After auto setup, 1OUT of Phase, 3LEVEL Error | Yamaha RX-V1500

AUTO SETUP

After auto setup

Press l / h to display the detailed information about individual warnings.

Warning message	Cause	Remedy

W-1:OUT OF PHASE	Speaker polarity is not correct. This message	• Check the speaker connections for proper polarity
	may appear depending on the speakers even	(+ or –).
	when the speakers are connected correctly.

W-2:OVER 24m	The distance between the speaker and the	• Bring the speaker closer to the listening position.
(80ft)	listening position is over 24 m (80 ft).
(80ft)

W-3:LEVEL ERROR	The difference of volume level among speakers	• Readjust the speaker installation so that all speakers
	is excessive. (No level correction is made.)	are set in locations with similar conditions.
		• Check the speaker connections.
		• Use speakers of similar quality.
		• Adjust the output volume of the subwoofer.

W-4:SWFR PHASE	The phase polarity of the subwoofer is not	• Select the opposite phase on the subwoofer if the
	correct.	subwoofer has a phase switch.

W-5:VOL ERROR	The result may not be correct because the	• Perform the auto setup procedure again. Do not
	volume was changed during the auto setup	change the volume during the auto setup procedure.
	procedure.

•If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again.

•If warning W-1, W-4 or W-5 appears, corrections are made, but they may not be optimal.

•If warning W-2 or W-3 appears, no corrections are made.

•If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center.

30

Image 32

Yamaha RX-V1500 owner manual After auto setup, 1OUT of Phase, 3LEVEL Error, 4SWFR Phase, 5VOL Error

Contents

RX-V1500 For U.K. customers Special Instructions for U.K. Model Contents Features Built-in 7-channel power amplifierSound field features Other features Getting Started Supplied accessoriesInstalling batteries in the remote control Controls and Functions Front panel Europe models only Opening and closing the front panel Door Remote control AMP/SOURCE/TV MuteSET Menu Night Approximately 6 m 20 ft Using the remote controlHandling the remote control Front panel display 96/24 indicator LFE indicatorInput channel indicators Presence and surround back speaker indicators Voltage Selector Rear panelAC Outlets Speaker Setup Speaker placement 10 mm 3/8 Speaker connectionsDi-pole speaker layout Connecting to PRESENCE/ZONE 2 or Presence speaker terminals Tighten the knob to secure the wireBanana plug connections Speaker terminal wrench Red positive + Black negative SUB Woofer Front terminals Center terminalsSurround terminals Subwoofer jack Connections Cable indicationsAnalog jacks Digital jacks Connecting video components Connections for DVD playbackDVD player A. model Video Monitor Multi-format player External decoder Connecting to the Multi CH Input jacksFor 6-channel input Connections for other video components Video AUX jacks on the front panelUse these jacks to connect any video source, such as Game console or camcorder, to this unit Connections for audio components Connecting audio componentsConnecting a turntable Connecting to an external amplifier Connecting the antennas Connecting the AM loop antennaFrequency Step switch Asia and General models only 75-ohm/300-ohm antenna adapter U.K. model only Connecting the power supply cord Other modelsAsia and General models only Memory back-up Speaker impedance setting Turning on the powerPress STANDBY/ON to exit the setting SP IMP . SET Introduction Auto SetupOptimizer microphone setup SET Menu Starting the setupAutomenu If you selected Auto in step If you selected Step in stepIf you selected Reload in step Press n to select Start Push i, then press h During auto setup Troubleshooting for auto setup procedureBefore auto setup After auto setup 1OUT of Phase3LEVEL Error 4SWFR Phase Basic Setup Using Basic MenuBasic Menu 1/2 Press n to select SWFR, then press l / h to select Basic Menu 2/2 Bspeaker LevelPress n to select Check OK?, then press l / h to select Memory back-up Adjust the volume to the desired output level PlaybackBasic operations Select the input source Program name Front panel operationRotate Program to select the desired program Remote control operation To adjust the toneTo listen with headphones Additional operations Selecting the Multi CH Input Enjoying multi-channel software 7.1 channel surroundAuto Auto Decoders select with l / h Press Standard on the remote control to select the decoder To cancel, press Pure Direct againEnjoying 2-channel software in surround Listening to high fidelity stereo sound With Pure Direct This adjusts the level of compression Listening to high fidelity stereo sound With Direct StereoNight listening modes Front panel display automatically dims Listening to unprocessed input signals Downmixing to 2 channelsVirtual Cinema DSP Playing video sources Background Selecting input modes Displaying information about the input SourceDTS Analog Tuning Automatic and manual tuningAutomatic tuning Manual tuning Presetting stations Automatically presetting FM stationsAutomatic preset tuning options Press FM/AM to select the FM band Manually presetting stations Tune into a stationPress Memory MAN’L/AUTO FM Repeat steps 1 through 5 to store other stations Selecting preset stations Exchanging preset stationsPress and hold PRESET/TUNING Edit for more than 3 seconds Press PRESET/TUNING Edit again Receiving RDS stations Changing the RDS mode Press PTY Seek Mode to set this unit in the PTY Seek mode To exit from the PTY Seek mode, press PTY Seek Mode againPTY Seek function Selected program type appears on the front panel display To cancel this function EON function Special considerations when recording DTS software Recording Sound Field Program Descriptions For movie/video sources Dolby Digital SUR. Standard Dolby DigitalSUR. Enhanced SUR. Standard PRO Logic SUR. Standard PRO Logic For music sources Concert HallJazz Club Rock Concert Advanced Operations Selecting the OSD mode Using the sleep timerSetting the sleep timer Control range is from +10 dB to -10 dB Canceling the sleep timerPress l / h to adjust the speaker output level Using the test tone Set AMP/SOURCE/TV to AMP Press Test SET Menu Basic MenuSound Menu Input Menu Using SET Menu Option Menu Using Sound Menu Sound Menu 1/3Center SP Front SP Surr B L/R SP LFE/BASS OUTSurround left/right speakers Surr L/R SP Presence speakers Surround back speakers Surr B L/R SP Speaker distance CSP Distance Cross OverCSP Distance Graphic EQ Dgraphic EQElfe Level Fdynamic Range Glow FRQ.TEST HHP Tone CtrlIaudio SET Low frequency test Glow FRQ. Test Using Input Menu Input MenuCMPNT-V Input Optical OUT Binput Mode OpticalCinput Rename Coaxial Using Option Menu Dmulti CH InputOption MENU1/2 Adisplay SET Speaker impedance setting Bmemory GuardCPARAM. INI DSP IMP.SET Ezone SET FZONE2 SETGZONE3 SET Zone 2 set FZONE2 SET Remote Control Features Control areaControlling this unit Controlling other components Setting remote control codes Remote Control Code Default SettingsControlling optional components Optn area Set AMP/SOURCE/TV to Source Press Learn again to exit from the setup mode Press EnterPress Enter to set the number Function Press an input selector button to select a source component To 10 cm 2 to 4 Learn appears in the display window Press Learn using a ballpoint pen or similar objectPress Learn again to exit the learning mode Changing source names Display window Macro buttons First Second Third Using the Macro featurePress a macro button Press Macro using a ballpoint pen or similar object Macro operationsProgramming macro operations Set Macro ON/OFF to on Press a macro button Press Clear by using a ballpoint pen or similar object Press k / n to select the clear modeClearing function sets Clear appears in the display window Clearing a learned function Press Clear to exit from the clearing modeClearing individual functions Press Clear to exit the clearing mode Clearing a macro functionPress Learn again to exit Press Macro again to exit Controlling each component VCR System configuration and connection example Using external amplifiersZone 2/ZONE Zone 2/Zone 3 connections To enable Zone mode on the remote Control Using this unit’s internal amplifierPress Learn to complete the Zone setup To control Zone 2/Zone Press Select k/n to exit from the Zone Zone 3 mode Turning this unit to either on or standbySpecial considerations for DTS software For DVDs encoded with DTS What is a sound field? Changing parameter settingsEditing Sound Field Parameters Elements of a sound field Resetting parameters to the factory values To reset a certain parameterTo reset all parameters Press k / n to select Parameters Room SIZE/P. Room Size Room size INIT. DLY/P. INIT. DLY Initial delaySound Field Parameter Descriptions INIT. DLY Surround initial delay SB INI. DLY Surround back initial delayRoom Size Surround room size Liveness Surround liveness REV. Level Reverberation level REV.DELAY Reverberation delayREV.TIME Reverberation time DIALG.LIFT Dialog lift For 7ch StereoFor DTS Neo6 Music Image Center image For THX Cinema DEC 2ch Decoder Select Troubleshooting General Sound suddenly Goes offOnly the speaker on One side can be Or DTS indicator Volume level isRecord Volume level Dolby Digital or DTS Tuner Remote control Does not work norFunction properly Does not learn new Glossary Audio formats Sound field programs PCM Linear PCM Audio information LFE 0.1 channelSampling frequency and number Quantized bits THX Cinema processing Video signal information Specifications