Increment Reister, INC register | Texas Instruments MSC1210 manual

						8052 Instruction Set
INC	Increment Reister
Syntax	INC register

	Instructions		OpCode	Bytes	Cycles		Flags

	INC A		0x04	1	1		None

	INC direct		0x05	2	1		None

	INC @R0		0x06	1	1		None

	INC @R1		0x07	1	1		None

	INC R0		0x08	1	1		None

	INC R1		0x09	1	1		None

	INC R2		0x0A	1	1		None

	INC R3		0x0B	1	1		None

	INC R4		0x0C	1	1		None

	INC R5		0x0D	1	1		None

	INC R6		0x0E	1	1		None

	INC R7		0x0F	1	1		None

	INC DPTR		0xA3	1	2		None

INC increments the value of register by 1. If the initial value of register is 255 (0xFFH), incrementing the value causes it to reset to 0.

Note:

The carry flag is not set when the value rolls over from 255 to 0.

In the case of INC DPTR, the two-byte value of DPTR is incremented as an unsigned integer. If the initial value of DPTR is 65 535 (0xFFFFH), increment- ing the value causes it to reset to 0. Again, the carry flag is not set when the value of DPTR rolls over from 65 535 to 0.

See also: ADD, ADDC, DEC

8052 Instruction Set	E-11

Image 295

Texas Instruments MSC1210 manual Increment Reister, INC register

Contents

User’s Guide Important Notice MSC1210 Memory Organization Introduction to the MSC1210Basic Registers System Timing Addressing ModesSerial Communication Analog-to-Digital Converter Pulse Width Modulator/Tone Generator Additional MSC1210 Hardware Serial Peripheral Interface SPI Additional Resource Instruction-Set Quick-Reference Guide Additional Features in the MSC1210 Compared toClock Timing Diagram Boot ROM Routines SPI/PWM/Flash Write Timing System Timing Interrupt Control 16−1 Pin Descriptions of the MSC1210 14−2 Chapter MSC1210 Description −1. MSC1210 Block Diagram MSC1210 Pin-Out −2. Pin Configuration of the MSC1210 Pin # Name Description −1. Pin Descriptions of the MSC1210 Pin # Name Description −1 Pin Descriptions of the MSC1210 AD7 1 I/O Ports P0, P1, P2, and P3 Port Port Oscillator Inputs XTAL1 and XTAL2 Address Latch Enable ALE Reset Line RSTProgram Store Enable Psen External Access EA −3. MSC1210 Timing Compared to Standard 8051 Timing Enhanced 8051 Core Flash Memory Family Device CompatibilityHigh Performance Analog Functions High-Performance Peripherals Description Program Memory Data Memory Internal RAM Program Memory Description MSC1210Y2 MSC1210Y3 MSC1210Y4 MSC1210Y5 −1. Program and Data Memory Size −2. Program and Data Memory Addresses Data MemoryOn-Chip Extended Static RAM Sram External Data Memory On-Chip Flash Data Memory −2. MSC1210 Memory Map Register Bank Internal RAM Register Banks Stack Bit Memory Or execute Special Function Register SFR Memory Defines the MSC1210 SFRs SCON0 −1. SFR Names and Addresses Referencing Bits of SFRs Referencing SFRs SFR Types Bit−Addressable SFRs SFR Definitions SFR Definitions SFR Definitions SFR Definitions Can be generated automatically by the MSC1210 P0DDRL/P0DDRH Port 0 Data Direction Low/High Byte, Addresses GCL/GCM/GCH Gain Low/Middle/High Byte, Addresses D4H/D5H/D6H SFR Definitions SFR Definitions SFR Definitions Describes the basic register functions of the MSC1210 ADC Registers Accumulator Program Counter PC Register Stack Pointer SP Data Pointer DPTR0/DPTR1 Describes the various addressing modes of the MSC1210 Immediate Addressing Mode Example−1. MSC1210 Addressing Modes Direct Addressing Indirect Addressing Movx A,@DPTR Movx @DPTR,A External Direct Addressing Code Indirect Adressing External Indirect Addressing Describes the program flow of the MSC1210 ADC Direct Jumps Conditional Branching Consider the example Returns From Routines Direct CallsInterrupts Description System Timers Startup Timing −1. Standard 8051 Timing System Timing System Timers −2. MSC1210 Timing Chain and Clock Control Milliseconds Timer Microseconds Timer −4. System Timing Interrupt Control One Hundred Millisecond Clock Flash Programming Mode Power-On Reset Timing Normal-Mode Power-On Reset TimingStartup Timing Psen Symbol Parameter Min Max Unit Describes the timers of the MSC1210 ADC Using Timers to Measure Time How Does a Timer Count?How Long Does a Timer Take to Count? Width Width ∝s RD or WR StrobeMovx Duration SYS CLKs At 12MHz −1. Timer Conrol SFRs Timer SFRsSFR Name Description SFR Address Bit Addressable? Mode Tmod SFR TxM1 TxM0 Timer Description of Timer Mode −2. Timer Modes and Usage Instruction −3. Example of 8-Bit Auto-ReloadCycle Tcon SFR Bit Name Bit Address Explanation of Function Timer−4. Tcon 88 H SFR Reading the Timer Initializing a Timer Detecting Timer Overflow Timing the Length of Events Using Timers as Event Counters 1 T2CON SFR Using Timer Timer 2 in Auto-Reload Mode Timer 2 in Capture Mode Timer 2 as a Baud Rate Generator Describes serial communication using the MSC1210 ADC Description Function Length Period Setting the Serial Port Mode Mode −1. SM0 and SM1 Function Definitions High four bits bits 4 through 7 are configuration bits Serial Mode 0 Synchronous Half-Duplex Serial Mode 1 Asynchronous Full-Duplex −2. Serial Port Mode 0 Receive Timing-High Speed Operation −3. Serial Port Mode 1 Transmit Timing BaudRate + 12 @ 256 * TH1 −2. Common Baud Rates Using TimerBaudRate + 32 @ Timer1Overflow BaudRate + Timer2Overflow Baud Rate RCAP2HRCAP2L @ 11.0592MHz f OSC −3. Common Baud Rates Using TimerSerial Mode 2 Asynchronous Full-Duplex Rcap 2H Rcap 2L + BaudRate + 2SMOD @ fOSC −6. Serial Port 0 Mode 2 Receive Timing −7. Serial Port 0 Mode 3 Transmit Timing Serial Mode 3 Asynchronous Full-Duplex Setting the Serial Port Mode Baud Rate Setting the Serial Port Baud Rate−4. Mode 0 Commonly Used Baud Rates TH1 = 256 − Crystal / 192 / Baud Desired Baud −5. Baud Rate Settings for Timer Writing to the Serial Port −6. Baud Rate Settings for TimerBaud Rate 33MHz clk 25MHz clk 11.0592MHz clk Kb/s Reading the Serial Port Describes the interrupts of the MSC1210 ADC JNB TF0,SKIPTOGGLE Events That Can Trigger Interrupts Interrupt/Event Addr Priority Flag Enable Priority Control−1.Interrupt Sources 10-4 −4.EIE E8 H SFR Enabling Interrupts−2.IE A8 H SFR −3.EICON D8 H SFR Polling Sequence −5.IP B8 H SFR Interrupt Priorities−6.EIP F8 H SFR Exiting Interrupts Interrupt Triggering Serial Interrupts Types of InterruptsExternal Interrupts Bit Name Explanation of Function −7.EXIF 91 H SFR Watchdog Interrupt Timer InterruptsAuxiliary Interrupts −9.AIE A6 H SFR −8.Clearing Auxiliary InterruptsAux Interrupt Type Method to Clear Interrupt −11. PAI A5 H SFR −10. Aistat A7 H SFRBit Name Explanation of Function Clear Interrupt PAIx Bits Explanation of Interrupt/Event −12. PPI Bits of PAI SFR −13. EWU C6 H SFR Waking Up from Idle Mode Push PSW Register Protection Push R0 Error − Invalid instruction Common Problems with Interrupts Tone Generator 11-3 Description 11-2PWM Generator 11-5 −1. Block Diagram ToneFrequency +1 Tone Generator Tone Generator Waveforms −3. Timing Diagram of Tone Generator in Staircase Mode Condition Duty Cycle PWM Generator−1. PWM Polarity Conditions Duty Cycle = PWM Period +1 − PWM Duty/PWM Period +1 −5. Timing Diagram of a PWM Waveform This can be expressed in code as −3. Statement Explanations −2. Configuring the PWM for Tone GenerationStmt ‘C’ Source Code Assembly Source Code Example of PWM Tone Generation Example of PWM Tone Generation Idling −5. Statement Explanations −4. Configuring the PWM for Tone Generation with PWM IdlingExplanation −6. PWM Timing Example of Updating PWM 11-12 12-10 PGA DAC −1. MSC1210 Architecture Input Multiplexer −2. Input Multiplexer Configuration Negative Input Positive Input Temperature Sensor 12-6 MSB Burnout Current Sources ACLKFrequency Input BufferAnalog Input @ 10 Programmable Gain Amplifier PGA −1.PGA Settings Modulator Offset DAC Calibration Mode −2.Calibration Mode Control BitsCalibration −4. Filter Step Responses Digital Filter −5. Filter Frequency Responses Samples to Discard Filter Multiplexing Channels−3.Filter Settling −4.Output Data Rate and Channel Rate −5.Output Data Rate and Channel Rate 10x faster Voltage Reference Source Summation/Shifter Register Shift Summation Count Summation Count ADC Summation Mode Manual Summation Mode ADC Summation with Shift Divide Mode Manual Shift Divide Mode Interrupt-Driven ADC Sampling Analog-to-Digital Converter 12-21 Syncronizing Multiple MSC1210 Devices Analog-to-Digital Converter 12-23 ADC Result + R REF @ I OUT Ratiometric MeasurementsADC Result + V REF PT100 Differential Vref 12-26 Description 13-2 Clock Phase and Polarity Controls 13-4SPI Signals 13-5 SPI System Errors 13-6 Functional Description −1. SPI block diagram −2. SPI Clock/Data Timing Clock Phase and Polarity Controls Serial Clock SPI SignalsMaster In Slave Out Master Out Slave SPI System Errors Data Transfers −3. SPI Reset State 13-8 −4. SPI Fifo Operation Fifo Operation Code Examples SPI Master Transfer in Fifo Mode using Interrupts 13-12 Description 14-2 Watchdog Timer 14-4Low-Voltage Detect 14-2 Low-Voltage Detect −1. Brownout Reset and Low-Voltage Detection −3.Band Gap Parameters Power Supply−2.Comparator Specification −1.Typical Sub-Circuit Current Consumption Watchdog Timer Hardware Configuration Watchdog Timer Enabling Watchdog Timer Watchdog Timer Resetting the Watchdog Timer Watchdog Timeout/Activation Disabling Watchdog Timer Breakpoint Generator 15-7 Hardware Configuration 15-2Power Optimization 15-9 Advanced Flash Memory 15-6 Hardware Configuration Registers Hardware Configuration DFSEL2/1/0 Amount of Flash Data Memory Hardware Configuration Register 0 HCR0 Hardware Configuration Register 1 HCR1 Accessing Configuration Memory in a User Program Hardware Configuration Memory Advanced Flash Memory Updating Interrupts with Reset Sector LockWrite Protecting Flash Program Memory Breakpoint Generator Configuring Breakpoints Disabling a Breakpoint Breakpoint Auxiliary Interrupt Power Optimization Flash Memory as Data Memory Advanced Topics 15-11 Advanced Topics and Other Information Describes the 8052 Assembly Language Syntax Label and instruction Expressions Number Bases Order Operator Operator PrecedenceCharacters and Character Strings −1.Order of Precedence for Mathematical Operators Ljmp LABEL3 Changing Program Flow LJMP, SJMP, Ajmp Subroutines LCALL, ACALL, RET MOV DestinationRegister,SourceValue Register Assignment MOV MOV R2,R1 Invalid MOV @R0,A Incrementing and Decrementing Registers INC, DEC Program Loops Djnz Setting, Clearing, and Moving Bits SETB, CLR, CPL, MOV 16-14 Bit-Based Decisions and Branching JB, JBC, JNB, JC, JNC Lcall Debouncekey Value Comparison Cjne Checkless JC Aisless Less Than and Greater Than Comparison Cjne Performing Additions ADD, Addc Zero and Non-Zero Decisions JZ/JNZ Performing Additions ADD, Addc Performing Subtractions Subb Performing Multiplication MUL Performing Division DIV −1. Rotate Operations Shifting Bits RR, RRC, RL, RLC −4.Results of XRL Bit-Wise Logical Instructions ANL, ORL, XRL−2.Results of ANL −3.Results of ORL Assembly Language 16-25 Swapping Accumulator Nibbles Swap Exchanging Register Values XCH Adjusting Accumulator for BCD Addition DA Using the Stack PUSH/POP Assembly Language 16-29 Setting the Data Pointer Dptr MOV Dptr Reading and Writing External RAM/Data Memory Movx Lcall SUB Reading Code Memory/Tables Movc SUB INC a Using Jump Tables JMP @A+DPTR Describes the Keil simulator and its functions 17-2 Keil Simulator 17-3 −1. Timer/Counter 0 − Mode Timers −2. Timer/Counter Timer 0 & 1 Example −4. Timer/Counter 1 Mode Keil Simulator 17-7 17-8 Keil Simulator 17-9 17-10 −1.Timer/Counter 2 Control Bits TimerRegister Bit Toggle Box Name −7. Status of Watchdog Peripheral Watchdog Reset Facility Example 17-14 Keil Simulator 17-15 Clock Control System Timer Analog-to-Digital Converter −8. Analog−to−Digital Converter Peripheral −9. Error Message −10. Accumulator/Shifter Peripheral Summation/Shifter 17.8.1 ADC/Summation/Shifter Example 17-22 Keil Simulator 17-23 17-24 Keil Simulator 17-25 17-26 Keil Simulator 17-27 −11. summation/Shifter Peripheral Keil Simulator 17-29 −13. List Box for the Interrupt Peripheral Ports −14. Parallel Port 0 Contents Display Window −16. SPI Peripheral Window Serial Peripheral Interface SPI Keil Simulator 17-33 SPI Sample Code Keil Simulator 17-35 Serial Peripheral Interface SPI Keil Simulator 17-37 17.12 ∝Vision 2 Debug Program Example −17. Keil Debugger Serial Port I/O −18. Serial Channel 0 Communication Peripheral 17-42 BaudRate + fOSC Transmit Block Baud Rate ComputationBaudRate + fOSC @ Receive Block Baud Rate Computation −19. Clock Control Peripheral Additional Resource Topic Appendix a Additional Features in the MSC1210 Compared to Appendix B Figure B−1. MSC1210 Timing Chain and Clock Control MSC1210 Timing Chain and Clock Control Diagram Appendix C Address Routine Declarations Description Table C−1. Boot ROM Routines Boot ROM Routines Page Appendix D JB bitAddr,relAddr Ajmp pg1Addr 8052 Instruction-Set Quick-Reference Guide Description Instruction Set Appendix E Description Acall codeAddress 8052 Instruction SetAcall Absolute Call within 2k Block Add Value, Add Value with Carry ADD, AddcADD A,operand Absolute Jump within 2k Block AjmpAjmp codeAddress Bitwise ANLANL operand1,operand2 Cjne operand1,operand2,reladdr Compare and Jump if Not EqualCLR Clear Register CPL operand Decimal Adjust AccumulatorCPL Complement Register See also INC, Subb Decrementing the value causes it to reset to 255 0xFFHCarry flag is not set when the value rolls over from 0 to DEC register Djnz register,relAddr Decrement and Jump if Not Zero Increment Reister INCINC register Jump if Carry Set Jump if Bit SetJBC Jump if Bit Set and Clear Bit JNB JMPJNC Lcall JNZLjmp Not affected See also MOVC, MOVX, XCH, XCHD, PUSH, POP MOV operand1, operand2MOV bit1,bit2 Move into/out of Internal RAM MOVMOV operand1,operand2 Movc MOV DptrMovx No Operation MULMultiply Accumulator by B NOP Bitwise or ORLSyntax ORL operand1,operand2 Push Value onto Stack POPPop Value from Stack Push Return from Interrupt RETReturn from Subroutine Reti RRC RLCSetb Subtract from Accumulator with Borrow SjmpShort Jump Subb XCH SwapXchd Bitwise Exclusive or XRL Instructions OpCode Bytes Cycles Flags ??? 0xA5 Undefined Appendix F Bit Addressable SFRs alphabetical Enable Interrupt Control EiconExtended Interrupt Enable EIE EX2-External 2 Interrupt Enable Extended Interrupt Priority EIP Interrupt Enable IE Port 0 P0 Interrupt Priority IP Port 2 P2 Port 1 P1 Port 3 P3 Register Bank Register Bank Addresses Program Status Word PSW Serial Control Scon Serial Mode Description Baud Tcon Timer Control Tcon T2CON Timer 2 Control T2CON Appendix G SFR Name Description SFR Address Hex SFR/Address Cross-Reference SFRs/Address Cross-Reference Guide alphabetical Spircon