SUPER MICRO Computer X6QT8, X6QTE+ instruction

Appendix C: Software Installation

5.Repeat Step 4 so that both drives to be initialized are selected (as shown in the screen below).

6.Press Enter.

7.Read the warning message as shown in the screen.

8.Make sure that you have selected the correct disk drives to initialize. If cor- rect, type Y to continue.

C-13

Image 101

SUPER MICRO Computer X6QT8, X6QTE+ user manual

Contents

Super Page Conventions Used in this Manual About This Manual Table of Contents Table of Contents Appendices TroubleshootingBios Overview Checklist Headquarters Contacting SupermicroEurope Asia-Paciﬁc X6QT8 Image Important Notes to the User Super X6QT8 Description Jumper Description Default SettingQuick Reference X6QT8 LED Indicator Description Super Quick Reference X6QTE+ Memory Motherboard FeaturesChipset Expansion Slots *See Note 3 on LED Indicators Acpi Power FeaturesDimensions Software Block Diagram of the E8501 Chipset E8501 Chipset Chipset OverviewIndependent Memory Interface Interfaces PC Health Monitoring Special Features Auto-Switching Voltage Regulator for the CPU Core Acpi FeaturesSlow Blinking LED for Suspend-State Indicator Thermal Management/CPU VRM Overheat Main Switch Override Mechanism Power SupplyExternal Modem Ring-On WOR Wake-On-LAN WOL Super I/O Unpacking PrecautionsStatic-Sensitive Devices CPU Installation Processor and Heatsink Installation Heatsink Installation To Un-install the Heatsink Mounting the Motherboard in the Chassis Processor installedEmpty socket Memory Support Installing DIMMsDimm Installation See Figure Back Panel Connectors/IO Ports Control Panel Connectors/IO Ports Front Control Panel JF1 Header Pins Front Control Panel Pin Deﬁnitions NMI Button Power LED HDD LED NIC1/NIC2 LED Indicators OH/Fan Fail LED PWR Fail LED Power Fail LEDOverheat/Fan Fail LED Reset PWR Button Reset ButtonPower Button ATX Power Connector Connecting CablesSecondary Power Connectors Pin PWR Universal Serial Bus USB Chassis Intrusion Wake-On-Ring Wake-On-LAN Glan Giga-bit Ethernet Ports Serial Ports Fan Headers ATX PS/2 Keyboard and PS/2 Mouse Ports PWR Supply Fail VGA ConnectorPower Supply Failure SMB Header ConnectorSMB Power I2 C Compact Flash Card PWR Connectors JWF1, JWF2 Power LED/Speaker JD1 Alarm Reset JAR1 Jtag Connector Explanation Jumpers Jumper SettingsGlan Ports Enable/Disable Watch Dog Cmos Clear FSB Speed Select VGA Enable/Disable Scsi Termination Enable/ Disable *For X6QT8 only Scsi Controller Enable/ Disable *For X6QT8 only 3rd PWR Fail Detect 3rd PWR Supply PWR Failure Detect JP13 Glan LEDs Onboard IndicatorsOverheat LED JOH1 LeftRight DA1 DA2 LE1 Scsi Channel Indicators DA1, DA2 *X6QT8 onlyOnboard Power LED LE1 Floppy Floppy ConnectorFloppy, IPMI, Hard Disk Drive and Scsi Connections IDE Drive Connectors Pin Deﬁnitions IDE IDE Connectors Installation Ultra320 Scsi ConnectorsX6QT8 Only Ipmi 2.0 SocketPage Before Power On Troubleshooting ProceduresNo Power Losing the System’s Setup Conﬁguration Memory Errors Technical Support Procedures Frequently Asked Questions Returning Merchandise for Service Introduction How To Change the Conﬁguration DataStarting the Setup Utility Processors Main SetupSystem Memory System Time/System Date CPU Conﬁguration Sub-Menu Advanced SettingsConﬁgure Advanced CPU Settings Intel R C-State Technology Max Cpuid Value LimitHyper-Threading Technology IDE Conﬁguration Sub-Menu A.R.T. For Hard disk drives DMA Mode PCI/PnP Conﬁguration Floppy Conﬁguration Super IO Conﬁguration Submenu Advanced Chipset Settings Event Log Conﬁguration Apci Conﬁguration Hardware Health Conﬁguration Temperatures CPU Overheat TemperatureFan Speed Voltage MPS Conﬁguration Active State Power ManagementPCI Express Conﬁguration MPS Revision Remote Access Conﬁguration Smbios Conﬁguration USB Conﬁguration Interrupt 19 Capture Bios Settings Conﬁguration Watch Dog Timer Boot SettingsRestore on AC Power Loss Resume On Modem Ring Hard Disk Drives Boot Device PriorityRemovable Drives CD/DVD Drives Security Settings Exit Options Load Optimal DefaultsSaving Changes and Exit Discarding Changes and Exit Load Fail-Safe Defaults Beep Code Error Message Description Appendix a Bios Error Beep Codes X6QT8/X6QTE+ User’s Manual D0h D1h D3h D4h D5h Uncompressed Initialization Codes Bootblock Recovery Codes Uncompressed Initialization Codes Checkpoint Appendix B Bios Post Checkpoint Codes Checkpoint A9h Aah Abh B0h B1h 00h Page Introduction to the Intel ICH5R I/O Controller Hub ATA Operate ModeCombined Mode Adaptec Embedded Serial ATA with HostRAID Controller Driver Using the Array Conﬁguration Utility ACU Using the Adaptec RAID Conﬁguration Utility ARC Managing Arrays From the ARC menu, select Array Conﬁguration Utility ACU Viewing Array PropertiesEnter Deleting Arrays To create an array Creating Arrays Assigning Array Properties Raid Level Create Via When Appropriate When you are ﬁ nished, press Done as the screen shown below Ctrl+B Adding a Bootable ArrayDeleting a Bootable Array To initialize drives Initializing Disk DrivesPage Page To Rebuild an array Rebuilding Arrays To access the disk utilities Using the Disk UtilitiesPage To Exit Adaptec RAID Conﬁguration Utility You can choose from the following options Installing Intels ICH5R Driver by Adaptec and the Windows OS Installing Other Software Programs and Drivers Supero Doctor Supero Doctor III Interface Display Screen-II Remote Control