Setting the Site Startup Key, Set Frequencies New | Uniden UBCD996T

Notes:

Access single-digit system/site Quick Keys by pressing the single digit on the keypad during scanning. Access two-digit system Quick Keys by pressing [.No] then both digits.

You can assign as many systems to the same quick key as you want.

To be scanned, a system’s Quick Key must be activated and the system must be unlocked.

Setting the Site Startup Key

MESL

[MENU] Program System

Select a trunked system

Edit Site

Select a Site

Set Startup Key

Select a startup key from 0-9 or select “.” for no startup key.

Notes:

To unlock the system at startup, press and hold the selected startup key while you turn on the scanner.

The system Quick Key is also enabled.

If you press a different key at startup, the system is locked out.

If you do not assign the system a startup key, the system is not affected by any key press during startup.

Setting Site Frequencies

MESL

[MENU] Program System

Select a trunked system

Edit Site

Select the site

Set	Frequencies
New	Frequency (or select an existing frequency)	Input a site frequency
using the number keys and [.No] key, then press		. If you are entering

frequencies for an LTR or EDACS system, the scanner will also prompt you to enter the LCN for the frequency you just entered. LCN’s (logical channel numbers) are provided from the same source where you got the other system information.

To enter additional frequencies, press [MENU], then to select New Frequency. Then repeat the above.

78

Image 78

Uniden UBCD996T manual Setting the Site Startup Key, Setting Site Frequencies, Set Frequencies New

Contents

UBCD996T Precautions Earphone Warning Power Related Issues Table of Contents Optimizing P25 Performance Programming Your Scanner Using the Close Call Feature 100 Care and Maintenance 125 This page is intentionally blank This page is intentionally blank Introduction Feature Highlights GeneralPage GPS Priority SearchAuto Store PC Control and Cloning Memory Storage Limits Using the Scroll Control Search Lockout Limits About This Manual How the Scanner’s Controls Are Represented in This Manual Entering Text Within a Menu OptionMenu Program System Select the system Page Page Understanding Scanning and the UBCD996T Understanding the Scanner’s MemoryUnderstanding Quick Keys What is Scanning? What is Searching?What is CTCSS/DCS? Conventional Scanning Simplex Operation What is Trunk Tracking? Repeater Operation Trunked Scanning Types of Trunking SystemsMotorola Trunking Edacs Trunking LTR Trunking Startup Configuration Setup/OperationMulti-Site Trunking Where To Get More Information Call Motorola/EDACSInformation On The Internet Included With Your Scanner Setting Up Your Scanner Base Station UBCD996T Setting Up an Audio Recording Device or Computer Recording Vehicle InstallationMounting Using the Bracket Mounting Using the DIN-E Sleeve Page Mounting Using ISO Technique Removing the Scanner from the DIN-E Sleeve Connecting an Optional Antenna Connecting an Earphone/HeadphoneRemoving the Display Sticker Connecting an Extension Speaker Controls, Keys, and Functions + Press Srvc Page Srvc Look At The Display Turning On the Scanner and Setting the Squelch OperationStartup Key Operation Scanning Systems Menu Search for… Edit Custom Selecting Systems to Scan Selecting System Channel Groups ID Scan/ID Search Mode Locking/Unlocking SystemsLocking/Unlocking Channels Quickly Storing an ID During ID Search Holding On a SystemHolding On a Channel Quick-Storing Channels or Talk Group ID’s Tgid Trunking Activity Indicators Toggling the Display Mode Conventional System Edit Sys Option Adjust P25 LevelOptimizing P25 Performance Trunked SystemPage Using the Menu Setting the Dimmer Programming General SettingsSetting and Using the Backlight Menu Settings Set Backlight Set Dimmer Adjusting the Key Beep Setting the Audio AGCSetting the Backlight Color Setting the GPS Format Setting the Display OrientationAdjusting the Display Contrast Setting the Position Format Setting the Time Zone Setting the Serial Port SpeedSetting the Time Format Setting the Distance Units Viewing Memory Used Displaying Scanner InformationInitializing the Scanner’s Memory Viewing the Firmware Version and Electronic Serial Number Volume/Squelch with PC Control Connecting Your Scanner to a Personal ComputerWired Cloning Restore Preprogram List? Yes=E/No=Page Programming Your Scanner General NotesPage Page Page Programming Conventional Systems Programming Trunked Radio Systems Editing the System NameMenu Program System New System Editing the System Quick Key Specifying the Correct System TypeProgramming System Options Edit Name Setting the Startup Key Setting the System Lockout Setting Channel Delay Time Setting the System Hold TimeSetting ID Scan/ID Search Setting Data Skip Program System Setting Location InformationSetting the Fleet Map Edit Sys Option Edit Fleet Map Setting the Status Bit Setting End Code OperationSetting I-Call Operation Edit Sys Option Emergency Alert Setting the Emergency Alert OptionSetting the Edacs ID Format Set Level Setting the System Record Option Reviewing ID Search LockoutsClearing All Locked Out ID’s Adjust the P25 Decode Threshold Editing SitesEditing Channel Groups Copying Systems Setting the Site NameProgramming Sites Deleting Systems Setting the Site Quick Key Menu Program System Select a trunked system Edit Site Setting the Site Startup Key Setting Site FrequenciesSet Frequencies New Setting Site Lockout Setting Site ModulationSetting Site Attenuation Set Modulation Setting Site Hold Time Editing the Band Plan VHF and UHF only Edit Band Plan Setting P25 Band PlansSetting Control-Channel Only Mode Except for P25 Edit Site current Setting Site Location Information Adjust P25 Level Editing a Channel Group Name Setting Up a Channel GroupProgramming Channel Groups Deleting Sites Setting the Group Quick Key Editing ChannelsLocking Out Channel Groups Editing the Channel Name Alpha Tag Deleting Channel GroupsCreating a Channel Delete Group Confirm Delete? Yes=E / No= Editing Frequencies Editing the Talk Group IDEdit Frequency Edit Tgid Setting the Audio TypeSelecting CTCSS/DCS Tones Set Audio Type Select from All, Digital Only, Analog Only Setting Channel Modulation Method Quick CTCSS/DCS SaveSet Audio Type Analog Only Setting Channel Attenuation Setting Channel PrioritySet Priority Setting Channel Alert Set Alert Deleting a Channel Setting LockoutCopying a Channel Edit Group Edit Channel Searching and Storing Service SearchMenu Search for Service Search Quick Search? Yes=E / No= Menu Search for Custom Search Quick SearchCustom Search Quick Search? Yes=E / No= Press .No then to Custom Search Editing a Custom Search Range Menu Search for Edit Custom Custom 1, Custom 2 to CustomQuick Search? Yes=E / No= Press .No then to Edit Custom Search With Scan Method One Set Delay TimeEditing a Service Search Method Two Assigning a Search Range to a Search Key Set AttenuatorSet Record Saving a Found Channel Quick Save Conventional Search and Store Auto Search and StoreSelecting a System Menu Search for Search and Store Trunked Search and Store Using the Close Call Feature Setting Close Call OptionsMenu Close Call 10/15/30/45/60 sec Close Call Hits Close Call Hits with Scan 103 Search and Close Call Options Managing Locked-Out Frequencies Searching for Subaudible Tones Unlocking All FrequenciesReviewing Locked-Out Frequencies Screening Out Broadcast Sources Finding Repeater Output Frequencies Srch/CloCall Opt Repeater Find On or Off Setting the Maximum Auto Store ValueSetting the Modulation Type Menu Srch/CloCall Opt Max Auto Store Menu Srch/CloCall Opt Set Attenuator Setting AttenuationSetting Data Skip Menu Srch/CloCall Opt Set Data Skip Setting Record Setting the Delay TimeSetting the Search Frequency Step Adjust P25 Level Menu Srch/CloCall Opt Adjust P25 Level Priority ScanMenu Set Priority Choose Off, On, or Plus On This page is intentionally blank 112 113 Menu Tone-Out for Tone-Out Setup Setting Tone-Out StandbySetting Up Tone-Out Fire Tone-Out 115 Tone-Out Multi-Channel Monitoring GPS Compatibility Connecting Your Scanner to a GPS DeviceLocation-Based GPS Scanning Initial GPS Operation 118 Non-Radio Location Based GPS Features Setting the Options Menu Program LocationNew Location Deleting a Location Delete Location GPS Display Mode GPS Review Location Mode 124 General Use Care and MaintenanceCleaning Location Troubleshooting 127 128 Specifications Frequency Range MHz NFM 131 Preset Fleet Maps Reference 133 User Defined Fleet Maps Type I Programming Information Size Code Restrictions 136 137 138 139 Index LTR CTCSS/DCS 143 Parts Covered 145 Memo 147