Toshiba RAV-SM2802DT-E Remote controller switch monitoring function, Filter sign setting

Concealed Duct High Static Pressure

Procedure 6

When settings have been completed, push button to determine the settings.

When button is pushed, “SETTING” flashes and then the display content disappears and the air conditioner enters the normal stop mode. (While “SETTING” is flashing, no operation of the remote controller is accepted.)

Installation Manual

nPower saving mode

1.Push button for at least four seconds when the air conditioner is not working.

flashes.

Indicates CODE No. “C2.”

2. Select an indoor unit to be set by pushing (left side of the button).

Each time you push the button, unit numbers change as follows:

Concealed Duct High Static Pressure Installation Manual

nRemote controller switch monitoring function

This function is available to call the service monitor mode from the remote controller during a test run to acquire temperatures of sensors of the remote controller, indoor unit, and outdoor unit.

nFilter sign setting

According to the installation condition, the filter sign term (Notification of filter cleaning) can be changed.

Follow to the basic operation procedure

( 1 → 2 → 3 → 4 → 5 → 6 ).

•For the CODE No. in Procedure 3, specify [01].

•For the [SET DATA] in Procedure 4, select the SET DATA of filter sign term from the following table.

	SET DATA	Filter sign term
	0000	None
–	0001	150H
96	0002	2500H (Factory default)
	0003	5000H
–
	0004	10000H

UNIT No.	UNIT No.	UNIT No.
1-1	1-2	1-3

UNIT No.

1-4

The fan of the selected unit runs.

3.Adjust the power save setting by pushing

TIME / buttons.

Each push of the button changes the power level by 1% within the range from 100% to 50%.

∗ The factory default is 75%.

2

4

1 3

1.Push and buttons simultaneously for at least 4 seconds to call the service monitor mode. The service monitor indicator lights up and the header indoor unit number is displayed first. CODE No. ￿￿ is also displayed.

2.Pushing TEMP. / buttons, select the number of sensor, etc. (CODE No.) to be monitored. (See the following table.)

3.Pushing (left side of the button), select an indoor unit to be monitored.

The sensor temperatures of indoor units and their outdoor unit in the control group are displayed.

4.Push button to return to the normal display.

n To secure better effect of heating

When it is difficult to obtain satisfactory heating due to installation place of the indoor unit or structure of the room, the detection temperature of heating can be raised.

Also use a circulator, etc. to circulate heat air near the ceiling.

Follow to the basic operation procedure

( 1 → 2 → 3 → 4 → 5 → 6 ).

•For the CODE No. in Procedure 3, specify [06].

•For the set data in Procedure 4, select the SET DATA of shift value of detection temperature to be set up from the table below.

SET DATA	Detection temperature shift value
0000	No shift
0001	+1°C
0002	+2°C (Factory default)
0003	+3°C
0004	+4°C
0005	+5°C
0006	+6°C

Setting of power level in power saving mode

4.Determine the setting by pushing button.

5.Push button to complete the setting.

	Indoor unit data
CODE No.	Data name
01	Room temperature (remote controller)
02	Indoor unit intake air temperature (TA)
03	Indoor unit heat exchanger (coil)
	temperature (TCJ)
04	Indoor unit heat exchanger (coil)
	temperature (TC)
F3	Indoor unit fan cumulative operating hours
	(× 1 h)

	Outdoor unit data
CODE No.	Data name
60	Outdoor unit heat exchanger (coil)
	temperature (TE)
61	Outside air temperature (TO)
62	Compressor discharge temperature (TD)
63	Compressor suction temperature (TS)
64	—
65	Heatsink temperature (THS)
6A	Operating current (× 1/10)
F1	Compressor cumulative operating hours
	(× 100)

– 29 – – 30 –