into the Rack Installing the Server into a Rack Installing the Server into a Telco Rack Installing the Server into a Telco Rack Checking the Serverboard Setup Accessing the Inside of the System Checking the Drive Bay Setup Chapter System Interface Control Panel Buttons Control Panel LEDs Scsi Drive Carrier LEDs Page Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup PrecautionsHandling the Serverboard Unpacking Processor and Heatsink Installation CPU Installation Heatsink Installation Pin PGA Socket Empty and with Processor Installed Installing the Heatsink Removing the Heatsink/CPU Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control Panel JF1 Header Pins Installing Memory Dimm Installation Figures 5-5a and 5-5bI/O Ports Memory Support Side View of Dimm Installation into Slot Memory Speed Jumpers X6DHP-8G only PCI card installation Adding PCI CardsPCI slots 6014P-8/6014P-82 Risers Slot Add-on Card Serverboard Details Super X6DHP-8G Layout Jumper Description Default Setting Connector DescriptionX6DHP-8G Quick Reference X6DHP-8G2 X6DHP-8G2 Quick Reference JWOR1 Connector Definitions ATX Power ConnectorProcessor Power Connector NMI Button Power & PWR Fail LED NIC1/2 LEDsOverheat/Fan Fail LED Power Button UID Button & UID LEDChassis Intrusion GLAN1/2 Ethernet Ports Universal Serial Bus USB0/1 Front Panel Universal Serial Bus HeadersFan Headers Serial Ports Power LED/Speaker Wake-On-RingATX PS/2 Keyboard and PS/2 Mouse Ports SMB Power Connector SMB Jumper Settings Glan Enable/DisableExplanation Jumpers Cmos Clear VGA Enable/Disable Scsi Controller Enable/ DisableScsi Termination Enable/ Disable DOC IDE Slot Bus Select JP17/JP18 Watch Dog Memory Speed Select X6DHP-8G only Onboard Indicators Glan LEDsScsi LEDs DA1/DA2 Unit Identifier Floppy Connector IDE ConnectorsFloppy/Hard Disk and Scsi Drive Connections Ultra320 Scsi Connectors Ultra320 Scsi Connector Pin Definitions JA1, JA2Page Chapter Advanced Chassis Setup Static-Sensitive DevicesTools Required Control Panel 6014P-8/6014P-826014P-8R/6014P-82R Installing a new fan System FansSystem Fan Failure Replacing System Cooling Fans Drive Bay Installation/Removal Accessing the Drive Bays Scsi Drive Installation Mounting a Scsi drive in a drive carrier Installing/removing hot-swap Scsi drive carrier DVD-ROM and Floppy Drive Installation Power Supply Power Supply FailureRemoving/Replacing the Power Supply 6014P-8R/6014P-82R 6014P-8/6014P-82 Reconfiguring the Power Supply Reconfiguring the 6014P-8/6014P-82 see Figure Reconfiguring the 6014P-8R/6014P-82R see Figure Page Reconfiguring the Power Supply Page Starting the Setup Utility ChapterIntroduction Running Setup Main Bios SetupPress the Delete key to enter Setup Main Bios Setup Menu Main Setup Features Bios DateSystem Time System Date Serial ATA RAID Enable Native Mode OperationLegacy Diskette a Parallel ATA Type LBA Mode Control Transfer ModeUltra DMA Mode Multi-Sector Transfer Advanced Setup Boot FeaturesQuick Boot Mode Quiet Boot Acpi Mode Power Button BehaviorAfter Power Failure Memory Cache Cache System Bios Area Cache Base 0-512K Cache Base 512K-640KCache Extended Memory PCI Configuration Onboard Glan Gigabit- LAN Oprom ConfigureReset Configuration Data Frequency for PCIX#1/SCSI Enable Master Latency TimerLarge Disk Access Mode Force Compliance Mode Dram Data Integrity Mode ECC Error TypeSerr Signal Condition USB Device Device Configuration Adjacent Cache Line PrefetchKBC Clock input Onboard COM1 Floppy Disk Controller DMI Event LoggingEvent Log Validity Event Log Capacity Console Redirection COM Port AddressBaud Rate Console Type Hardware Monitor Logic CPU Temperature Threshold P3V3 P1V8 P2V5N12VScaled Supervisor Password Is User Password IsSecurity Set Supervisor Password Set User PasswordFixed Disk Boot Sector Password on Boot Boot +Removable DevicesCD-ROM Drive +Hard Drive Load Setup Defaults ExitExit Saving Changes Exit Discarding Changes Discard Changes Save Changes Appendix a Bios Post Codes Recoverable Post ErrorsTerminal Post Errors Post Code Description Post Code Description Post Code Description Post Code Description Following are for boot block in Flash ROM Page Appendix B Software Installation Configuring Bios settings for the Sata RAID FunctionsAdaptec Embedded Sata RAID Controller Driver Serial ATA Sata Adaptec Embedded Sata with HostRAID Controller Driver Using the Adaptec RAID Configuration Utility ARC Using the Array Configuration Utility ACU Managing Arrays From the ARC menu, select Array Configuration Utility ACU Viewing Array PropertiesDeleting Arrays Creating Arrays To create an array Assigning Array Properties To assign properties to the new array When finished, press Done as shown on the following screen Page Adding a Bootable Array Deleting a Bootable Array Adding/Deleting Hotspares Initializing Disk Drives To initialize drivesPage Rebuilding Arrays To Rebuild an array Using the Disk Utilities To access the disk utilitiesYou can choose from the following options To Exit Adaptec RAID Configuration Utility Installing Intels ICH5R Driver by Adaptec and Windows OS Installing Other Software Programs and Drivers Installing Other DriversEach item, you must re-boot the system before moving on to Supero Doctor Figure B-2. Supero Doctor III Health Information Display Figure B-3. Supero Doctor III Remote Control Display Appendix C System Specifications Weight Expansion SlotsServerboard 6014P-8/6014P-8R Serverboard 6014P-82/6014P-82R PFC Power Supply ratings apply to each module Operating EnvironmentRegulatory Compliance