Canadian industry requirements | Xerox DOCUTECH 65 specs

Introduction

Operator Guide

Canadian industry requirements

Notice: The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.

•Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

•Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

•Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

CAUTION

Users should not attempt to make such connections themselves, but should contact the electric inspection authority, or electrician, as appropriate.

•The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop that is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100.

For service in Canada call (800) 939-3769

iv	DocuTech 65/DocuPrint 65

Image 8

Xerox DOCUTECH 65 manual Canadian industry requirements, For service in Canada call 800

Contents

Xerox Document Services Platform USA Table of contents Paper and other stock MaintenanceProblem solving Powering down the system About this guide Contents Telephone requirements Service requirementsRequirements For service in Canada call 800 Canadian industry requirements European Union Electromagnetic comparabilityUnited States Introduction Operator Guide DocuTech 65/DocuPrint Symbology Hot surface symbol European Union declaration of conformity Approvals and certification Operator Guide Safety notes Electricity at Work Regulation UK Regulation Question What is the Electricity at Work Regulation? Check your understandingQuestion Is Xerox equipment safe? Question Is the Xerox equipment in my premises safe? Question I require records of all tests Your responsibilityAdditional queries Electrical safety Printer Controller Printer power on/off indicator Power on/off indicator Printer or controller emergency power off Printer ozone information Printer laser safety Printer operational safety Safety Quality Standards Other National Standards Do these Additional information USA Additional information Europe Safety notes Operator Guide DocuTech 65/DocuPrint Product overview Hardware components Controller components Controller components Printer components Green or Gold colored areas act as markers Paper trays trays Trays Bypass tray tray Bypass Tray High Capacity feeder tray High Capacity Feeder Loading paper in Trays Tray guides and loading paperPerformance capabilities Loading paper in the Bypass Tray Tray Loading paper in the High Capacity Feeder TrayBypass Tray here High Capacity Feed Tray here Changing the Tray 6 settings Changing the guides from 8.5 x 11 inches to A4Page Finisher Top TrayStacker Tray Press the Finisher Button to Finishers before the end Stapling Finishers after the end Unloading the Stacker during printing Staple placementStaple placement 10. Special accessory shelf Peripheral hardware components Controller software Modems Product overview Operator Guide DocuTech 65/DocuPrint Maintenance Power-on procedures Controller power-on procedure Controller power-on button and LED Printer power-on procedure Printer power-on Power-off procedures Printer power-off Preferred Method Alternate MethodPrinter power-off from the controller Printer Power-Off Using The Printer Switch Printer power-off Printer Power-Off Using The Red Button Printer power-off, red button Controller power-off Controller power-off button and LED Emergency power-off procedures Paper jams Printer faultsClearing printer faults Jam clearance areas Finisher area Access to area Replaceable units and supplies Location of CRUs and supplies Replaceable items Ordering CRUs and other suppliesTelephone numbers for orders Supplies Life expectancy for CRUs and consumable supplies Fuser CRUXerographic CRU Paper Feed Roll 21,700 43,400 130,200 Dry ink toner usage and area coverage6R849 6R821 Paper and other stock Performance information Paper handling guidelines Tray capabilities Staple capability for various paper weights General stapling guidelines Performance tables Symbols Characters Printer performance for standard paper 20 lb USA LetterLegal Ledger Printer performance for standard paper 80 gsm Xerox Europe A4 CoverFoolscap Spanish Sp. Folio Printer performance for non-standard paper and other stocks TransparenciesLabels GBC brand pre-punched Sameceda Recommendations for loading special stock Reinforced Mylar EdgeCard stock Tabs GBC stock Sameceda Storing Recommendations for handling, loading, and storing paperLoading and handling Problem solving Avoiding the problems Solving the problems Handling There are jams Check the paper path for Calling the Welcome Center Problem solving Operator Guide DocuTech 65/DocuPrint