6. Recommendations for loading special stock | Xerox DOCUTECH 65

Reinforced Mylar

Paper and other stock				Operator Guide
	Table 3-6. Recommendations for loading special stock

	Stock Type	Common Use		Recommendation

	Reinforced Mylar	Ringed binders	•	Load reinforced edge on the
	edge			right in Trays 1-4.
	3 or 4 holes		•	Load reinforced edge on the
				left in Trays 5-6.
			• Use long-edge feed only.

	Card stock	Covers, signs	•	Feed from the Bypass Tray for
				best results.

	Tabs	Separators within	•	Use the Tab Tray insert.
		a document	• Feed from trays 2, 3, and 4
			• Feed from trays 2, 3, and 4
				only.
			• Load with the tabs on the right.

	Transparencies	Presentations	•	Use clear or white-striped
				transparencies. Do not use
				paper-backed transparencies.
			• Feed from the Bypass Tray
				(Tray 5) preferred.
			• Refer to the label on the tray
				for the orientation of striped
				transparencies.
			•	When using transparencies
				with removable stripes, load
				with the stripe up in Tray 5 and
				the stripe down in Tray 1.
			•	Do not duplex.

	Labels	Self-adhesive	•	Do not duplex.
		labels for	• Feed labels into the printer
		envelopes and	• Feed labels into the printer
		envelopes and		LEF only.
		packaging		LEF only.
		packaging
				Labels pose a special problem
				because, depending on the
				number of labels per sheet,
				there is an opportunity for the
				label to separate from the
				backing while inside the
				printer.
			• Load face-up in Trays 1-4.
			• Load face-down in Trays 5-6.

3-10	DocuTech 65/DocuPrint 65

Image 66

Xerox DOCUTECH 65 6. Recommendations for loading special stock, Reinforced Mylar, edge, 3 or 4 holes, Card stock, Tabs

Contents

Xerox Document Services Platform DocuTech 65/DocuPrint Operator Guide Xerox Corporation Global Knowledge and Document Services 800 Phillips Road Building 845-17S Webster, New York USA2001 by Xerox Corporation. All rights reserved Introduction Table of contentsSafety notes 1. Product overview 2. Maintenance 4. Problem solving3. Paper and other stock Powering down the system IntroductionAbout this guide Contents Telephone requirements Service requirementsRequirements Xerox Customer Support 1301 Ridgeview Drive, Bldg Lewisville, TX Canadian industry requirements For service in Canada call Electromagnetic comparability United StatesEuropean Union Introduction Figure 1. Hot surface symbol Safety notesSymbology Figure 2. Heated surface symbol European Union declaration of conformity Approvals and certification This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Electricity at Work Regulation - UK The Regulation Question Is Xerox equipment safe? Check your understandingQuestion What is the Electricity at Work Regulation? Question Is the Xerox equipment in my premises safe? THE USE OF INAPPROPRIATE TEST PROCEDURES AND TEST Your responsibilityAdditional queries PERSONS WHO POSSESS THE RELEVANT SKILL, KNOWLEDGE AND Electrical safety Printer Controller Printer power on/off indicator Figure 3. Power on/off indicator Printer or controller - emergency power off Printer - ozone information Printer - laser safety Printer - operational safety Safety Quality Standards Other National Standards Do these Additional information - USA Additional information - Europe Safety notes 1. Product overview Hardware components Controller components Figure 1-1. Controller components Tray 5, Bypass Printer componentsFigure 1-2. Printer components Stacker Finisher for stapled sets NOTE To achieve the maximum copying speed, paper should be loaded Paper trays traysFigure 1-3. Trays Long Edge Feed in the paper trays whenever possible Bypass tray tray Figure 1-4. Bypass Tray High Capacity feeder tray Figure 1-5. High Capacity Feeder Loading paper in Trays Tray guides and loading paperPerformance capabilities Figure 1-6. Loading Trays Figure 1-7. Loading Trays 5 and Loading paper in the Bypass Tray TrayLoading paper in the High Capacity Feeder Tray Bypass Tray here Changing the Tray 6 settings Figure 1-8. Changing the guides from 8.5 x 11 inches to A4 Product overview Stacker Tray FinisherTop Tray Figure 1-9. Finisher components Finishers before the end of StaplingFinishers after the end of Staple placement Unloading the Stacker during printingTable 1-1. Staple placement Peripheral hardware components Figure 1-10. Special accessory shelf Controller software Modems 1-16 2. Maintenance Power-on procedures Controller power-on procedure Figure 2-1. Controller power-on button and LED Printer power-on procedure Figure 2-2. Printer power-on Preferred Method Alternate Method Power-off proceduresPrinter power-off Printer power-off from the controller Figure 2-3. Printer power-off Printer Power-Off Using The Red Button Figure 2-4. Printer power-off, red button After the Red Button is used, the printer will take longer to rebootRED BUTTON Controller power-off Figure 2-5. Controller power-off button and LED Emergency power-off procedures Controller Power- Off Printer power-offController or Printer Emergency Conditions Paper jams Printer faultsClearing printer faults Xerox Document Services Platform Series Problem Solving Guide and the Figure 2-6. Jam clearance areas Figure 2-7. Finisher area 2-11 Figure 2-8. Access to area 2-12 Replaceable units and supplies Figure 2-9. Location of CRUs and supplies Table 2-1. Telephone numbers for orders Replaceable itemsOrdering CRUs and other supplies Supplies Xerographic CRU Table 2-2. Life expectancy for CRUs and consumable suppliesFuser CRU Paper Feed Roll Table 2-3. Dry ink toner usage and area coverage Dry Ink Toner usage and “Dry Ink Low” message“Dry ink is low” message PRINTS PER 3. Paper and other stock Performance information Paper handling guidelines Feed Direction The dimension of this edge is controlled by the trayFigure 3-1. Size requirement for duplex printing Figure 3-2. Tray capabilities Figure 3-3. Size requirements for stapling General stapling guidelinesTable 3-1. Staple capability for various paper weights This edge Symbols Characters Performance tables Legal Table 3-2. Printer performance for standard paper 20 lb USALetter Ledger Foolscap Table 3-3. Printer performance for standard paper 80 gsm Xerox EuropeA4 Cover Spanish Sp. Folio Pre-drilled/pre-punched holes standard LetterheadPre-printed forms locations Table 3-5. Printer performance for new and recycled plain paper Recommendations for loading special stockPaper Weight Throughput Material 8.5 x 11 in. or A4 Reinforced Mylar edgeCard stock GBC stock Sameceda Recommendations for handling, loading, and storing paper Loading and handlingStoring 4. Problem solving Avoiding the problems Power Solving the problemsTable 4-1. Troubleshooting tips Controller Stock handling handling Calling the Welcome Center Problem solving Operator GuideDocuTech 65/DocuPrint